Bosch AUTODOME 7100i Installation Manual
  1. Manuals
  2. Brands
  3. Bosch Manuals
  4. Digital Camera
  5. AUTODOME 7100i
  6. Installation manual

Bosch AUTODOME 7100i Installation Manual

Hide thumbs Also See for AUTODOME 7100i:
Table of Contents

Quick Links

AUTODOME 7100i│AUTODOME 7100i IR
NDP‑7602‑Z40│ NDP‑7602‑Z40L│ NDP‑7604‑Z12L
en
Installation Manual
Table of Contents
loading

Related Manuals for Bosch AUTODOME 7100i

Summary of Contents for Bosch AUTODOME 7100i

  • Page 1 AUTODOME 7100i│AUTODOME 7100i IR NDP‑7602‑Z40│ NDP‑7602‑Z40L│ NDP‑7604‑Z12L Installation Manual...

  • Page 3: Table Of Contents

    Recommendations for third-party IEEE 802.3bt PoE Power Supply 11.4 Recommendations for 24 VAC Power Supply 11.5 Connecting liquid tight, electrically grounded metal conduit to Bosch Outdoor Midspans 11.6 (Optional) Support for Fiber optic cable installation 11.7 Connecting the Alarm Inputs and Alarm Relay Output 11.8...

  • Page 4: Safety

    Legal Information Copyright This manual is the intellectual property of Bosch Security Systems, and is protected by copyright. All rights reserved. Trademarks All hardware and software product names used in this document are likely to be registered trademarks and must be treated accordingly.

  • Page 5: Important Safety Instructions

    ® Electrical Code (NEC)), Canadian Electrical Code, Part I (also called CE Code or CSA C22.1), and all applicable local codes. Bosch Security Systems accepts no liability for any damages or losses caused by incorrect or improper installation. Warning! INSTALL EXTERNAL INTERCONNECTING CABLES IN ACCORDANCE TO NEC, ANSI/NFPA70 (FOR US APPLICATION) AND CANADIAN ELECTRICAL CODE, PART I, CSA C22.1 (FOR CAN...
  • Page 6 AUTODOME 7100i│AUTODOME 7100i IR Notice! Bosch recommends the use of surge/lightning suppression devices (sourced locally) to protect network and power cables and the camera installation site. Refer to NFPA 780, Class 1 & 2, UL96A, or the equivalent code appropriate for your country/region, and to local building codes.
  • Page 7 AUTODOME 7100i│AUTODOME 7100i IR Safety | en Notice! Risk of permanent damage to the camera The interface board connects only one way to the camera. Make sure that when you install it in the mount (arm or pipe mount), you install it the correct way.

  • Page 8: Important Notices

    Camera signal - Protect the cable with a primary protector if the camera signal is beyond 140 feet, in accordance with NEC800 (CEC Section 60) . Environmental statement - Bosch has a strong commitment towards the environment. This device has been designed to respect the environment as much as possible.
  • Page 9 AUTODOME 7100i│AUTODOME 7100i IR Safety | en Damage requiring service - Unplug the device from the main AC/DC/PoE power source and refer servicing to qualified service personnel when any damage to the equipment has occurred, such as: – the power supply cord or plug is damaged;...

  • Page 10: Connection In Applications

    802.3bt) are applied simultaneously, the camera selects PoE over the auxiliary input. For full feature support of the AUTODOME 7100i camera, an IEEE 802.3bt Type 3 60W midspan from Bosch should be used for non IR models and the IEEE 802.3bt Type 4 90W midspan should be used for IR models.

  • Page 11: Important Notices - Illumination Safety

    AUTODOME 7100i│AUTODOME 7100i IR Safety | en Important Notices - Illumination Safety The text in this section applies only to cameras that have illuminators. Notice! This product has been tested according to standard IEC 62471:2006 “Photobiological safety of lamps and lamp systems”. The product emissions exceed the EXEMPT Group limit for both Retinal Blue Light and Cornea/Lens infrared hazard as defined by IEC 62471:2006.

