Honeywell #HZ-7000 - Sure-set Digital Heater Fan Owner's Manual

Hz-7000 series precision heat digital heater fan
Hide thumbs Also See for #HZ-7000 - Sure-set Digital Heater Fan:

Quick Links

IMPORTANT
SAFEGUARDS
READ AND SAVE THESE
SAFETY INSTRUCTIONS
BEFORE USING THIS
HEATER.
When using electrical appliances, basic precautions
should always be followed to reduce the risk of fire,
electric shock, and injury to persons, including the
following:
IMPORTANT
INSTRUCTIONS
1. Read all instructions before using this heater.
2. This heater is hot when in use. To avoid burns, do not
let bare skin touch hot surface. If provided, use han-
dles when moving this heater. Keep combustible
materials, such as furniture, pillows, bedding,
papers, clothes, and curtains at least 3 feet (0.9 m)
from the front of the heater and keep them away from
the sides and rear.
3. Extreme caution is necessary when any heater is
used by or near children or invalids and whenever
the heater is left operating and unattended.
4. Always unplug heater when not in use.
5. Do not operate any heater with a damaged cord or
plug or after the heater malfunctions, has been
dropped or damaged in any manner. Return heater
to authorized service facility for examination, electri-
cal or mechanical adjustment, or repair.
6. Do not use outdoors.
7. This heater is not intended for use in bathroom, laun-
dry areas and similar moist indoor locations. Never
locate heater where it may fall into a bathtub or other
water container.
8. Do not run cord under carpeting. Do not cover cord
with throw rugs, runners, or the like. Arrange cord
away from traffic areas where it will not be tripped
over.
PRECISION HEAT
DIGITAL HEATER FAN
HZ-7000, HZ-7010, HZ-7020, HZ-7030,
HZ-7040 Series
9. This appliance has a polarized plug (one blade is
wider than the other). To reduce the risk of shock,
this plug is intended to fit only one way in a polarized
outlet. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a quali-
fied electrician.
safety feature.
10. This heater draws 12.5 amps during operation. To
prevent overloading a circuit, do not plug the heater
into a circuit that already has other appliances work-
ing.
11. It is normal for the plug to feel warm to the touch;
however, a loose fit between the AC outlet (recepta-
cle) and plug may cause overheating and distortion
of the plug. Contact a qualified electrician to replace
loose or worn outlet.
12. To disconnect the heater, first turn controls to the
OFF
position, then grip the plug and pull it from the
wall outlet. Never pull by the cord.
13. Do not insert or allow foreign objects to enter any
ventilation or exhaust opening as this may cause an
electric shock or fire, or damage the heater.
14. To prevent a possible fire, do not block air intakes or
exhaust in any manner. Do not use on soft surfaces,
like a bed, where openings may become blocked.
15. A heater has hot and arcing or sparking parts inside.
Do not use it in the areas where gasoline, paint, or
flammable liquids are used or stored.
16. Use this heater only as described in this manual.
Any other use not recommended by the manufac-
turer may cause fire, electric shock, or injury to per-
sons.
17. Avoid the use of an extension cord because the
extension cord may overheat and cause a risk of fire.
However, if you have to use an extension cord, the
cord shall be No. 14 AWG minimum size and rated
not less than 1875 watts.
18. The output of this heater may vary and its tempera-
ture may become intense enough to burn exposed
skin. Use of this heater is not recommended for per-
sons with reduced sensitivity to heat or an inability to
react to avoid burns.
SAVE THESE
19.
INSTRUCTIONS.
1
DO NOT
attempt to defeat this
TM
loading

Summary of Contents for Honeywell #HZ-7000 - Sure-set Digital Heater Fan

  • Page 1: Important Safeguards

    PRECISION HEAT DIGITAL HEATER FAN HZ-7000, HZ-7010, HZ-7020, HZ-7030, HZ-7040 Series IMPORTANT 9. This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of shock, this plug is intended to fit only one way in a polarized SAFEGUARDS outlet.
  • Page 2 MODE: SET TIMER BASIC CONTROL PANEL OPERATION Timer POWER Power Continuous Run Mode Power Mode • Press Mode until the Timer icon blinks. The Hour display will appear • Use the Up or Down arrows to set an operation time between 1 and 10 hours.
  • Page 3: Remote Control Operation

    BACK-LIT DISPLAY (HZ-7000, HZ-7010 POWER: SERIES) Power Mode Back-Lit Power • The Back-lit feature provides light to the heater dis- play and functions in any power or mode setting. • Press the Back-lit button to toggle this feature on Basic Remote LCD Remote and off.
  • Page 4: Troubleshooting

    MODE: SET TIMER BACK-LIT DISPLAY (HZ-7000, HZ-7010 SERIES) Timer Mode MODE MODE Adjust Up or Down Back-lit LCD Remote Basic Remote • Press Mode until the Timer icon blinks on the Control Panel. The Hour display will also appear on the Con- LCD Remote Basic Remote trol Panel.
  • Page 5 WAX, POLISH, OR ANY CHEMICAL SOLU- the original date of purchase. TION. B. At its option, Honeywell will repair or replace • Clean your heater using the above-mentioned this product if it is found to be defective in steps, then pack the heater in its original con- material or workmanship.

This manual is also suitable for:

Hz-7021w - sure-set digital heaterPrecision heat hz-7000Precision heat hz-7010Precision heat hz-7020Precision heat hz-7030Precision heat hz-7040