Page 1 Cisco 11500 Series Content Services Switch Hardware Installation Guide Software Version 7.40 and 7.50 March 2005 Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 526-4100 Customer Order Number: DOC-7816421=...
Page 2 You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures: •...
Page 3 CCSP, CCVP, the Cisco Square Bridge logo, Follow Me Browsing, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.; and Access Registrar, Aironet, ASIST, BPX, Catalyst, CCDA, CCDP,...
Page 5: Table Of Contents
Obtaining Additional Publications and Information xxviii Unpacking and Installing the CSS C H A P T E R Site Requirements Safety Guidelines Chassis-Lifting Guidelines for the CSS 11503 and CSS 11506 Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 6 Installation Precautions and Restrictions 1-20 Installation Precautions 1-20 Module Slot Restrictions 1-21 Unpacking a CSS Module 1-24 Installing a Module 1-24 Installing a Passive SCM in a CSS 11506 1-26 Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 7 Powering Up the CSS 2-37 Powering Down the CSS 2-38 Troubleshooting the CSS Hardware Components 2-38 Troubleshooting the CSS 11501 2-39 Troubleshooting the CSS Modules 2-40 Troubleshooting the Console Interface 2-44 Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 8 Environmental Specifications Physical Specifications CSS 11501 Bandwidth and Memory Specifications CSS 11503 and CSS 11506 Module Specifications Disk Specifications Supported Standards Transport Network Routing Gateway Application Network Utilities Network Management Cisco 11500 Series Content Services Switch Hardware Installation Guide viii 78-16421-01...
Page 9 A P P E N D I X Configuring a Modem Cabling a Modem to the CSS Regulatory Compliance and Safety Information for the Cisco 11500 Series A P P E N D I X Content Services Switch Agency Approvals...
Page 10 Installing or Replacing the Unit D-54 Use Copper Conductors Only D-56 Short-circuit Protection D-58 Blank Faceplates and Cover Panels D-61 Power Module D-66 Ground Conductor D-68 N D E X Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 11 Connecting a CSS 11503 AC Power Cord 2-29 Figure 2-13 Location of the CSS 11503 DC Power Supply Connectors 2-31 Figure 2-14 Connecting a CSS 11506 AC Power Cord 2-33 Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 12 Four Twisted-Pair Straight-Through Cable Schematic for the CSS 1000BASE-T GBIC Module Port Figure B-2 Four Twisted-Pair Crossover Cable Schematic for the CSS 1000BASE-T GBIC Module Port Figure C-1 Switch Control Module Console Connector Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 13 LEDs of the CSS 11506 Power Supply 2-49 Table A-1 AC Electrical Specifications Table A-2 DC Electrical Specifications Table A-3 Environmental Specifications Table A-4 Physical Specifications Table A-5 CSS 11501 Specifications Cisco 11500 Series Content Services Switch Hardware Installation Guide xiii 78-16421-01...
Page 14 Console Port to Modem Signals and Pinouts Table B-6 RJ-45 Management Connector Pinouts Table B-7 RJ-45 1000BASE-T GBIC Connector Pinouts Table C-1 CSS Console Port Default Settings Table D-1 Regulatory Approval Requirements Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 15: Preface
Preface This guide is intended to help you install your Cisco 11500 Series Content Services Switches (CSS), models CSS 11501, CSS 11503, and CSS 11506. It provides you with instructions for installing, cabling, and powering the CSS. Information in this guide applies to all CSSs except where noted.
Page 16: Audience
LEDs and connectors. This chapter also provides instructions for connecting the console, powering the CSS, and troubleshooting the CSS console, modules, and power supply. Appendix A, Provides specifications for the CSS and its components. Specifications Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 17 Modem to the CSS Appendix D, Provides information on regulatory compliance and Regulatory safety pertaining to the CSS. Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Cisco 11500 Series Content Services Switch Hardware Installation Guide xvii 78-16421-01...
Page 18: Related Documentation
Configuring sticky cookies with a sticky • overview and advanced load-balancing method using cookies Finding information in the CSS documentation • with a task list Troubleshooting the boot process • Cisco 11500 Series Content Services Switch Hardware Installation Guide xviii 78-16421-01...
Page 19 Address Resolution Protocol (ARP) Routing Information Protocol (RIP) • Internet Protocol (IP) • Open Shortest Path First (OSPF) protocol • Cisco Discovery Protocol (CDP) • Dynamic Host Configuration Protocol (DHCP) • relay agent Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 20 Cisco Content Services This guide describes how to perform CSS Switch Redundancy redundancy configuration tasks, including: Configuration Guide VIP and virtual interface redundancy • Adaptive session redundancy • Box-to-box redundancy • Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 21 Cisco Content Services This guide explains how to use the Device Switch Device Management user interface, an HTML-based Management User’s Guide Web-based application that you use to configure and manage your CSS. Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 22: Symbols And Conventions
If you need translations of the safety warnings, refer to the Appendix D, Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch. Cisco 11500 Series Content Services Switch Hardware Installation Guide xxii 78-16421-01...
Page 23: Obtaining Documentation
Obtaining Documentation Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several ways to obtain technical assistance and other technical resources. These sections explain how to obtain technical information from Cisco Systems. Cisco.com You can access the most current Cisco documentation at this URL: http://www.cisco.com/univercd/home/home.htm...
Page 24: Ordering Documentation
170 West Tasman Drive San Jose, CA 95134-9883 We appreciate your comments. Cisco Product Security Overview Cisco provides a free online Security Vulnerability Policy portal at this URL: http://www.cisco.com/en/US/products/products_security_vulnerability_policy.ht From this site, you can perform these tasks: • Report security vulnerabilities in Cisco products.
Page 25: Reporting Security Problems In Cisco Products
• Register to receive security information from Cisco. • A current list of security advisories and notices for Cisco products is available at this URL: http://www.cisco.com/go/psirt If you prefer to see advisories and notices as they are updated in real time, you...
Page 26: Obtaining Technical Assistance
URL: http://www.cisco.com/techsupport Access to all tools on the Cisco Technical Support Website requires a Cisco.com user ID and password. If you have a valid service contract but do not have a user ID or password, you can register at this URL: http://tools.cisco.com/RPF/register/register.do...
Page 27: Submitting A Service Request
For S1 or S2 service requests or if you do not have Internet access, contact the Cisco TAC by telephone. (S1 or S2 service requests are those in which your production network is down or severely degraded.) Cisco TAC engineers are assigned immediately to S1 and S2 service requests to help keep your business operations running smoothly.
Page 28: Obtaining Additional Publications And Information
Cisco Press publishes a wide range of general networking, training and • certification titles. Both new and experienced users will benefit from these publications. For current Cisco Press titles and other information, go to Cisco Press at this URL: http://www.ciscopress.com Packet magazine is the Cisco Systems technical user magazine for •...
Page 29 Preface Obtaining Additional Publications and Information Internet Protocol Journal is a quarterly journal published by Cisco Systems • for engineering professionals involved in designing, developing, and operating public and private internets and intranets. You can access the Internet Protocol Journal at this URL: http://www.cisco.com/ipj...
