Quick Links
Smart Modular Revolving Door Installation Guide (21501043-003, 21501044-001)
01
安装门下安装件
Installing a Mounting Kit Under a Door
600mm宽机柜下封板
Bottom sealing plate for a 600 mm
wide cabinet
1
3
1
800mm宽机柜下封板
Bottom sealing plate for a 800 mm
wide cabinet
3
NOTE
Before installation, ensure that the left and right end cabinets are on
安装前确保左右列头机柜在同一水平线上，
the same horizontal line and ensure that the side of the skylight
确保天窗支撑板侧面与机柜侧面在同一平面上。
support plate and the sides of the cabinets are on the same plane.
步骤1：组装机柜等宽的前后封板。
Step 1: Assemble front and rear sealing plates that are as wide as the cabinet.
NOTE
根据实际情况卡接600mm宽或者800mm宽机
Connect the bottom sealing plate for the 600 mm or 800 mm wide
柜下封板。
cabinet based on the site requirements.
Step 2: Secure the front and rear sealing plates to the cabinet.
步骤2：将前、后封板固定在机柜上。
Step 3: Place the side sealing plate with dents upwards, and snap the side
步骤3：使侧封板带凹口侧朝上，将侧封板卡入
sealin plate into the front and rear sealing plates.
前、后封板中。
04
调节门缝
Adjusting the gap between the door panels
b
a
a
当门框倾斜角度较大时，调节机柜滚轮或地脚螺栓，
当门掉角时，可推动门立柱下端调整，当出现门板翘角，
若此时地面与立柱间有缝隙可用垫片补齐。
可拉动门立柱下端调整。
b
b
当微调时，直接使用垫片将低的立柱垫高。
当门错位时，可调松立柱与机柜间紧固螺钉，插入垫片使
a
If the door frame tilts by a large degree, adjust the
门板合时处于同一水平面，调整完成后将螺钉紧固复位。
a
castors or anchor bolts of the cabinet. If a post is lifted
If there is a gap between the door panel and upper frame
off the floor due to the adjustment, add a spacer under
mounting kit (a corner tilts downwards), you can push up
the post.
the lower end of the post. If a corner of a door panel tilts
b
If the door frame slightly tilts, add a spacer under the
upwards, pull the lower end of the post.
appropriate post to correct the tilt.
If door panels mismatch, loosen screws between the posts
b
and cabinets and insert spacers to make the door panels
on the same horizontal plane when they are closed. After
adjustment, tighten all screws.
如果上述方法仍无法完成门板调节，可拆下一边门板胶条并重新调节安装，直至两边门板边缘贴合。
NOTE
If the door gap is still uneven after the preceding measures are taken, remove, reinstall, and adjust the rubber strip
on one door panel until the door panel edges are in close contact.
智能微模块 旋转门 安装指南(21501043-003, 21501044-001)
02
安装门框
Installing a Door Frame
M5x10
列头柜
End cabinet
3 N·m
2
M6x16
3 N·m
05
b
1
a
1
2
M4
(21501044-001)
M6x16
1
3 N·m
A:有滚轮机柜固定孔位
B:无滚轮机柜固定孔位
(21501043-003)
A: Securing holes for cabinets with castors
B: Securing holes for cabinets without castors
NOTE
安装前，先拆除门楣背板、立柱侧面维护板。
Before installation, remove the door head rear panel.After the
将立柱和门楣平放在地面组装。组装完成后，确保
installation is complete, reinstall the rear panel.
Put the posts and door head horizontally on the floor and assemble
立柱与门楣各面对齐。
them. After the assembly is complete, verify that the posts are flush
步骤1：将立柱与门楣固定。
with the door head.
步骤2：将立柱与天窗连接板固定。
Step 1: Secure the posts to the door head.
步骤3：将立柱底部与机柜紧固。
Step 2: Secure the posts to the skylight connective plate.
步骤4：装上胶塞，完成安装。
Step 3: Secure the bottom of the posts to the cabinets.
Step 4: Install rubber plugs. The installation is complete.
安装门盒与立柱侧盖板
Installing Door Boxes and Side Covers for the Posts
5
4
1
2
2
步骤1：将PAD充电盒支撑件固定到门盒上。
步骤2：将PAD充电盒固定到支撑件上。
步骤3：面向通道，将标识"L"、"R"的门盒分别紧固在左右机柜顶部。
步骤4：将门盒内侧与立柱固定。
步骤5：将立柱侧面维护板装进立柱侧面。。
Step 1: Secure the pad charging box support on the door box.
Step 2: Secure the pad charging box on the support.
Step 3: Facing the aisle, secure the door box hanging kits labeled L and R to the
top of the left and right cabinets.
Step 4: Secure the door box interior to the post.
Step 5: Place the maintenance plate on the side of the column onto the side of the column.
天窗连接板 Skylight connective plate
4
3
A
B
06
安装PAD安装件
Installing a Pad Mounting Kit
3
M5x10
M5x10
1
3
4
3 N·m
3 N·m
M4x10
2
1.2 N·m
步骤1：将PAD安装件卡入门盒并固定。
步骤2：安装塑胶帽。
先布放PAD和门禁机的线缆后再固定PAD安装件。
Step 1: Install the pad mounting kit on the door box and secure it.
Step 2: Install the plastic cap.
NOTE
Route the cables of the pad and access control device,
and secure the pad mounting kit.
01
03
安装玻璃门
Installing a Glass Door
M6
1
3 N·m
M6
2
1
安装前，请拆除玻璃门上侧，下侧和中间的运输
保护胶条。
步骤1：安装门胶条。
步骤2：将玻璃门与立柱固定。
NOTE
Before installation, remove protective rubber strips
from the upper, middle, and lower parts of the glass
door.
Step 1: Install the door rubber strips.
Step 2: Secure the door panels to the door posts.
1
2
版权所有 © 华为技术有限公司2019。保留一切权利。
Copyright © Huawei Technologies Co., Ltd. 2019. All rights reserved.
Related Manuals for Huawei 21501043-003
Summary of Contents for Huawei 21501043-003
- Page 1 If the door gap is still uneven after the preceding measures are taken, remove, reinstall, and adjust the rubber strip 版权所有 © 华为技术有限公司2019。保留一切权利。 on one door panel until the door panel edges are in close contact. Copyright © Huawei Technologies Co., Ltd. 2019. All rights reserved.
- Page 2 Adjust them as shown by (3) and (4) in the figure. 调节电磁吸铁固定座和门板，保证双门电磁锁与电磁吸铁完全贴合， screws so that the white rubber washer is elastic. The washer will adjust the magnet to an appropriate position because of its elasticity. 保证偏差尽可能小，请按如图中的 所示方法调节。 版权所有 © 华为技术有限公司2019。保留一切权利。 Copyright © Huawei Technologies Co., Ltd. 2019. All rights reserved.