  • Page 12: Customer Support And Service

    | Safety AUTODOME 7100i│AUTODOME 7100i IR Customer Support and Service If this unit needs service, contact the nearest Bosch Security Systems Service Center for authorization to return and shipping instructions. USA and Canada Telephone: 800-289-0096, option 5 Fax: 800-366-1329 Email: [email protected]...

  • Page 13: Unpacking

    AUTODOME 7100i │ AUTODOME 7100i IR camera Quick Installation Guide Safety instructions MAC address labels Tools Required The table that follows is a list of additional products, sold separately by Bosch or other manufacturers, necessary to install AUTODOME cameras. Quantity Product Size Part Number...

  • Page 14: Product Description

    The design gives undistorted, high-resolution video above the horizon, which is helpful in city landscapes that are not flat. The camera has been designed for quick and easy installation, a key feature from Bosch IP video security products.

  • Page 15: Planning Information

    – SFP modules must meet the following temperature specifications that occur inside the AUTODOME 7100i mount: +85°C (+185°F) case temp. Copper power wire Make connections for 24VAC +/- 10%/36VDC. +/- 10% Belden cable or...

  • Page 16: Configuring The Camera Before Installation

    When you are configuring the camera in its packaging and you plan to install it on a pipe mount, you must use a complete Bosch pipe mount (NDA-7100-PIPE or NDA-7100-PIPEF) to supply power to the camera. It is the only way to make sure the board within the pipe mount is installed in the correct way.

  • Page 17: Installing The Camera Outdoors

    AUTODOME 7100i│AUTODOME 7100i IR Installing the camera outdoors | en Installing the camera outdoors Cameras installed outdoors are typically exposed to surges, transients, and lightning. The details for wiring and installation are based on common practices for proper surge and lightning suppression.
  • Page 18 | Installing the camera outdoors AUTODOME 7100i│AUTODOME 7100i IR 1 Indoor main building 2 Network switch with shielded ports and grounding as recommended by the manufacturer. All network cables must be terminated with shielded RJ45 connectors. 3 Surge suppression for indoor...
  • Page 19 If a metal pole is used, refer to NFPA 780, Class 1 & 2, UL96A, and to the equivalent code appropriate for the country/region. Camera Housings and Mounts – Use only Bosch mounts listed on the datasheet of the specific camera. – Follow all grounding for the camera housings and mounts per the installation manual. Bosch Security Systems...

  • Page 20: Preparing The Bubble

    Never scrub the bubble with any abrasive material or cleaners. Bosch recommends cleaning the exterior of the bubble with NOVUS “No. 1” Plastic Clean & Shine (or equivalent), according to manufacturer’s instructions. Refer to www.novuspolish.com...

  • Page 21: Optional) Installing An Sd Card

    Handle the bubble with care. Do not scratch the inside of the bubble which doesn’t have a hard coating. Notice! Use full size SD cards for maximum reliability. Bosch doesn’t recommend the use of microSD cards or of microSD to SD adapters. Notice! Before adding or removing a full size SD card from the camera, disconnect all power sources (including PoE) from the device.
  • Page 22 | (Optional) Installing an SD card AUTODOME 7100i│AUTODOME 7100i IR Replace the bubble. 10. Turn the bubble counterclockwise 10 degrees until it locks into position. 2023-02 | V01 | Bosch Security Systems Installation Manual...

