1. Manuals
  2. Brands
  3. Sharp Manuals
  4. Fax Machine
  5. A260 - UX B/W Thermal Transfer
  6. Service manual

Sharp A260 - UX B/W Thermal Transfer Service Manual

Service manual
Hide thumbs
Table of Contents

Quick Links

Illustration: UX-A260U
Chapters 1, 2, 3, 7 and 8 of this manual are omitted because they are partly common to the UX-P100U.
Please refer to previous service manual (00ZUXP100USME) for these chapters.
[1] Specifications ............................................ 1-1
[2] Operation panel ......................................... 1-2
[4] Refer to the service manual of UX-P100U.
[5] Quick setup guide ..................................... 1-3
[6] Quick reference guide ............................... 1-4
(UX-5CR) ............................................1-4
[1] Adjustments ............................................... 2-1
[4] Refer to the service manual of UX-P100U.
[1] Refer to the service manual of UX-P100U.
[2] Refer to the service manual of UX-P100U.
[1] Block diagram ............................................4-1
[2] Wiring diagram .......................................... 4-2
[3] Point-to-point diagram ............................... 4-3
Parts marked with "
" are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for
maintaining the safety and performance of the set.
SERVICE MANUAL
CONTENTS
SHARP CORPORATION
No. 00ZUXA260USME
FACSIMILE
MODEL
MODEL
SELECTION CODE DESTINATION
UX-A260
[1] Circuit description ...................................... 5-1
power supply PWB ............................5-13
[5] Circuit description of CIS unit ...................5-13
[1] Control PWB circuit ................................... 6-1
[2] TEL/LIU PWB circuit ................................. 6-9
[3] Power supply PWB circuit ...................... 6-14
[4] Operation panel PWB circuit ................... 6-16
[2] Refer to the service manual of UX-P100U.
[1] Service tools .............................................. 8-1
[3] Refer to the service manual of UX-P100U.
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
UX-A260U
UX-A260
U
U.S.A.
Table of Contents
loading

Related Manuals for Sharp A260 - UX B/W Thermal Transfer

Summary of Contents for Sharp A260 - UX B/W Thermal Transfer

  • Page 1: Table Of Contents

    " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set. This document has been published to be used SHARP CORPORATION for after sales service only. The contents are subject to change without notice.
  • Page 2 UX-A260U CAUTION FOR BATTERY REPLACEMENT (Danish) ADVARSEL ! Lithiumbatteri-Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. (English) Caution ! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer.

  • Page 3: Chapter 1. General Description

    Copy Bond As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specifications figures indicated are nominal values of production units. There may be some deviations from these values in individual units.

  • Page 4: Operation Panel

    UX-A260U [2] Operation panel RESOLUTION/ SPEAKER TEL FAX RECEPTION MODE STOP FLASH REC/ MEMO PQRS WXYZ COPY/HELP/POLL PLAY/ HOLD SPEED START/MEMORY FUNCTION REDIAL REPEAT SKIP DELETE 10 11 17 18 1. SPEAKER key 9. Panel release Press this key to listen to the line and fax tones through the Press this release to open the operation panel.

  • Page 5: Refer To The Service Manual Of Ux-P100U

    UX-A260U [3] Transmittable documents [4] Installation Refer to the service manual of UX-P100U. Refer to the service manual of UX-P100U. Note: To enter your name and fax number and set the date and time so that they [5] Quick setup guide appear at the top of each fax you send, see pages 17 - 20 of your operation manual.

  • Page 6: Quick Reference Guide

    UX-A260U [6] Quick reference guide [7] Option imaging film specifications (UX-5CR) SENDING FAXES Place your document (up to 10 pages) face down in the document feeder. 1. Structure This article is composed of polyester film coated with heat-resistant layer, matt layer and hot melt ink layer, leader film and paper core. Ink film specification is "DNP standard ink film HC".

  • Page 7: Chapter 2. Adjustments

    UX-A260U CHAPTER 2. ADJUSTMENTS 3. Settings (1) Dial mode selector [1] Adjustments DIAL mode (Soft Switch No. SW-B4 DATA No. 3) (step 1) Select "OPTION SETTING". General KEY : FUNCTION Since the following adjustments and settings are provided for this model, DISPLAY: OPTION SETTING NUMBER OF RING...

  • Page 8: Diagnostics And Service Soft Switch

    UX-A260U [2] Diagnostics and service soft switch 1. Operating procedure (1) Entering the diagnostic mode Press FUNC 7 , and the following display will appear. ROM Ver. TB40 After 2 sec: DIAG MODE TB40 Then press the START key. Select the desired item with the key or the # key or select with the rapid key.