Page 30 Preface Obtaining Additional Publications and Information Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 31: Chapter 1 Unpacking And Installing The Css
• If the Product is Damaged • Preinstallation Requirements • Installing the CSS 11501 • Installing the CSS 11503 • Installing the CSS 11506 • Installing a CSS Module • Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 32: Site Requirements
When you install the CSS, observe all of the caution and warning statements in the installation procedures. For warning translations, refer to Appendix D, Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch. Read the following guidelines to help ensure your safety and protect the equipment.
Page 33: Chassis-Lifting Guidelines For The Css 11503 And Css 11506
If you remove the fan assembly and power modules to lighten the chassis, be • sure to provide anti-static mats or bags to protect the removed components. Be careful when you remove the power modules—they are heavy. Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 34: Electrical Safety
Chapter 1 Unpacking and Installing the CSS Safety Guidelines Cisco Systems recommends that you leave line cards installed in the chassis. • Removing line cards greatly increases the chances of damage to the chassis or components, and introduces the possibility that you will unintentionally change the configuration.
Page 35 Read the installation instructions before you connect the system to its power Warning source. Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 36: Specifications For Cisco 11500 Series Power Supplies
CSS 11506 Voltage DC -48.0 to -60.0 VDC -48.0 to -60.0 VDC Current DC (maximum) 9 Amps 18 Amps Power Consumption 430VA 860VA (maximum) Heat Dissipation 1468 BTU/hr 2936 BTU/hr Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 37: Power Guidelines For Dc Systems (Css 11503 And Css 11506)
Once you complete the installation, you need a console terminal (or equivalent) that runs at 9600 baud to enter console commands (refer to Chapter 2, Cabling and Troubleshooting the CSS). Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 38: Shipment Contents
Claim Certificates will be included in the accessory kit. If you cannot locate the Standard software license key or a license key Note Claim Certificate in the accessory kit, call the Cisco Licensing department in the Technical Assistance Center at (800) 553-2447 or email them at [email protected].
Page 39: Unpacking The Css
CSS later. Check the configuration of the CSS and the accessories against the items listed on the packing slip. Report any discrepancies as described in “If the Product is Damaged” section. Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 40: If The Product Is Damaged
Upon receipt of this information, you will be provided with service instructions, or a Return Material Authorization (RMA) number and shipping information. To obtain assistance, refer to “Preface”, the “Obtaining Documentation” section. Cisco 11500 Series Content Services Switch Hardware Installation Guide 1-10 78-16421-01...
Page 41: Preinstallation Requirements
The minimum clearance requirement is 2 inches (10 cm) of air flow space on • both sides of the chassis. Ensure that the CSS is reliably grounded to earth. Cisco Systems recommends • that you do not use power strips or extension cords to connect the CSS to the power source.
Page 42: Installing The Css 11501
Attach the rubber feet, provided in the accessory kit, to each bottom corner of the CSS. All cables connect to the front of the chassis with the exception of the power cord. Note Cisco 11500 Series Content Services Switch Hardware Installation Guide 1-12 78-16421-01...
Page 43: Installing A Css 11501 As A Rackmounted Unit
Raise the CSS to the installation height and align the screw holes on the mounting bracket with the holes on the equipment rack. Secure each mounting bracket to each side of the rack. Cisco 11500 Series Content Services Switch Hardware Installation Guide 1-13 78-16421-01...
Page 44: Installing The Css 11503
Attach the rubber feet, provided in the accessory kit, to each bottom corner of the CSS. All cables connect to the front of the unit with the exception of the power cord. Note Cisco 11500 Series Content Services Switch Hardware Installation Guide 1-14 78-16421-01...
Page 45: Installing A Css 11503 As A Rackmounted Unit
LINK S W I T C PCM CIA SLO T 1 SLO T 0 CON SOL E LINK DPL X LINK DPL X LINK DPL X LINK DPL X Cisco 11500 Series Content Services Switch Hardware Installation Guide 1-15 78-16421-01...
Page 46: Figure 1-3 Mid-Mounting The Mounting Brackets On The Css 11503
Raise the CSS to the installation height and align the screw holes on the mounting bracket with the holes on the equipment rack. Secure each mounting bracket to each side of the rack. Cisco 11500 Series Content Services Switch Hardware Installation Guide 1-16 78-16421-01...
Page 47: Installing The Css 11506
10 0-2 40 V 5A 50 -60 10 0-2 40 V 5A 50 -60 This section covers: Mid-Mounting the CSS 11506 Mounting Brackets • Rack-Mounting the CSS 11506 Chassis • Cisco 11500 Series Content Services Switch Hardware Installation Guide 1-17 78-16421-01...
Page 48: Mid-Mounting The Css 11506 Mounting Brackets
Repeat steps 1 through 3 to reposition the other mounting bracket on the other side of the chassis. To install the chassis in a rack, proceed to the “Rack-Mounting the CSS 11506 Chassis” section. Cisco 11500 Series Content Services Switch Hardware Installation Guide 1-18 78-16421-01...
Page 49: Rack-Mounting The Css 11506 Chassis
This information applies to the CSS modules only. If you received an additional module at a later time, it comes with a reference sheet providing information on the module and how to install it. Cisco 11500 Series Content Services Switch Hardware Installation Guide 1-19 78-16421-01...
Page 50: Installation Precautions And Restrictions
Installing a CSS Module Installation Precautions and Restrictions This section includes background material related to installing a module into the CSS chassis. Cisco Systems recommends that you read the topics in this section before installing a module. Installation Precautions Read and observe the following precautionary information prior to servicing the CSS.
Page 51: Module Slot Restrictions
CSS 11506 Chassis Slot Restriction Slot Number Slot Usage Initial active Switch Control Module (SCM) Initial passive SCM or I/O module I/O module I/O module I/O module I/O module Cisco 11500 Series Content Services Switch Hardware Installation Guide 1-21 78-16421-01...
Page 52: Figure 1-6 Fully-Configured Css 11503
SLO T 1 SLO T 0 CON SOL E LINK DPL X LINK DPL X LINK DPL X LINK DPL X Slot location 1 Slot location 3 Slot location 2 Cisco 11500 Series Content Services Switch Hardware Installation Guide 1-22 78-16421-01...
Page 53: Figure 1-7 Fully-Configured Css 11506
10 0-2 40 V 5A 50 -60 10 0-2 40 V 5A 50 -60 Slot location 1 Slot location 4 Slot location 2 Slot location 5 Slot location 3 Slot location 6 Cisco 11500 Series Content Services Switch Hardware Installation Guide 1-23 78-16421-01...
Page 54: Unpacking A Css Module
To install a module into the CSS chassis, see the “Installing a Module” section. Installing a Module You must power down the CSS before installing or removing a Switch Module in Caution a CSS 11506. Cisco 11500 Series Content Services Switch Hardware Installation Guide 1-24 78-16421-01...
Page 55: Figure 1-8 Installing A Module Into A Css Chassis
Close both ejectors simultaneously to seat the module connector into the backplane. Using a Phillips screwdriver, tighten the spring-loaded screws on the front of the module faceplate. Reboot the chassis to activate the module. Cisco 11500 Series Content Services Switch Hardware Installation Guide 1-25 78-16421-01...
Page 56: Installing A Passive Scm In A Css 11506
Extend both ejectors simultaneously to seat the module connector into the backplane. Using a Phillips screwdriver, tighten the spring-loaded screws on the front of the module faceplate. Cisco 11500 Series Content Services Switch Hardware Installation Guide 1-26 78-16421-01...
Page 57: Figure 1-9 Installing A Pcmcia Cover On An Scm
