Dell PowerEdge M420 User Manual
16 port 10gbe pass through module (xaui)
Hide thumbs
Also See for PowerEdge M420:
- Reference manual (1682 pages) ,
- Configuration manual (1246 pages) ,
- Getting started manual (202 pages)
Table of Contents
Quick Links
See also:
Administrator's Manual, User Manual
Table of Contents
Related Manuals for Dell PowerEdge M420
Summary of Contents for Dell PowerEdge M420
- Page 1 Dell and the Dell logo are trademarks of Dell Inc. Dell 10GbE Pass Through Module (XAUI) User Manual P/N: M1601P Rev 1.0...
- Page 2 © 2010 Dell Inc. All rights reserved. Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden. Trademarks used in this text: Dell™, the DELL logo, and PowerEdge™ are trademarks of Dell Inc.;...
-
Page 3: Table Of Contents
Dell -10GbE PTM Rev 1.0 Table of Contents Intended Audience Conventions Chapter 1 Overview Features Serial Number and Product Version Information Chapter 2 Installation and Basic Operation Unpacking the Pass Through Module Insertion and Removal of the PTM 2.2.1 PTM Insertion 2.2.2 PTM Removal... -
Page 4: Related Documentation
Rev 1.0 Related Documentation The documentation set accompanying the Pass Through Module includes the following: Table 1 - Reference Documents and Web Sites Firmware and Firmware Update Tools Dell Pass Through Module Software User Manual Latest Supported Cables and Optical Modules... -
Page 5: Intended Audience
Rev 1.0 About this Manual This User Manual is for the Dell 10Gb Ethernet Pass Through II passs through module. This manual describes the installation and basic use of Dell 10GbE 16 port Pass Through Module for blade servers. Intended Audience This manual is intended for users and system administrators responsible for installing and setting up the Dell 10GbE 16 port Pass Through Module for blade servers. -
Page 6: Chapter 1 Overview
Rev 1.0 Overview Overview The PTM is an I/O module designed for the PowerEdge M1000e Dell Chassis. The product pro- vides 10Gigabit connectivity for blade servers to Ethernet LANs. The product supports the follow- ing Ethernet protocols. Table 2 - Protocols... -
Page 7: Serial Number And Product Version Information
Dell -10GbE PTM Rev 1.0 • System status LEDs: Power Supply, Status Serial Number and Product Version Information The serial number and product version information are found on the label seen in the figure below. Figure 2: Generic Product label... -
Page 8: Chapter 2 Installation And Basic Operation
If anything in the package is damaged or missing, please contact your customer representative immediately. Insertion and Removal of the PTM The Dell 10Gb Ethernet Pass Through II may be plugged into fabric slots B1, B2, C1, and C2. Determine which slot to use, based on desired system configuration. 2.2.1 PTM Insertion... -
Page 9: Ptm Removal
Dell -10GbE PTM Rev 1.0 The PTM supports hot-insertion into the chassis. If the PTM is inserted to a powered chassis, the power LED (green) should turn on immediately. 2.2.2 PTM Removal The PTM supports hot-removal. It may be removed when the chassis is powered on or off. -
Page 10: Led Indicators
Rev 1.0 Installation and Basic Operation LED Indicators 2.4.1 System LEDs The system status LEDs indicate whether the PTM is receiving power from the chassis, and the state of the PTM. There are two system LEDs on the end of the module. The LED indications and meanings are explained in the figure and table below. - Page 11 Dell -10GbE PTM Rev 1.0 ignated by a constant yellow LED indication. A valid data activity link with data transfer is desig- nated by a blinking yellow LED indication. If the LEDs are not active, either the physical link or the logical link (or both) connections have not been established.
-
Page 12: Installation Safety Warnings
Rev 1.0 Installation and Basic Operation 2.4.3 Installation Safety Warnings 1. Installation Instructions Read all installation instructions before connecting the equip- ment to the power source. 2. Over-temperature This equipment should not be operated in an area with an ambi- ent temperature exceeding the maximum recommended: 40°C (104°F). -
Page 13: Mechanical Installation
Dell -10GbE PTM Rev 1.0 CLASS 1 LASER PRODUCT and reference to the most recent laser standards: IEC 60825-1:2007/03 y EN 60825-1:2007 2.4.4 Mechanical Installation 2.4.4.1 To install the PTM 1. Make sure that there is no foreign matter or dirt in the back plane connector or in the chassis slot. -
Page 14: Chapter 3 Troubleshooting
Rev 1.0 Troubleshooting Troubleshooting As soon as a pass through module is plugged in make sure that the status LED shows green. The power LED for the pass through module shuts off: 1. Check that the there is adequate ventilation. 2. -
Page 15: Appendix A Specifications
Dell -10GbE PTM Rev 1.0 Appendix A: Specifications Table 4 - Dell 10Gb Ethernet Pass Through Module Specification Data Physical Power and Environmental Size: Maximum W X D X H 24.7 cm X 28.5 cm X 2.9 cm Power: 40.55W passive cables Weight: 1.978kg... -
Page 16: Mechanical Drawing With Dimensions
Rev 1.0 Appendix A.1: Mechanical Drawing with Dimensions Figure 7: Mechanical Drawing 24.7 23.0 23.0... -
Page 17: Appendix B Supported Optical Modules And Dcas
Dell -10GbE PTM Rev 1.0 Appendix B: Supported Optical Modules and DCAs The following cables and optical modules are approved for the Dell PTM Table 5 - DCA (Direct attached SFP+ cables) Reference Length (m) Speed Molex Custom PN K585N SFP-H10GB-CU1M 10.3125Gbps... -
Page 18: Appendix C Emc Certification Statements
Rev 1.0 Appendix C: EMC Certification Statements Table 7 lists the approved certification status per bridge in different regions of the world. Table 7 - Bridge Certification Status ICES VCCI Pass through Module P/N Class Class Class cTUVus c-Tick (Japan) (USA) (Europe) (Canada) -
Page 19: Ices Statements (Canada)
Dell -10GbE PTM Rev 1.0 Appendix C.2: ICES Statements (Canada) Class A Statement: “This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.” Appendix C.3: VCCI Statements (Japan) Class A Statement: Appendix C.3.1: Translation... - Page 20 Rev 1.0 Appendix C.4.1: Translation: “Class A Device This device is registered for EMC requirements for industrial use. The seller or buyer should be aware of this. If this type was sold or purchased by mistake, it should be replaced with a residential-use type.
-
Page 21: Appendix D Interface Connector Pinouts
Dell -10GbE PTM Rev 1.0 Appendix D: Interface Connector Pinouts Appendix D.1: SFP+ Interface Figure 8: SFP+ Connector Pinout - Rear View of Module With Pin Placement Table 8 - SFP+ Pinout Symbol Name Description VeeT Transmitter Ground (Common with Receiver Ground) TX_Fault Transmitter Fault. - Page 22 Rev 1.0 Table 8 - SFP+ Pinout Symbol Name Description VccR Receiver Power Supply VccT Transmitter Power Supply VeeT Transmitter Ground (Common with Receiver Ground) Transmitter Non-Inverted DATA in. AC Coupled. Transmitter Inverted DATA in. AC Coupled. VeeT Transmitter Ground (Common with Receiver Ground) a.