  • Page 9: Memory Clear

    UX-A260U 3. Diagnostic items description 3. 6. Signal send mode 3. 1. Soft switch mode This mode is used to send various signals to the circuit during FAX com- munication. Every push of START key sends a signal in the following Used to change the soft switch settings.
  • Page 10 UX-A260U 3. 12. Entry data receive 3. 13. Flash memory check In this mode, the registered data sent from the other machine is receiv- Data is written into and read from the flash memory to check data con- ed and the received data is registered in the machine. When this mode formity.
  • Page 11 UX-A260U 5. Soft switch description • Soft switch Switch setting and function Initial DATA ITEM Remarks setting Protect from echo Forced 4800 BPS reception Footer print Length limitation of copy/send/receive No limit Copy/send: 60cm Receive: 1m CSI transmission No transmitted Transmitted DIS receive acknowledgement during G3 Twice...
  • Page 12 UX-A260U Switch setting and function Initial DATA ITEM Remarks setting Reserved End Buzzer Disconnect the line when DIS is received in RX mode Equalizer freeze control (MODEM) Equalizer freeze control 7200 BPS only CNG transmission in manual TX mode Reserved Modem speed automatic fallback when RX level is under -40dBm Recall interval...
  • Page 13 UX-A260U Switch setting and function Initial DATA ITEM Remarks setting DTMF signal transmission level (High) Binary input No. = 16 8 4 2 1 1 2 3 4 5 0 0 1 0 1 Reserved Reserved Reading slice (Binary) Factory Light Dark Darker in...
  • Page 14 UX-A260U Switch setting and function Initial DATA ITEM Remarks setting Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved DTMF detection time 50ms 80ms 100ms 120ms No.
  • Page 15 UX-A260U Switch setting and function Initial DATA ITEM Remarks setting Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Busy tone detection ON/OFF time (Lower 150ms 200ms 250ms 350ms duration) No. 1 No. 2 Busy tone detection ON/OFF time (Upper 650ms 900ms...
  • Page 16 UX-A260U Switch setting and function Initial DATA ITEM Remarks setting A.M. quiet detect time Binary input No. = 16 8 4 2 1 1 2 3 4 5 0 0 1 1 0 CPC detection time 4ms 20ms 40ms 70ms 140ms 160ms 200ms 290ms No.6 No.7 No.8...
  • Page 17 UX-A260U Switch setting and function Initial DATA ITEM Remarks setting Reserved Reserved Sender’s phone number setting Cannot change Change allowed Reserved Reserved Summer time setting OPTION Ringer volume Middle High OPTION No. 7 No. 8 Reserved Reserved Reserved Handset receiver volume Middle High OPTION...
  • Page 18 UX-A260U Switch setting and function Initial DATA ITEM Remarks setting Paper set size LETTER LEGAL OPTION No. 1 No. 2 Automatic reduce of receive Auto 100 % OPTION Print contrast Normal Lighter Light Dark Darker OPTION No. 4 No. 5 No.
  • Page 19 UX-A260U Switch setting and function Initial DATA ITEM Remarks setting Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved...
  • Page 20 UX-A260U • Soft switch function description SW-A2 No. 8 CNG transmission When set to "0" , this model allows CNG transmission by pressing the SW-A1 No. 1 Protect from echo Start key in the key pad dialing mode. When set to "1", CNG transmis- sion in the key pad dialing mode cannot be performed.
  • Page 21 UX-A260U SW-A5 No. 5, No. 6 Digital cable equalizer setting SW-B2 No. 7, No. 8 Reserved (Reception for Caller ID) Set to "0". Line equalization when reception for CALLER ID is to be set according SW-B3 No. 1 ~ No. 5 Reserved to the line characteristics.
  • Page 22 UX-A260U SW-B6 No. 6 ~ No. 8 Reserved Set to "0". Phone Number Intended Ring Pattern Purpose SW-C1 No. 1, No. 2 Reading slice (Binary) Ring Pattern 555-1234 Voice Calls Standard Used to determine the set value of reading density in standard/fine mode. The standard setting is "00"...
  • Page 23 UX-A260U SW-D2 No. 4 Reserved SW-F1 No. 5 ~ No. 8 Remote operation code figure by external TEL (0 ~ 9) Set to "0". Remote operation codes can be changed from 0 through 9. If set to SW-D2 No. 5 Caller ID function greater than 9, it defaults to 9.
  • Page 24 UX-A260U SW-H1 No. 5 Busy tone detect continuation sound detect during SW-I3 No. 3 Two way record function If this switch is set to "1", the machine disables two way recording. Used to detect the continuous tone of specific frequency during OGM SW-I3 No.