To copy the boot configuration from the active SCM to the passive SCM, use the passive sync command in boot configuration mode. For more information, refer to the Cisco Content Services Switch Administration Guide. Cisco 11500 Series Content Services Switch Hardware Installation Guide...
Page 58 Chapter 1 Unpacking and Installing the CSS Installing a CSS Module Cisco 11500 Series Content Services Switch Hardware Installation Guide 1-28 78-16421-01...
Page 59: Chapter 2 Cabling And Troubleshooting The Css
Connecting the Console • Connecting the Chassis to Ground • Connecting the Power Cord • Powering Up the CSS • Powering Down the CSS • Troubleshooting the CSS Hardware Components • Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 60: Cabling The Css 11501
RJ-45 10-Mbps half-duplex Ethernet management connector RJ-45 RS-232 Diag connector (reserved for field service diagnostic use only). • Eight auto-sensing 10/100-Mbps Ethernet (10BASE-T/100BASE-TX) interfaces • Optional integrated Secure Sockets Layer (SSL) termination • Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 61 Two status module LEDs indicating power and device readiness • • Link/Act and Duplex LEDs for the Ethernet Management port Link/Act and Duplex LEDs for each Ethernet port • Link/Act LED for the SFP GBIC • Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 62: Css 11501 Connectors And Leds
1. The Ethernet Link/Act LED and Duplex LED are located at the top of each RJ-45 Ethernet connector and are not visible in this illustration. Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 63: Table 2-1 Css 11501 Led Descriptions
Ethernet Port is operating at full duplex. Management Port Link/Act Green No link established. for Ethernet Port Link established but no activity. Blinking Link established with transmit or receive activity. Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 64: Cabling The Css 11503 And Css 11506 Modules
For information on the connector pinouts, refer to Appendix B, Cable Connector Pinouts. If you encounter problems with the modules in the CSS 11503 and CSS 11506, see the “Troubleshooting the CSS Modules” section later in this chapter. Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 65: Css 11503 And Css 11506 Module Overview
Performance increases incrementally as you add modules, and the modules balance the overall traffic load. The Cisco 11506 is a five-rack unit, supporting six-slots, with 40-Gbps • aggregate throughput. The CSS 11506 requires at least one Switch Control Module (SCM) and may be configured with a second SCM in standby mode for redundancy.
Page 66 The CSS 11503 supports a maximum of two SSL modules and the CSS 11506 supports a maximum of four SSL modules. For information on SSL commands and functions, refer to the Cisco Content Services Switch SSL Configuration Guide.
Page 67: Figure 2-2 Css 11503 Content Services Switch
SLOT 0 CON SOLE LINK DPLX LINK DPLX LINK DPLX LINK DPLX Slot 1 for the SCM only Slot 3 for an I/O module Slot 2 for an I/O module Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 68: Figure 2-3 Css 11506 Content Services Switch
Slot 6 Switch Modules in slots 7 and 8 Power supplies 1, 2, and 3 1. Slots 3 through 6 are for I/O modules, including SAMs and SSL modules. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-10 78-16421-01...
Page 69: Switch Control Module Connectors And Leds
The Switch Control Module contains the following connectors and slots: 1 RJ-45 10-Mbps half-duplex Ethernet management connector. • 1 RJ-45 RS-232 Console connector. • 1 RJ-45 RS-232 Diag connector (reserved for field service diagnostic use • only). Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-11 78-16421-01...
Page 70 The SCM front panel LEDs indicate module and configuration status: Two status module LEDs indicating power and module readiness • Link/Act and Duplex LEDs for the Ethernet management port • Link LEDs for each SFP GBIC • Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-12 78-16421-01...
Page 71: Figure 2-4 Switch Control Module Connectors And Leds
SFP GBIC (one of two) Recessed button (reserved for field service use only) Link LED for the associated SFP GBIC on the left Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-13 78-16421-01...
Page 72: Table 2-2 Switch Control Module Led Descriptions
Link Green There is no link. for each Gigabit The link exists and Ethernet Port synchronization is achieved. Blinking The link is established with transmit or receive activity. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-14 78-16421-01...
Page 73: Fast Ethernet Module Connectors And Leds
8 (connector 7 is shown directly shown directly above it) below it) Link LED (on each connector) Spring-loaded screw (one of two) Duplex LED (on each Ejector (one of two) connector) Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-15 78-16421-01...
Page 74: Figure 2-6 16-Port Fast Ethernet Module Connectors And Leds
16 (connector 15 is shown directly shown directly above it) below it) Link LED (on each connector) 5 Spring-loaded screw (one of two) Duplex LED (on each Ejector (one of two) connector) Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-16 78-16421-01...
Page 75: Gigabit Ethernet Module Connectors And Leds
Because invisible radiation may be emitted from the aperture of the port when no fiber cable is connected, avoid exposure to radiation and do not stare into open apertures. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-17 78-16421-01...
Page 76: Figure 2-7 Gigabit Ethernet Module Connectors And Leds
Bicolor status LED (green and Link LED (next to its red) corresponding SFP GBIC) Amber status LED Spring-loaded screw (one of two) SFP GBIC (one of two) Ejector (one of two) Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-18 78-16421-01...
Page 77: Table 2-4 Gigabit Ethernet Module Led Descriptions
See the left status LED for indication. Link Green There is no link. The link exists and synchronization is achieved. Blinking The link is established with transmit or receive activity. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-19 78-16421-01...
Page 78: Session Accelerator Module Leds
Session Accelerator Module LEDs ST AT US ST AT US Bicolor status LED (green and red) 3 Spring-loaded screw (one of two) Amber status LED Ejector (one of two) Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-20 78-16421-01...
Page 79: Secure Socket Layer (Ssl) Module Leds
The front panel LEDs on the module indicate its operational status. The SSL module has no connectors. The CSS 11503 supports a maximum of two SSL modules and the CSS 11506 supports a maximum of four SSL modules. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-21 78-16421-01...
Page 80: Figure 2-9 Ssl Module Leds
The module is running power-up self test. (right) Slow blink The module is offline and active. Solid The module is online and not active. See the left status LED for indication. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-22 78-16421-01...
Page 81: Connecting The Console
Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-23 78-16421-01...
Page 82: Tools And Supplies
Burndy no. YA6CL2TC10 • wish to use a lug other than the one supplied. If you need a lug for the facility end of the ground wire, you must supply it. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-24 78-16421-01...
Page 83: Attaching The Grounding Cable
13/16 inch (2 cm) Panduit no. LCC6-10A-L (long barrel) 1 1/16 inch (2.7 cm) Thomas & Betts no. 256-30695-1183(*4*) 3/4 inch (1.9 cm) Burndy no. YA6CL2TC10 7/8 inch (2.2 cm) Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-25 78-16421-01...
Page 84: Figure 2-10 Attaching Grounding Wire To Grounding Lug
Attach the grounding lug to an appropriate grounding point at your site. Proceed to the “Connecting the Power Cord” section. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-26 78-16421-01...
Page 85: Connecting The Power Cord
Plug the AC power cord connector into the CSS power connector, as shown Figure 2-11. Figure 2-11 Connecting a CSS 11501 AC Power Cord AC power connector Power switch Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-27 78-16421-01...
Page 86: Connecting A Css 11503 Power Cord
