Note
Tip
Do not connect a VCR, etc., between your TV and the player. If you pass
Run the cables into the hole marked with an “
” in the illustration
*
the player signals via the VCR, you may not receive a clear image on the
above, so that you can bundle and fix the cables.
TV screen. If your TV has only one video input jack, connect the Unit to
Notes
this jack.
• Make sure that the pre-construction bracket is properly level, both
horizontally and vertically. Improper positioning may cause the
unit to fall, or may cause difficulty when you install the Unit.
• Make sure that more than 4 inches (10 cm) of space is available
behind the wall for installing the unit.
3
Place the AM loop antenna on the stud, and then fasten
the supplied screws to attach it. Raise the entire AM
Connecting audio Equipment
antenna, and then insert its tab into the notch to set up
the AM loop antenna.
Connections between the Unit and each of devices are made via
Take care to attach the AM loop antenna on the stud as far
cables or cords coming through the wall.
away from the CDP-NW10, DVP-NW50, or other electrical
The Unit can input sound from external audio equipment via the
devices as possible (at least 1 foot (30 cm)).
audio connectors on the Unit. Connect the OUTPUT jacks (L/R)
of the audio equipment to the LINE IN (L/R) jacks of the Unit
using the proper audio cords (optional).
Connecting an IR IN/OUT
Connections between the Unit and each of devices are made via
cables or cords coming through the wall.
4
After the wall construction is finished, cut the outline
You can operate a component using the remote if the IR IN/OUT
along the inside edge of the pre-construction bracket.
terminal of the Unit and the component are connected. For
Do not cut over or beyond the edge.
example, if you connect IR IN of the Unit and IR OUT of a TV,
Before proceeding to step 4, make sure that all the necessary
you can operate the Unit with the remote by aiming it at the TV.
cables can be run to the bracket location.
Note
Make sure that the size of the hole cut in the wall corresponds to the
3
7
specified size (height: 8
/
X 8
/
inches, 212.5 - 215 mm), (width:
8
16
3
1
8
/
X 8
/
inches, 207.5 - 210 mm). If the hole is too big to mount
16
4
the bracket, the Unit may fall and cause an accident.
5
Place the mounting bracket over the hole so that the pre-
construction bracket and the mounting bracket match
across the wall. Then fasten the wall mounting bracket
screws carefully to fix the mounting bracket and pre-
construction bracket so that they are level and align
If you connect IR OUT of the Unit and IR IN of a component,
perfectly.
such as a DVD Changer, you can operate the DVD Changer with
Make sure the larger tab is mounted at the bottom.
the remote (supplied with the DVD Changer) by aiming it at the
Unit.
Connecting an AC power unit
Larger tab
After connecting the Unit and the AC power unit using the
Notes
power supply cables, connect the AC power cord to the AC IN of
• Fasten the screws securely. Failure to fasten the screws or
the AC power unit, then the other end of the AC power cord to
incomplete tightening of the screws may cause the Unit to fall and
the wall outlet.
cause an accident.
• For mounting the bracket, use the supplied screws.
Installing the Unit
To mount the unit on the finished wall
1
Mark the location where the Unit is to be installed on the
Before installing the Unit into the wall, take steps to ensure your
wall using the supplied TEMPLATE (8
3
/
X 8
1
/
inches (212.5
8
4
safety and that of your surroundings, then check the following:
mm X 207.5 mm)).
• The location of the power source to make sure that power supply cable
Make sure the mark is properly level, horizontally and
can reach from the Unit.
vertically.
• The location of the speakers to make sure that speaker cords can be run
2
between the Unit and the speakers.
Cut the outline along the mark, then carefully cut a clean
• The distance between the Unit and the AC power unit (up to 200 feet
hole through the wall.
(60 m)).
Notes
• The durability of the wall (The thickness of the wall must be between
• Do not cut over or beyond the outline.
1/2 to 3/4 inches. (13 mm to 19 mm)).
• Make sure that the size if the hole cut in the wall corresponds to the
• There are no obstructions, such as an air, an electrical, or a water
specified size. If the hole is too big to mount the bracket, the Unit
conduit near the location where the Unit is installed.
may fall and cause an accident.
• There is enough space (over 6 inches (15 cm)) inside the wall. If the
• Do not make a gap between the wall and the mounting bracket.
space available inside the wall is insufficient or does not have proper
ventilation, a malfunction of the Unit may occur due to heat build-up.
3
Rotate the stoppers to the inside of the frame, and then
• Do not install the Unit where the Unit may get wet due to water or
place the mounting bracket over the hole.
other liquid. This may cause a malfunction of the Unit.
Make sure the larger tab is mounted at the bottom.
• Do not install the Unit in a place where moisture condensation may
4
cause a malfunction of the Unit.
Rotate the stoppers to the outside of the frame behind
the wall.
Installing brackets for new construction (before
wall construction is finished)
You may install a pre-construction bracket on the studs where the
unit will be installed. It is recommended that you use a pre-
construction bracket when you install the unit in a house that is
still under construction. However, the pre-construction bracket is
only for the use of sub installation. You may not be able to use the
pre-construction bracket on the place where the wall and material
of the wall and pillar may be damaged or some other problems
may occur.
Note
The following items are included in the Pre-construction bracket kit (WS-
BKT1).
• Pre-construction bracket (1)
Larger tab
• Wings (2)
• AM Antenna (1)
5
Fasten the wall mounting bracket screws carefully so that
• Screws for the AM Antenna (2)
the wall mounting bracket is level.
• Manual (1)
1
Insert the two wings into the tabs of the pre-construction
bracket.
Wing
2
Place the pre-construction bracket on the studs, and then
fasten the screws (not supplied) to attach the pre-
construction bracket.
Notes
• Fasten the screws securely. Failure to fasten the screws or
incomplete tightening of the screws may cause the Unit to fall and
cause an accident.
• For mounting the bracket, use the supplied screws.
*