  • Page 25: Refer To The Service Manual Of Ux-P100U

    UX-A260U SW-I7 No. 3, No. 4 AGC slew rate (Mic) SW-L1 No. 8 Reserved The AGC Slew Rate controls the convergence of the message playback Set to "0". level to the desired playback level. A large slew rate will allow faster SW-L2 No.

  • Page 26: Chapter 4. Diagrams [1] Block Diagram

    UX-A260U CHAPTER 4. DIAGRAMS [1] Block diagram 4 – 1 manuals4you.com manuals4you.com...

  • Page 27: Wiring Diagram

    UX-A260U [2] Wiring diagram 4 – 2...

  • Page 28: Point-To-Point Diagram

    UX-A260U [3] Point-to-point diagram CNMT TPBD- TPBD- CNLIUA CNLIUA TPAD- TPAD- RHS- RHS- TPBD TPBD TX/RX TPAD TPAD MOTOR +24VL +24VL MICMUTE MICMUTE TELIN TELIN TEL/LIU TELMUTE TELMUTE RXIN RXIN TXOUT TXOUT CNTH STRB1- STRB1- FILM FILM STRB2- STRB2- RANK RANK TELOUT TELOUT...

  • Page 29: Chapter 5. Circuit Description

    UX-A260U CHAPTER 5. CIRCUIT DESCRIPTION 3. Operational description Operational descriptions are given below: • [1] Circuit description Transmission operation When a document is loaded in stand-by mode, the state of the docu- ment sensor is sensed via the 1 chip fax engine (SCE214V). With 1.

  • Page 30: Circuit Description Of Control Pwb

    UX-A260U [2] Circuit description of control PWB 3) DMA Channels Six internal DMA channels support memory access for scanner, T.4/T.6, and resolution conversion. DMA Channel 2 can be reprogrammed for 1. General description external access to thermal printing, thermal transfer, or plain paper inkjet Fig.
  • Page 31 UX-A260U 12) Video Processing 20) Power Up/Down Control The CX06835 supports two modes of shading correction for scanner Power Up/Down detection is provided internally. The threshold voltages data non-uniformity arising from uneven sensor output or uneven illumi- are: nation. Corrections are provided on either an 8-pixel group or are ap- •...
  • Page 32 UX-A260U B) Modem block 4) Features • Group 3 facsimile transmission/reception 1) Facsimile Modem ITU-T V.17 and V.33 The modem can operate at 14400, 12000, 9600, 7200, 4800, 2400, or 300 bps, and can perform HDLC framing per T.30 at all rates. A pro- ITU-T V.29, V.27 ter, T.30, V.21 Channel 2, T.4 grammable DTMF detector, three programmable tone detectors, V.21 ITU-T V.17 and V.27 ter short train...
  • Page 33 UX-A260U Integrated Analog Control Resisters for 20438 The 20438 IA can be used as a Primary Integrated Analog (PIA) codec or as a Secondary Integrated Analog (SIA) codec, depending on the signal connection with the SCE Controller ASIC device. In the SCE100 product, both the PIA and the SIA are packaged external to the SCE Controller device, whereas in the SCE214V, the PIA is packaged with the SCE214V Controller and the SIA is external.
  • Page 34 UX-A260U SCE214V (IC3) Terminal descriptions Input Output Pin List Pin Description Type Type VDDPLL — — — PLL Power VSSPLL — — — PLL GND ROMCSn — 13Xs — SYNC/GPO[20] — 13Xs — — 13Xs — — 13Xs — DEBUGn —...
  • Page 35 UX-A260U SCE214V (IC3) Terminal descriptions Input Output Pin List Pin Description Type Type — — — Digital Power GPIO[11]/BE/SERINP/SR4IN 13Xs — GPIO[19]/RDY/SEROUT 13Xs — START — — CLK1n/GPO[25] — 13Xs — CLK2/GPO[24] — 13Xs — — — — IA GND MCLK —...
  • Page 36 UX-A260U SCE214V (IC3) Terminal descriptions Input Output Pin List Pin Description Type Type A[12] 13Xs CPU Address Bus A[13] 13Xs CPU Address Bus A[14] 13Xs CPU Address Bus A[15] 13Xs CPU Address Bus A[16] 13Xs CPU Address Bus — — —...
  • Page 37 UX-A260U (3) Panel control block The following controls are performed by the SCE214V. • Operation panel key scanning • Operation panel LCD display (4) Mechanism/recording control block • Recording control block diagram (1) TEST[1:0] BATRSTN RESETN TONE ALTTONE TSTCLK REGDMA WAITN OPO[7:0]* SYNC...