At the rear of the chassis, ensure that the CSS power switch is in the O (off) position. Plug the AC power cord connector into the CSS power connector, as shown Figure 2-12. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-28 78-16421-01...
Page 87: Figure 2-12 Connecting A Css 11503 Ac Power Cord
See the “Powering Up the CSS” section to power on the CSS. The CSS 11503 power supply is autosensing for voltage and frequency, and it Note requires no additional modifications. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-29 78-16421-01...
Page 88: Connecting A Css 11503 Dc Power Cord
(SELV) requirements in UL1950, CSA 950 3rd Edition, EN 60950, and IEC950, can be connected to a Cisco 11503 system. This requirement ensures that in a catastrophic power source fault condition, hazardous voltages are not present on power terminals and connectors.
Page 89: Figure 2-13 Location Of The Css 11503 Dc Power Supply Connectors
Do not consolidate the end of a conductor by soft soldering prior to installation. Install the wires into the appropriate connector. Make sure that the non-insulated part of each wire is 9 mm (0.35 inches) in length. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-31 78-16421-01...
Page 90: Connecting A Css 11506 Power Cord
The following sections provide information for connecting an AC or DC power cords to a CSS 11506. Connecting a CSS 11506 AC Power Cord • Connecting a CSS 11506 DC Power Cord • Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-32 78-16421-01...
Page 91: Connecting A Css 11506 Ac Power Cord
See the “Powering Up the CSS” section to power on the CSS. The CSS 11506 power supplies are autosensing for voltage and frequency, and Note they require no additional modifications. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-33 78-16421-01...
Page 92: Connecting A Css 11506 Dc Power Cord
(SELV) requirements in UL1950, CSA 950 3rd Edition, EN 60950, and IEC950, can be connected to a Cisco 11506 system. This requirement ensures that in a catastrophic power source fault condition, hazardous voltages are not present on power terminals and connectors.
Page 93: Figure 2-15 Location Of Css 11506 Dc Power Supply Connectors
Reversed polarity can cause damage to the DC power supply and can create a dangerous shock hazard. Do not consolidate the end of a conductor by soft soldering prior to installation. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-35 78-16421-01...
Page 94: Table 2-10 Css 11506 To Dc Power Source Cabling
Switch on each circuit breaker that services each DC circuit. To check the DC power connection, see the “Checking the DC Power Connection (CSS 11503 and CSS 11506)” section. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-36 78-16421-01...
Page 95: Checking The Dc Power Connection (Css 11503 And Css 11506)
Power on all of the supplies in the CSS. The AC OK and DC OK LEDs light up on each power supply. If either LED remains unlit, see the “Troubleshooting the CSS Power Supply” section later in this chapter. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-37 78-16421-01...
Page 96: Powering Down The Css
The CSS starts the boot process. For information concerning the boot process on the Cisco 11500 series CSS, refer to the Cisco Content Services Switch Getting Started Guide. Powering Down the CSS To shut down the CSS gracefully and avoid introducing lost or fragmented files, always use the shutdown command prior to removing power from the CSS.
Page 97: Troubleshooting The Css 11501
- the boot.log file. Obtain technical assistance. NOT STARTING UP Refer to “Preface”. For information on log files, refer to the Cisco Content Services Switch Administration Guide. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-39 78-16421-01...
Page 98: Troubleshooting The Css Modules
CSS 11503 and CSS 11506. Always power down the CSS prior to removing or installing a module. Caution Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-40 78-16421-01...
Page 99: Table 2-12 Troubleshooting The Css Modules
Remove and replace the module. Refer to ONDM: Port C Path Failure the reference sheet that comes with the %s, turning off Focus-C replacement module. Port. Reboot the CSS to boot the module. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-41 78-16421-01...
Page 100 For a CSS 11503, replace the chassis. • • For a CSS 11506, replace the fan module. Refer to the reference sheet that comes with the replacement module. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-42 78-16421-01...
Page 101 CSS software ADI file to install on the disk. If you archived an offline version of your CSS running-config file, copy it back onto the CSS. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-43 78-16421-01...
Page 102: Troubleshooting The Console Interface
CSS to you want. distinguish between different commands and options. Random characters are lost. Set the flow command on the console to XON/XOFF. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-44 78-16421-01...
Page 103: Troubleshooting The Css Power Supply
There is no power to the power supply. Ensure that the CSS 11501 has power. • Check the power switch, power cord, and power source. The power supply failed, obtain technical assistance. • Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-45 78-16421-01...
Page 104 This message is displayed only if the logging level is set to the Info-6 or Debug-7 Note level. A CSS 11506 can contain a maximum of three power supplies, but it requires two functioning power supplies to guarantee service. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-46 78-16421-01...
Page 105: Figure 2-16 Location Of The Css 11506 Power Supplies
CHMGR: Cannot locate power supply: PSnumber. The PSnumber variable indicates which power supply cannot be found or has failed. When this message occurs, view the LEDs on the power supply. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-47 78-16421-01...
Page 106: Figure 2-17 Css 11506 Ac Power Supply Leds
PS 3 10 0- 24 0V 5A 50 -6 0 -4 8/ -6 0V 10 /8 A Power Supply LEDs: I/P OK and DC OK Terminal block Power switch Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-48 78-16421-01...
Page 107: Table 2-14 Leds Of The Css 11506 Power Supply
The power supply failed. Remove and replace the power supply. Refer to the reference sheet that comes with the replacement supply. After you install the power supply, the CSS automatically brings the power supply into service. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-49 78-16421-01...
Page 108: Troubleshooting The Css Fans
CSS 11501 starts to overheat, the following message appears: Temperature has reached x celsius for slot number The x variable indicates the temperature of the CSS 11501. When a fan failure occurs, obtain technical assistance. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-50 78-16421-01...
Page 109: Troubleshooting The Css 11503 Chassis Fans
If the power supply fan fails, the following message appears: CHMGR: Power Supply Fan Failure. When a fan failure occurs, you must replace the CSS chassis. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-51 78-16421-01...
Page 110: Troubleshooting The Css 11506 Fan Module
When a fan failure occurs, you must replace the fan module to prevent the CSS modules from overheating. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-52 78-16421-01...
Page 111: Appendix
Electrical Specifications • Environmental Specifications • Physical Specifications • • CSS 11501 Bandwidth and Memory Specifications CSS 11503 and CSS 11506 Module Specifications • Disk Specifications • Supported Standards • Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 112: Electrical Specifications
Voltage DC -48.0 to -60.0 VDC -48.0 to -60.0 VDC Current DC (maximum) 9 Amps 18 Amps Power Consumption 430 VA 860 VA (maximum) Heat Dissipation 1468 BTU/hr 2936 BTU/hr Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 113: Environmental Specifications
Not applicable Noise G is the unit of acceleration due to gravity, where 1 G equals 32.17 ft/sec Note (9.81 m/sec Grms is the root mean square value of acceleration. Note Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 114: Physical Specifications
