Craftsman 113.29931 Owner's Manual

Rail and fence system for craftsman 10" table saws: 113.299310; 113.299510; 113.299410; 315.228310; 315.228410; 315.228510;
Owner's Manual
II:RRFTSMRN'I
RAILS AND FENCE SYSTEM
FOR CRAFTSMAN
10 in. TABLE SAWS MODEL NOS.
315.228310,
315.228410,
315.228510,
113.299310,
113.299410,
113.299510
Item No.
_929993
TABLE SAWNOT INCLUDED
Save this manual
for
future
reference.
_,
CAUTION:
Read and follow
all Safety
Rules and Operating
Instructions
before first use of
this product.
Customer
Help Line: 1-800-932-3188
Sears,
Roebuck
and Co.,
Hoffman
Estates,
IL 60179
USA
Visit the Craftsman
web page: www.sears.com/craftsman
972000-662
3-99
SAFETY
LOOSE
PARTS
PREPARATION
INSTALLATION
ALIGNMENT
Table of Contents
loading

Summary of Contents for Craftsman 113.29931

  • Page 1 Rules and Operating Instructions before first use of this product. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., Hoffman Visit the Craftsman web page: www.sears.com/craftsman 972000-662 3-99 10 in. TABLE SAWS MODEL NOS. 315.228510, 113.299310, Estates, IL 60179 113.299410, 113.299510 TABLE SAWNOT INCLUDED •...
  • Page 2 FOR YOUR TABLE SAW THOROUGHLY before using accessories. KNOW YOUR POWER TOOL. Read the owner's manual for the Table Saw carefully. Learn the saw's applications and limitations as well as the specific potential hazards related to this tool. KEEP THE WORK AREA CLEAN. Cluttered work areas and work benches invite accidents.
  • Page 3 REMOVING THE SWITCH AND RAILS • Remove the front rail end caps. • Under the front rail, loosen the switch screws and slide the switch off of the rail. See Figure 2. Note: Do not remove the switch screws completely. Loosening the screws will allow you to slide the switch off the front rail and the switch will be...
  • Page 4 Position rail so that the right hand edge extends 2-1/2 in. beyond the table extension. Note: Instructions are given from the operator's position in front of the saw. • Push the rail against table and tighten each hex nut with a 12 mm wrench. If the rail jams or does...
  • Page 5 (Bottom slot is for switch.) • Align the rail left to right - Match the 7-1/8 in. mark on the right scale to the right edge of the saw base (main table). See Figure 8. • Snug the rail against table. Finger-tighten on the table and extensions.
  • Page 6 Locate the switch assembly, The fasteners should still be attached. Note: If the fasteners were removed from the switch, see instructions in your table saw Owner's Manual for mounting the switch or refer to Figure 10. • Holding the switch to the front, insert and slide the two square nuts into the lower slot of the front rail.
  • Page 7 ALIGNING THE RIP FENCE AND FRONT The rip fence scale indicator is installed on the right side of the rip fence but can be removed and rein- stalled on the left side if needed. If a cutting operation requires placing the rip fence on the left side of the blade, and you find relocating the indicator necessary, simply unscrew and re-attach it.
  • Page 8 CHECKING RIP FENCE AND. BLADE ALIGNMENT The rip fence is self-aligning but should be checked before first use. WARNING: Failure to align the rip fence to the blade can cause jams and kickback, resulting in serious personal injury. • Slide the rip fence to the miter gauge groove, which is parallel to blade.

This manual is also suitable for:

113.29951113.29941315.22831315.22841315.2285129993 ... Show all

Table of Contents