  • Page 38: Circuit Description Of Tel/Liu Pwb

    UX-A260U [3] Circuit description of TEL/LIU PWB (1) TEL/LIU block operational description 1) Block diagram TEL/LIU PWB CONTROL PWB RTLOOP MODEM BLOCK (20438 I/A) 0,6dB IC101-A SIGTX SPKRP LINE TXOUT MIC ENABLE SP OUT ENABLE CI DETECTOR SIGRX MICP RXIN /LINE PC2A SELECT...
  • Page 39 UX-A260U 5. CI detection circuit • CI is detected by the photo coupler which is integrated in series in the primary side TEL circuit well proven in the existing unit. 6. Signal/DTMF transmission level & receiving level • Signal transmission level setting: ATT -8 dB Circuit output: -11 dBm. •...
  • Page 40 UX-A260U [Signals for status recognition according to input signals] Signal Name Function Signal Name (CNLIUA) Signal Name (CNLIUA) H:The handset is in the on-hook state. RHS- TXOUT L: The handset is in the off-hook state. +24VL Incoming call (CI) detection signal MICMUTE FILM TELIN...

  • Page 41: Circuit Description Of Power Supply Pwb

    UX-A260U [4] Circuit description of power supply PWB 1. Block diagram 3.15A/125V Noise Rectifying +24V Filter AC IN Smoothing FUSE Switching Circuit Circuit 4A/32V Circuit Control Circuit Photo Coupler Fig. 7 2-1. Noise filter circuit 2-4. Control circuit The input noise filter section is composed of L1 and C1, which reduces This circuit controls output voltage of +24V by adjusting ON period of normal mode noise from the AC line and common mode noise to the AC Q1, looking at signal from photo coupler PC1.

  • Page 42: Chapter 6. Circuit Schematics And Parts Layout

    UX-A260U CHAPTER 6. CIRCUIT SCHEMATICS AND PARTS LAYOUT 6 – 1 manuals4you.com manuals4you.com...
  • Page 43 UX-A260U 6 – 2...
  • Page 44 UX-A260U 6 – 3 manuals4you.com manuals4you.com...
  • Page 45 UX-A260U 6 – 4...
  • Page 46 UX-A260U 6 – 5 manuals4you.com manuals4you.com...
  • Page 47 UX-A260U 6 – 6...
  • Page 48 UX-A260U Control PWB parts layout (Top side) 6 – 7 manuals4you.com manuals4you.com...
  • Page 49 UX-A260U Control PWB parts layout (Bottom side) 6 – 8...
  • Page 50 UX-A260U 6 – 9 manuals4you.com manuals4you.com...
  • Page 51 UX-A260U 6 – 10...
  • Page 52 UX-A260U 6 – 11 manuals4you.com manuals4you.com...
  • Page 53 UX-A260U TEL/LIU PWB parts layout (Top side) 6 – 12...
  • Page 54 UX-A260U TEL/LIU PWB parts layout (Bottom side) 6 – 13 manuals4you.com manuals4you.com...
  • Page 55 UX-A260U 6 – 14...
  • Page 56 UX-A260U Power supply PWB parts layout (Top side) Power supply PWB parts layout (Bottom side) 6 – 15 manuals4you.com manuals4you.com...
  • Page 57 UX-A260U 6 – 16...
  • Page 58 UX-A260U Operation panel PWB parts layout Operation panel PWB parts layout (Top side) (Bottom side) Note: Since the parts of PWB cannot be supplied, change it as a unit. 6 – 17 manuals4you.com manuals4you.com...

  • Page 59: Chapter 7. Operation Flowchart

    UX-A260U CHAPTER 7. OPERATION FLOWCHART [1] Protocol Refer to the service manual of UX-P100U. [2] Power on sequence Refer to the service manual of UX-P100U. 6 – 18...