Chassis Weight Fully 18.0 lbs. 33.3 lbs. 57.7 lbs. Configured (base system containing (base system containing one SCM and two I/O two power supplies, modules) one SCM, and five I/O modules) Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 115: Css 11501 Bandwidth And Memory Specifications
144 MB default or 288 MB optional (RDRAM) (128 MB or 256 MB of usable (128 MB or 256 MB of usable memory, respectively) memory, respectively) SSL Module Memory 512 MB SDRAM 512 MB SDRAM Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 116: Disk Specifications
The CSS supports the following standards: Transport • Network • Routing • Gateway • Application • Network Utilities • Network Management • Transport The CSS supports the following transport standards: • • Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 117: Network
The CSS supports Network Address Translation (NAT), per RFC 1631 gateway standards Application The CSS supports the following application standards: HTTP 1.0, HTTP 1.1 • TELNET • FTP, TFTP • • Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 118: Network Utilities
RADIUS Client • TACACS+ Client • HTTP Client • FTP Daemon • SNTP • Network Management The CSS supports the following network management standards: SNMP v1 • SNMP v2c • Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 119: Appendix
CSS 11501, CSS 11503, and CSS 11506: RJ-45 Fast Ethernet Connector Pinouts • RJ-45 RS-232 Console Port Pinouts • RJ-45 Management Connector Pinouts • • RJ-45 1000BASE-T GBIC Connector Pinouts Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 120: Rj-45 Fast Ethernet Connector Pinouts
Ethernet-type cable. Table B-1 RJ-45 Fast Ethernet Connector Pinouts RJ-45 Fast Ethernet Pin Signal Name Numbers RX + RX - TX + Unconnected Unconnected TX - Unconnected Unconnected Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 121: Rj-45 Rs-232 Console Port Pinouts
The following sections provide the pinouts for: Connecting the Console Port to a PC • Connecting the Console Port to a Terminal • Connecting the Console Port to a Modem • Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 122: Connecting The Console Port To A Pc
RJ-45 Rollover DB-9 DTE Console Port to Cable to RJ-45 Adapter to PC Console RJ-45 Rollover DTE Adapter Console PC Console Port Signal Cable Pinouts Pinouts Device Pinouts Device Signal Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 123: Connecting The Console Port To A Terminal
Console Port to Terminal Signals and Pinouts RJ-45 Rollover DB-25 DTE Console Port to Cable to RJ-45 Adapter to Console RJ-45 Rollover DTE Adapter Terminal Terminal Port Signal Cable Pinouts Pinouts Pinouts Device Signal Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 124: Connecting The Console Port To A Modem
Console Port to Modem Signals and Pinouts RJ-45 Rollover DB-25 DCE Console Port to Cable to RJ-45 Adapter to Console RJ-45 Rollover DCE Adapter Modem Modem Port Signal Cable Pinouts Pinouts Pinouts Device Signal Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 125: Rj-45 Management Connector Pinouts
CSS 11501 front panel and the CSS 11503 or CSS 11506 SCM. Table B-6 RJ-45 Management Connector Pinouts Signal Name Pin Number TX + TX - RX + Unconnected Unconnected RX - Unconnected Unconnected Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 126: Rj-45 1000Base-T Gbic Connector Pinouts
1000BASE-T GBIC module port. When connecting the CSS to servers, workstations, and routers, use the straight-through cable. When connecting the CSS to switches and repeaters, use the crossover cable. Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 127: Figure B-1 Four Twisted-Pair Straight-Through Cable Schematic For The Css 1000Base-T Gbic
1 TP0+ 2 TPO- 2 TP0- 3 TP1+ 3 TP1+ 6 TP1- 6 TP1- 4 TP2+ 4 TP2+ 5 TP2- 5 TP2- 7 TP3+ 7 TP3+ 8 TP3- 8 TP3- Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 128 Appendix B Cable Connector Pinouts RJ-45 1000BASE-T GBIC Connector Pinouts Cisco 11500 Series Content Services Switch Hardware Installation Guide B-10 78-16421-01...
Page 129: Appendix
Hyperterm. If you connect the modem to the COM port on a PC, you need the following cable and connectors (see Appendix B, Cable Connector Pinouts): RJ-45-to-RJ-45 rolled cable • RJ-45-to-DB-25 modem adapter • DB-9-to-RJ-45 terminal adapter • Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 130: Cabling A Modem To The Css
ST AT US DU PL EX GE 1 LI NK GE 2 LI NK PC MC IA SL OT 1 SL OT 0 C O N SO LE Console connector Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 131 CSS before the CSS logs it out. By default, the timeout is disabled. Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 132 Appendix C Connecting a Modem to the CSS Cabling a Modem to the CSS Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-16421-01...
Page 133: Appendix
Content Services Switch This appendix provides international agency compliance information applicable to the Cisco Content Services Switches (CSS) 11501, 11503, and 11506. This appendix also provides translations of safety warnings. Use the information in this appendix in conjunction with the information contained in the CSS documentation set, listed in the “Related Documentation”...
Page 134: Agency Approvals
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Agency Approvals Agency Approvals Table D-1 lists the regulatory approval requirements for the Cisco 11500 Series CSSs. Table D-1 Regulatory Approval Requirements Regulatory Requirement Category...
Page 135: Fcc Class A Compliance Notice (United States
You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or...
Page 136: Fcc Compliance Information Statement (United States
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Agency Approvals FCC Compliance Information Statement (United States) Cisco 11500 Series Content Services Switches (CSS 11503 and CSS 11506) This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
Page 137: Ices-003 Class A Compliance Notice (Canada
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Agency Approvals ICES-003 Class A Compliance Notice (Canada) English Statement of Compliance This class A digital apparatus complies with Canadian ICES-003. French Statement of Compliance...
Page 138: Declaration Of Conformity With Regard To The Directives 73/23/Eec And 89/336/Eec As Amended By Directive 93/68/Eec
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Agency Approvals Declaration of Conformity with Regard to the Directives 73/23/EEC and 89/336/EEC as amended by Directive 93/68/EEC English: This equipment is in compliance with the essential requirements and other provisions of Directives 73/23/EEC and 89/336/EEC as amended by Directive 93/68/EEC.
Page 139: Cispr 22 Class A Warning
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Agency Approvals Português: Este equipamento satisfaz os requisitos essenciais e outras provisões das Directivas 73/23/EEC e 89/336/EEC, conforme amendados pela Directiva 93/68/EEC. Cisco 11500 Series CSS Suomalainen: Tämä...
Page 140: Vcci Class A Warning
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Agency Approvals VCCI Class A Warning Warning This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise.
Page 141 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Agency Approvals Avvertenza Il presente è un prodotto di Classe A ai sensi della norma del Voluntary Control Council for Interference by Information Technology Equipment (VCCI). Se questa apparecchiatura viene usata in ambito domestico, è...
Page 142: Class A Warning For Taiwan And Other Traditional Chinese Markets
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Agency Approvals Class A Warning for Taiwan and Other Traditional Chinese Markets This is a Class A Information Product, when used in residential environment, it...
Page 143: Safety Requirements
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Safety Requirements Safety Requirements This section identifies safety requirements with which Cisco Content Services Switches comply. UL 60950 Third Edition - Safety of Information Technology Equipment.
Page 144: Laser Safety
