KitchenAid KRFF507HPS French Door Bottom Mount Quick Start Guide

KitchenAid KRFF507HPS French Door Bottom Mount Quick Start Guide

Also See for KRFF507HPS:
KitchenAid KRFF507HPS French Door Bottom Mount Quick Start Guide

OPERATING INSTRUCTIONS


Before operating this appliance, make sure it has been properly installed according to the appliance's Owner's Manual.

The control center is located at the top front of the refrigerator compartment.

NOTE: The display screen on the dispenser control panel will turn off automatically and enter "sleep" mode when the control buttons and dispenser paddles have not been used for 2 minutes or more. Press any control button to reactivate the display screen. The home screen will appear as shown.

Home screen

For your convenience, the temperature controls are preset at the factory. When you first install your refrigerator, make sure the controls are still set to the recommended setting as shown.

When you first install your refrigerator, make sure that the controls are still set to the recommended set points. The factory recommended set points are 37°F (3°C) for the refrigerator and 0°F (-18°C) for the freezer.

  • The recommended settings should be correct for normal household refrigerator use. The controls are set correctly when milk or juice is as cold as you like and when ice cream is firm.
    NOTE: Areas such as a garage, basement, or porch may have higher humidity or extreme temperatures. You may need to adjust the temperature away from the recommended settings to accommodate for these conditions.
  • Wait 24 hours for your refrigerator to cool completely before adding food. If you add food before the refrigerator has cooled completely, your food may spoil.
    NOTE: Adjusting the refrigerator and freezer controls to a colder than recommended setting will not cool the compartments any faster.

TEMPERATURE SET POINTS

  1. Press and hold Temp for 3 seconds to activate Temperature mode.
    NOTE: To view temperature in degrees Celsius, press the Light button, under Units, when adjust mode is activated. To return the display setting to Fahrenheit, press the Light button again.
    When Temperature mode is activated, press Temp to toggle between Fridge and Freezer. The display will show the temperature set point of the selected compartment and temperature adjusting information will appear on the display screen.
    Recommended Refrigerator Temperature

    Fridge set point range: 33°F to 42°F (0°C to 5.5°C)
    Recommended Freezer Temperature

    Freezer set point range: -5°F to 5°F (-21°C to -15°C)

When adjusting temperature set points, use the following chart as a guide.

CONDITION: TEMPERATURE ADJUSTMENT:
Refrigerator too cold Refrigerator setting 1° higher
Refrigerator too warm Refrigerator setting 1° lower
Freezer too cold Freezer setting 1° higher
Freezer too warm / too little ice Freezer setting 1° lower

Save/Confirm Temperature Settings
When you have finished adjusting both the refrigerator and freezer set points, press Measured Fill to confirm and to save the settings.

NOTE: To exit Temperature mode without saving changes, press the Ice/Water button under Back at any time, or allow about 60 seconds of inactivity. The temperature mode will turn off automatically and return to the normal screen.

COOLING ON/OFF

Your refrigerator and freezer will not cool when cooling is turned off.

To turn cooling off, press and hold the Lock and Measured Fill buttons at the same time for 3 seconds. The Cooling Off icon will blink seven times and then remain lit.

OPTIONS


All options are Off by default until selected.

  • Press the Options button to open the Options menu and select among the Max Ice, Filter Status and Max Cool features.
    NOTE: "Max Cool" and "Max Ice" illuminate to indicate when both features are On.

MAX COOL

The Max Cool feature assists with periods of high refrigerator use, full grocery loads, or temporarily warm room temperatures. Once selected, the Max Cool feature will remain on for 24 hours unless manually turned off.

  • To turn on the Max Cool feature, press the Options button to access the Options menu, then press Lock, under Max Cool to activate the feature. When the feature is on, the Max Cool icon will appear on the dispenser display screen.

NOTE: If you adjust the refrigerator temperature set point, Max Cool will turn off.

MAX ICE

The Max Ice feature assists with temporary periods of heavy ice use by increasing ice production. Once selected, Max Ice will remain on for 24 hours unless manually turned off.

  • To turn on the Max Ice feature, press the Options button to access the Options menu, and then press Temperature, under Max Ice to activate the feature. When the feature is On, the Max Ice icon will appear on the dispenser display screen.

VACATION MODE

In Vacation Mode, the freezer will defrost less often to conserve energy.

NOTES:

WATER FILTER STATUS

Press Options on the control panel to launch the Options menu. Press Options, under Filter Status, again to display the percentage of filter life remaining (from 99% to 0%). Press Ice/Water, under Back, to return to the Normal screen.

The water filter status lights will help you know when to change your water filter.

  • Yellow: ORDER FILTER — it is almost time to change the water filter. While you are dispensing water, "Order Filter" will blink seven times and sound an alert tone three times.
  • Red: REPLACE FILTER — Replace the water filter. While you are dispensing water, "Replace Filter" will blink seven times and an alert tone will sound three times.
    NOTE: "Replace Filter" will remain illuminated if a filter is not installed or is installed incorrectly.

Reset the water filter status tracking feature. After you replace the disposable filter with a new filter, closing the filter compartment door will automatically reset the filter status tracking feature.

DISPENSER LIGHT

When you use the dispenser, the lights will turn on automatically.


To turn on the light when you are not dispensing, press Light to toggle through the following choices in a continuous loop:

OFF (default): The dispenser light is Off.
ON: The dispenser light remains on at 100% brightness.
DIM: The dispenser light remains on at 50% brightness.

The dispenser lights are LEDs that cannot be changed. If it appears that your dispenser lights are not working, see online "Troubleshooting" for more information.

DISPENSER LOCK

The dispenser can be turned off for easy cleaning or to avoid unintentional dispensing by small children and pets.

NOTE: The lock feature does not shut off power to the refrigerator, to the ice maker, or to the dispenser light. It simply deactivates the controls and dispenser lever. To turn off the ice maker, see the "Ice Maker and Storage Bin" section in the Owner's Manual.

The display screen indicates when the dispenser is locked.

Online Ordering Information

For detailed installation instruction and maintenance information, winter storage, and transportation tips, please see the Owner's Manual included with your appliance.

For information on any of the following items, the full cycle guide, detailed product dimensions, or for complete instructions for use and installation, please visit https://www.kitchenaid.com/service-and-support, or in Canada https://www.kitchenaid.ca/service-and-support. This may save you the cost of a service call. However, if you need to contact us, use the information listed below for the appropriate region.

United States:
1–800–253–1301

KtichenAid Brand Home Appliances Customer eXperience Center
553 Benson Road, Benton Harbor, MI 49022–2692

Canada:
1–800–807–6777

KitchenAid Brand Home Appliances Customer eXperience Centre
200–6750 Century Ave., Mississauga, Ontario L5N 0B7

SAVE THESE INSTRUCTIONS

Documents / Resources

References

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Table of Contents