  • Page 60: Chapter 8. Others [1] Service Tools

    UX-A260U CHAPTER 8. OTHERS [1] Service tools 1. List PRICE PARTS CODE DESCRIPTION Q’TY RANK CPWBF3201SCS1 Extension board unit (TEL/LIU PWB) PSHEZ3579SCZZ Shading wave memory standard paper Extension board unit TEL/LIU PWB (BROWN) (ORANGE) FILM (RED) +24VL (YELLOW) PRICE PARTS CODE DESCRIPTION Q’TY RANK...

  • Page 61: Parts Guide

    UX-A260U PARTS GUIDE UX-A260 MODEL MODEL SELECTION CODE DESTINATION UX-A260 U.S.A. CONTENTS Cabinet, etc. Control PWB unit Top cover/Sub frame TEL/LIU PWB unit Upper cabinet/Document guide upper Power supply PWB unit Drive unit Operation panel PWB unit Packing material & Accessories Index Because parts marked with "...

  • Page 62: Cabinet,Etc

    UX-A260U [1] Cabinet,etc. OPERATION PANEL UNIT DOCUMENT GUIDE UPPER TOP COVER/ SUB FRAME DRIVE UNIT – 1 – manuals4you.com manuals4you.com...
  • Page 63 UX-A260U PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [1] Cabinet,etc. CCNWN395BXH01 Speaker ass’y CLEVP2358XH01 Hook switch lever ass’y CROLR2481XH01 PO roller ass’y DCEKC481SXHZZ Control PWB unit(Within ROM) DCEKL498CXH01 TEL/LIU PWB unit QPWBF3368XHZ2 Wire holder(PWB only) QCNWN425BXHZZ Panel cable LBNDJ2006XHZZ Band(100mm) LBSHP2140XHZA Back bearing,left...
  • Page 64 UX-A260U [2] Top cover/Sub frame PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [2] Top cover/Sub frame GCOVA2448XHVA Top cover MSPRC3301XHZZ Hopper spring NGERP2318XHZZ Pinion gear PGIDM2619XHVA Hopper guide,left PGIDM2620XHVA Hopper guide,right LFRM-2227XHZZ Sub frame LFRM-2232XHZZ Sub frame plate MLEVP2363XHZZ P-IN sensor lever,upper MSPRC3305XHZZ Release lever spring...
  • Page 65 UX-A260U [3] Upper cabinet/Document guide upper PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [3] Upper cabinet/Document guide upper GCASP2173XHSB Panel case JBTN-2357XHSB 12 key JBTN-2359XHSF Start key JBTN-2358XHSB Function key DCEKP478CXH02 Operation panel PWB unit QSW-Q2331XHZZ Tact switch [SW] QSW-M2246AXZZ FRSNS sensor QSW-M2294XHZZ...
  • Page 66 UX-A260U [4] Drive unit 10 2 PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [4] Drive unit CGERH2314XH05 Slip gear ass’y CLEVP2359XH01 Planet gear lever ass’y A CLEVP2360XH01 Planet gear lever ass’y B CLEVP2361XH01 Planet gear lever ass’y C CLEVP2362XH01 Planet gear lever ass’y D LFRM-2226XHZZ Drive unit frame...

  • Page 67: Packing Material & Accessories

    UX-A260U [5] Packing material & Accessories TAPE TAPE TAPE TAPE 11 8 AC CORD PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [5] Packing material & Accessories DUNTK497CXHFW Handset QCNWG209BXHOW Handset cord CPLTP3222XHR2 Paper tray extension NGERH2568XHZZ Imaging film gear PRBNN2038SC10 Imaging film(Initial starter film 10m) QCNWG208BXHZZ...

  • Page 68: Control Pwb Unit

    UX-A260U PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [6] Control PWB unit UBATL2049SCZZ Battery(CR2032T23) [BAT1] VCEAGA0JW227M Capacitor(6.3WV 220 F) [C1] VCEAGA1EW476M Capacitor(25WV 47 F) [C2] VCEAGA1HW106M Capacitor(50WV 10 F) [C3] VCEAGA1HW106M Capacitor(50WV 10 F) [C4] VCEAGA1HW106M Capacitor(50WV 10 F) [C6] VCEAGA1HW106M Capacitor(50WV 10 F)
  • Page 69 UX-A260U PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [6] Control PWB unit VCKYCY1AB105K Capacitor(10WV 1.0 F) [C208] VCKYCY1HB471K Capacitor(50WV 470PF) [C211] VCKYCY1HF104Z Capacitor(50WV 0.1 F) [C212] VCKYCY1HF104Z Capacitor(50WV 0.1 F) [C218] QCNCM2666XH0G Connector(7pin) [CNCIS] QCNCM7014SC0B Connector(2pin) [CNCSW] QCNCM2508SC1D Connector(14pin) [CNLIUA] QCNCM7014SC0F Connector(6pin)