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Safety Requirements Mexico NOM-019-SCFI-1998, Safety of Data Processing Equipment. Australia ACA TS001 1997 Test Report and Statement of Compliance AS/NZS3260 incorporating Amendment 1, 2, 3, and 4.
Page 145: Translated Safety Warnings
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Translated Safety Warnings This section repeats, in multiple languages, the warnings contained in this publication. In addition, this section contains translated warnings that can be used...
Page 146 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Varoitus TÄRKEITÄ TURVALLISUUSOHJEITA Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin.
Page 147 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Avvertenza IMPORTANTI ISTRUZIONI SULLA SICUREZZA Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti.
Page 148 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings ¡Advertencia! INSTRUCCIONES IMPORTANTES DE SEGURIDAD Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de...
Page 149 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Cisco 11500 Series Content Services Switch Hardware Installation Guide D-17 78-16421-01...
Page 150 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e...
Page 151 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Cisco 11500 Series Content Services Switch Hardware Installation Guide D-19 78-16421-01...
Page 152 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Cisco 11500 Series Content Services Switch Hardware Installation Guide D-20 78-16421-01...
Page 153 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Cisco 11500 Series Content Services Switch Hardware Installation Guide D-21 78-16421-01...
Page 154: Battery Handling
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Battery Handling Warning There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommended by the manufacturer.
Page 155 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Aviso Existe perigo de explosão se a bateria for substituída incorrectamente. Substitua a bateria por uma bateria igual ou de um tipo equivalente recomendado pelo fabricante.
Page 156: Invisible Laser Radiation
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Invisible Laser Radiation Warning Invisible laser radiation present. Statement 1016 Waarschuwing Onzichtbare laserstraling aanwezig. Varoitus Näkymättömiä lasersäteitä. Attention Rayonnement laser actif mais invisible.
Page 157: Jewelry Removal Warning
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Jewelry Removal Warning Warning Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld the metal object to the terminals.
Page 158 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Advarsel Fjern alle smykker (inkludert ringer, halskjeder og klokker) før du skal arbeide på utstyr som er koblet til kraftledninger. Metallgjenstander som er koblet til kraftledninger og jord blir svært varme og kan forårsake alvorlige...
Page 159: Installation Instructions
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Installation Instructions Read the installation instructions before connecting the system to the power Warning source. Statement 1004 Waarschuwing Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron aansluit.
Page 160: Invisible Laser Radiation Warning
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Varning! Läs installationsanvisningarna innan du kopplar systemet till strömförsörjningsenheten. Invisible Laser Radiation Warning Warning Because invisible laser radiation may be emitted from the aperture of the port when no cable is connected, avoid exposure to laser radiation and do not stare into open apertures.
Page 161: Equipment Installation
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Warnung Aus der Öffnung des Ports kann unsichtbare Laserstrahlung austreten, wenn kein Kabel angeschlossen ist. Kontakt mit Laserstrahlung vermeiden und nicht in offene Öffnungen blicken.
Page 162 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Attention Il est vivement recommandé de confier l'installation, le remplacement et la maintenance de ces équipements à des personnels qualifiés et expérimentés.
Page 163 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Aviso Somente uma equipe treinada e qualificada tem permissão para instalar, substituir ou dar manutenção a este equipamento. Advarsel Kun uddannede personer må installere, udskifte komponenter i eller servicere dette udstyr.
Page 164: Two Person Lifting Requirement
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Two Person Lifting Requirement Warning Two people are required to lift the chassis. To prevent injury, keep your back straight and lift with your legs, not your back. Statement 164 Waarschuwing Er zijn twee personen nodig om het chassis op te tillen.
Page 165: Chassis Lifting Warning
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings ¡Advertencia! Se requieren dos personas para elevar el chasis. Para evitar lesiones, mantenga su espalda en posición recta y levante con sus piernas, no con su espalda.
Page 166 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Attention Il faut deux personnes pour soulever le châssis. Le saisir par son rebord inférieur et soulever des deux mains. Pour éviter tout trauma de la région lombaire, garder le dos droit et soulever la charge en redressant les jambes.
Page 167 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Aviso São necessárias duas pessoas para levantar o chassis. Agarre o chassis imediatamente abaixo da margem inferior, e levante-o com ambas as mãos.
Page 168 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Aviso São necessárias duas pessoas para suspender o chassi. Segure o chassi por baixo das extremidades da parte inferior e suspenda-o com as duas mãos.
Page 169 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Cisco 11500 Series Content Services Switch Hardware Installation Guide D-37 78-16421-01...
Page 170 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Cisco 11500 Series Content Services Switch Hardware Installation Guide D-38 78-16421-01...
Page 171: Chassis Installation Warning
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Chassis Installation Warning Warning At least three people are required to mount the chassis in the equipment rack: two people are needed to hold the chassis in place while a third person tightens the mounting screws.
Page 172 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings ¡Advertencia! Se necesitan al menos tres personas para montar el chasis sobre el soporte del equipo: dos personas para mantener el chasis en su lugar y una tercera persona para ajustar los tornillos de montaje.
Page 173: Work During Lightning Activity
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Work During Lightning Activity Do not work on the system or connect or disconnect cables during periods of Warning lightning activity. Statement 1001...
Page 174: Disconnect Device
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Disconnect Device A readily accessible two-poled disconnect device must be incorporated in the Warning fixed wiring. Statement 1022 Waarschuwing Er moet een gemakkelijk toegankelijke, tweepolige stroomverbreker opgenomen zijn in de vaste bedrading.
Page 175 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Aviso Deverá incorporar-se um dispositivo de desconexão de dois pólos de acesso fácil, na instalação eléctrica fixa. Advertencia El cableado fijo debe incorporar un dispositivo de desconexión de dos polos y de acceso fácil.
Page 176 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Cisco 11500 Series Content Services Switch Hardware Installation Guide D-44 78-16421-01...
Page 177: Cisco 11500 Power Source
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Cisco 11500 Power Source Warning Only a DC power source that is isolated from AC mains with reinforced insulation, and that complies with the other safety extra-low voltage (SELV) requirements in UL950, CSA 950, EN 60950, and IEC950, can be connected to a Cisco 11500 system.
Page 178 Bare likestrømskilder som er isolert fra vekselstrømledninger med ekstra isolasjon, og som oppfyller andre sikkerhetskrav for lavspenning (SELV) i UL950, CSA 950, EN 60950 og IEC950 kan kobles til et Cisco 11500-system. Disse kravene sikrer at hvis det skulle oppstå en katastrofal feil i en strømkilde, er det ikke farlig spenning tilstede på...
Page 179: Dc Power Supply Warning
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings DC Power Supply Warning Warning The illustration shows the DC power supply terminal block. Wire the DC power supply using the appropriate lugs at the wiring end, or with no lugs, as illustrated.
Page 180 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Avvertenza L’illustrazione mostra la morsettiera dell alimentatore CC. Cablare l’alimentatore CC usando i connettori adatti all’estremità del cablaggio, oppure senza capicorda, come illustrato. La corretta sequenza di cablaggio è...
Page 181: More Than One Power Supply
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings More Than One Power Supply This unit might have more than one power supply connection. All connections Warning must be removed to de-energize the unit. Statement 1028 Waarschuwing Deze eenheid kan meer dan één stroomtoevoeraansluiting bevatten.
Page 182 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Varoitus Tässä laitteessa voi olla useampia kuin yksi virtakytkentä. Kaikki liitännät on irrotettava, jotta jännite poistetaan laitteesta. Attention Cette unité peut avoir plus d'une connexion d'alimentation. Pour supprimer toute tension et tout courant électrique de l'unité, toutes les connexions...
Page 183 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Aviso Esta unidade pode ter mais de uma conexão de fonte de alimentação. Todas as conexões devem ser removidas para interromper a alimentação da unidade.
Page 184: Ground Conductor
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Ground Conductor This equipment must be grounded. Never defeat the ground conductor or Warning operate the equipment in the absence of a suitably installed ground conductor.
Page 185 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Warnung Dieses Gerät muss geerdet sein. Auf keinen Fall den Erdungsleiter unwirksam machen oder das Gerät ohne einen sachgerecht installierten Erdungsleiter verwenden. Wenn Sie sich nicht sicher sind, ob eine sachgerechte Erdung vorhanden ist, wenden Sie sich an die zuständige Inspektionsbehörde oder...
Page 186: Installing Or Replacing The Unit
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Installing or Replacing the Unit When installing or replacing the unit, the ground connection must always be Warning made first and disconnected last. Statement 1046...
Page 187 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Avvertenza In fase di installazione o sostituzione dell'unità, eseguire sempre per primo il collegamento a massa e disconnetterlo per ultimo. Advarsel Når enheten installeres eller byttes, må jordledningen alltid tilkobles først og frakobles sist.
Page 188: Use Copper Conductors Only
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Use Copper Conductors Only Warning Use copper conductors only. Statement 1025 Waarschuwing Gebruik alleen koperen geleiders. Varoitus Käytä vain kuparijohtimia. Cisco 11500 Series Content Services Switch Hardware Installation Guide...
Page 189 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Attention Utilisez uniquement des conducteurs en cuivre. Warnung Verwenden Sie ausschließlich Kupferleiter. Avvertenza Usate unicamente dei conduttori di rame. Advarsel Bruk bare kobberledninger.
Page 190: Short-Circuit Protection
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Short-circuit Protection Warning This product requires short-circuit (overcurrent) protection, to be provided as part of the building installation. Install only in accordance with national and local wiring regulations.
Page 191 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Advertencia Este producto necesita estar conectado a la protección frente a cortacircuitos (sobretensiones) que exista en el edificio. Instálelo únicamente en conformidad con las regulaciones sobre cableado, tanto locales como nacionales, a las que se tenga que atener.
Page 192 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Cisco 11500 Series Content Services Switch Hardware Installation Guide D-60 78-16421-01...
Page 193: Blank Faceplates And Cover Panels
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Blank Faceplates and Cover Panels Blank faceplates and cover panels serve three important functions: they Warning prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment;...
Page 194 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Attention Ne jamais faire fonctionner le système sans que l’intégralité des cartes, des plaques métalliques et des panneaux avant et arrière ne soient fixés à leur emplacement.
Page 195 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings ¡Advertencia! Las placas frontales y los paneles de relleno cumplen tres funciones importantes: evitan la exposición a niveles peligrosos de voltaje y corriente dentro del chasis;...
Page 196 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Aviso Plaquetas vazias e painéis de proteção têm três funções importantes: impedem a exposição a tensões e correntes elétricas perigosas dentro do chassi;...
Page 197 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Cisco 11500 Series Content Services Switch Hardware Installation Guide D-65 78-16421-01...
Page 198: Power Module
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Power Module Never install an AC power module and a DC power module in the same Warning chassis. Statement 1050 Waarschuwing Een voedingsmodule met wisselstroom mag nooit samen met een gelijkstroomvoedingsmodule in het chassis geïnstalleerd worden.
Page 199 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Aviso Nunca instale um modulo de corrente CA (corrente alternada) e um modulo CC (corrente contínua) no mesmo chassis. ¡Advertencia! Nunca instale un módulo de potencia de corriente alterna (CA) en un módulo de potencia de corriente continua (CC) en el mismo chasis.
Page 200: Ground Conductor
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Ground Conductor Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor.
Page 201 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Advarsel Dette utstyret må jordes. Omgå aldri jordingslederen og bruk aldri utstyret uten riktig montert jordingsleder. Ta kontakt med fagfolk innen elektrisk inspeksjon eller med en elektriker hvis du er usikker på...
Page 202 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Cisco 11500 Series Content Services Switch Hardware Installation Guide D-70 78-16421-01...
Page 203: I N D E X
Switch Control Module 2-11 console port application protocol audience connector pinouts troubleshooting 2-44 CSS 11501 installing 1-12 mounting bracket installation 1-13 cabling overview CSS 11501 unpacking CSS 11503 Cisco 11500 Series Content Services Switch Hardware Installation Guide IN-1 78-16421-01...
Page 204 2-35 Fast Ethernet Module (FEM) LEDs 2-48 16-port LEDs and connectors 2-16 troubleshooting 2-45, 2-46 8-port LEDs and connectors 2-15 disk LED definitions 2-17 failure 2-40, 2-43 pinouts specifications Cisco 11500 Series Content Services Switch Hardware Installation Guide IN-2 78-16421-01...
Page 205 CSS 11506 brackets 1-18 chassis ground connection 2-23 modem, connecting to a CSS CSS 11501 1-12 module CSS 11503 1-14 installation precautions 1-20 CSS 11506 1-17 installing 1-19, 1-24 Cisco 11500 Series Content Services Switch Hardware Installation Guide IN-3 78-16421-01...
Page 206 US electrical codes LEDs 2-47 safety warning 1-12, 1-14, D-1 troubleshooting 2-45, 2-46 screws, for grounding 2-24, 2-25 preinstallation requirements 1-11 protocols, supported A-6 to A-8 Cisco 11500 Series Content Services Switch Hardware Installation Guide IN-4 78-16421-01...
Page 207 LEDs 2-13 wiring LED definitions 2-5, 2-14 chassis ground 2-24 passive switchover 1-26 safety (warning) tools and equipment required tools and supplies, connecting chassis to ground 2-24 Cisco 11500 Series Content Services Switch Hardware Installation Guide IN-5 78-16421-01...
Page 208 Index Cisco 11500 Series Content Services Switch Hardware Installation Guide IN-6 78-16421-01...