  • Page 70: Tel/Liu Pwb Unit

    UX-A260U PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [6] Control PWB unit VRS-CY1JB103J Resistor(1/16W 10K [R151] VRS-CY1JB203J Resistor(1/16W 20K [R152] VRS-CY1JB102J Resistor(1/16W 1K [R153] VRS-CY1JB222J Resistor(1/16W 2.2K [R154] VRS-CY1JB000J Resistor(1/16W 0 [R155] VRS-CY1JB103J Resistor(1/16W 10K [R156] VRS-CY1JB106J Resistor(1/16W 10M [R157] VCKYCY1HF104Z Capacitor(50WV 0.1 F)

  • Page 71: Power Supply Pwb Unit

    UX-A26U PRICE PRICE PART PART DESCRIPTION DESCRIPTION PARTS CODE PARTS CODE RANK RANK MARK MARK RANK RANK [7] TEL/LIU PWB unit VHD1N4148//-1 Diode(1N4148) [D2] VHD1N4148//-1 Diode(1N4148) [D3] VHD1N4148//-1 Diode(1N4148) [D100] VHD1N4148//-1 Diode(1N4148) [D101] VHINJM2902M-1 IC(NJM2902M) [IC101] RFILN2035XHZZ Coil(LSHSR02C-001) [L4] RFILN2035XHZZ Coil(LSHSR02C-001) [L8] VHPPC814X//-1...

  • Page 72: Operation Panel Pwb Unit

    UX-A260U PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [8] Power supply PWB unit 0CBUBA0003BL/ Diode(1S2076A) [D5] 0CBUBC0336AZ/ Diode(S3L20U) [D7] 0CBUBC0070AM/ Diode(ERA81-004V3) [D8] 0CBUBC0169CL/ Diode(ERA22-06V3) [D9] 0CBPJCEJ3151/ Fuse(3.15A/AC125V) [F1] 0CBPZZ1008ZZ/ Circuit protector(4A/32V) [F3] 0CBBFZ89902Z/ Beads core(3A) [FB2] 0CBBFZ89633Z/ Beads inductor(BP53RB052025050) [FB3] 0CBUKZ1186ZZ/ Filter(33mH/0.5A)
  • Page 73 UX-A260U I n d e x PRICE PART PRICE PART PRICE PART PARTS CODE PARTS CODE PARTS CODE MARK MARK MARK RANK RANK RANK RANK RANK RANK MSPRC3346XHZZ 1-66 QSW-M2294XHZZ CCNWN395BXH01 MSPRC3357XHZZ 1-67 CGERH2314XH05 MSPRD3285XHZZ 1-53 QSW-Q2331XHZZ CGERH2566XH01 5-21 MSPRD3286XHZA 1-52 CLEVP2358XH01 MSPRD3291XHZZ...
  • Page 74 UX-A260U PRICE PART PRICE PART PRICE PART PARTS CODE PARTS CODE PARTS CODE MARK MARK MARK RANK RANK RANK RANK RANK RANK VCEAGA1HW226M VHEHZ2A1///-1 7-90 VRS-CY1JB203J 6-170 VCEAGA1HW475M 7-10 VHEHZ2C1///-1 7-87 VRS-CY1JB204J 6-153 VCKYCY1AB105K 6-64 7-88 VRS-CY1JB222J 6-163 6-66 VHEHZ27-1//-1 7-86 VRS-CY1JB223J 6-174...
  • Page 75 UX-A260U PRICE PART PRICE PART PRICE PART PARTS CODE PARTS CODE PARTS CODE MARK MARK MARK RANK RANK RANK RANK RANK RANK 0CBUAC0034EL/ 8-36 0CBUAC0255AM/ 8-34 0CBUAC0264AK/ 8-35 0CBUAG0213AC/ 8-33 0CBUBA0003BL/ 8-21 0CBUBC0070AM/ 8-23 0CBUBC0169CL/ 8-24 0CBUBC0336AZ/ 8-22 0CBUBDBE100C/ 8-66 0CBUBDBE4R3C/ 8-63 0CBUBDBE6R2C/...
  • Page 76 UX-A260U © COPYRIGHT 2003 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.

This manual is also suitable for:

Ux-a260

Table of Contents