This manual is also suitable for:

11500 series

Cisco CSS5 SSL K9 - Syst. CSS11500 SSL MODULE Hardware Installation Manual

Preface

Chapter 1 Unpacking and Installing the CSS

Figure 1-1 Front-Mounting the Mounting Brackets on the CSS 11501

Figure 1-2 Front-Mounting the Mounting Brackets on the CSS 11503

Figure 1-3 MID-Mounting the Mounting Brackets on the CSS 11503

Figure 1-4 Front-Mounting Position of the CSS 11506 Mounting Brackets

Figure 1-5 MID-Mounting the Mounting Brackets on the CSS 11506

Table 1-4 CSS 11506 Chassis Slot Restriction

Table 1-3 CSS 11503 Chassis Slot Restriction

Figure 1-6 Fully-Configured CSS 11503

Figure 1-7 Fully-Configured CSS 11506

Figure 1-8 Installing a Module into a CSS Chassis

Figure 1-9 Installing a PCMCIA Cover on an SCM

Chapter 2 Cabling and Troubleshooting the CSS

Figure 2-3 CSS 11506 Content Services Switch

Figure 2-4 Switch Control Module Connectors and Leds

Figure 2-5 8-Port Fast Ethernet Module Connectors and Leds

Figure 2-6 16-Port Fast Ethernet Module Connectors and Leds

Table 2-2 Switch Control Module LED Descriptions

Table 2-3 Fast Ethernet Module LED Descriptions

Figure 2-16 Location of the CSS 11506 Power Supplies

Figure 2-18 CSS 11506 DC Power Supply Leds

Figure 2-17 CSS 11506 AC Power Supply Leds

Table 2-14 Leds of the CSS 11506 Power Supply

Figure 2-8 Session Accelerator Module Leds

Appendix

Specifications

Appendix

Cable Connector Pinouts

Appendix

Connecting a Modem to the CSS

Appendix

Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch

I N D E X

Quick Links

Troubleshooting

Related Manuals for Cisco CSS5 SSL K9 - Syst. CSS11500 SSL MODULE

Summary of Contents for Cisco CSS5 SSL K9 - Syst. CSS11500 SSL MODULE