  • Page 23: Installing A Pendant Arm Mount

    AUTODOME 7100i│AUTODOME 7100i IR Installing a pendant arm mount | en Installing a pendant arm mount Notice! Risk of water ingress If you: - remove a camera from its mount but do not replace it promptly, or - install the mount but do not install the camera immediately, then you must remove the PCB from the mount to avoid moisture or water ingress and potential corrosion.
  • Page 24 | Installing a pendant arm mount AUTODOME 7100i│AUTODOME 7100i IR Put the appropriate cables for power, video, alarms, and audio through one of the access holes in the wall mounting plate. Note: Use of proper grommets is needed, to guarantee IP66.
  • Page 25 AUTODOME 7100i│AUTODOME 7100i IR Installing a pendant arm mount | en Notice! Notice Use shielded twisted pair wire for all the connections such as a Belden cable with a foil shield: One shielded cable for: - 24VAC or 36VDC and GND...
  • Page 26 | Installing a pendant arm mount AUTODOME 7100i│AUTODOME 7100i IR NDA-7100-PIPEF NDA-7100-PENF Install the SFP module into the fiber port on the top of the mount. Push the SFP module into the port until you hear the catch engage.
  • Page 27 AUTODOME 7100i│AUTODOME 7100i IR Installing a pendant arm mount | en 13. Tilt the camera until you connect the camera to the mount. 14. Tighten the screws to 10-12 Nm. 15. Apply power. 16. Remove the protective plastic sheet from the bubble. Installation is complete.

  • Page 28: Installing A Pipe Mount

    | Installing a pipe mount AUTODOME 7100i│AUTODOME 7100i IR Installing a pipe mount Notice! Risk of water ingress If you: - remove a camera from its mount but do not replace it promptly, or - install the mount but do not install the camera immediately, then you must remove the PCB from the mount to avoid moisture or water ingress and potential corrosion.
  • Page 29 AUTODOME 7100i│AUTODOME 7100i IR Installing a pipe mount | en To make a watertight seal, wrap PTFE tape (user-supplied) four times around the threads at the end of the mount. 1.5”NPT PIPE Put the appropriate cables for power, video, alarms, and audio through one of the access holes in the wall mounting plate.
  • Page 30 | Installing a pipe mount AUTODOME 7100i│AUTODOME 7100i IR If you do not install fiber, skip to step 16. To install fiber, complete the 8 steps that follow. Remove the screws from the bottom of the pipe mount. NDA-7100-PIPEF NDA-7100-PENF Install the SFP module into the fiber port in the mount.
  • Page 31 AUTODOME 7100i│AUTODOME 7100i IR Installing a pipe mount | en NDA-7100-PIPEF NDA-7100-PENF Use a Torx wrench to install a grounding screw (user-supplied) on the grounding connection point on the bottom of the pipe mount, as in the figure that follows.

  • Page 32: Installing A Pipe Mount Onto A Nda-U-Rmt With Grounded Conduit

    | Installing a pipe mount AUTODOME 7100i│AUTODOME 7100i IR 15. Remove the protective plastic sheet from the bubble. Installation is complete. 10.1 Installing a pipe mount onto a NDA-U-RMT with grounded conduit Note: When installing the NDA-U-RMT mount, electrically grounded, liquid tight metal conduit must be used with extra grounding.
  • Page 33 AUTODOME 7100i│AUTODOME 7100i IR Installing a pipe mount | en Add a cable gland to seal around all the cables that exit the grounded conduit and enter the open pipe at the bottom of the NDA-U-RMT. Seal the bottom of the NDA-U-RMT pipe around the cables as liquid tight as possible.

  • Page 34: Connection

    Web server. In addition, power can be supplied over the Ethernet cable using a midspan from Bosch (IEEE 802.3bt Type 3/4 (60W/90W)) (sold separately). Power can also be supplied over the Ethernet cable and using PoE+ PSEs (midspans or switches) compliant with the IEEE 802.3bt, Type 3/4 (60W/90W) standard.
  • Page 35 AUTODOME camera IP Connection Network Switch Computer Figure 11.2: System Configuration: AUTODOME 7100i camera to midspan 1 AUTODOME camera 2 Midspan DATA & PWR OUT 3 IEEE 802.3bt Type 3/4 (60W/90W) midspan 4 Midspan DATA IN (to Ethernet switch or test PC)

  • Page 36: Connecting 24 Vac / 36 Vdc Power

    | Connection AUTODOME 7100i│AUTODOME 7100i IR 11.2 Connecting 24 VAC / 36 VDC Power Connect 24VAC +/- 10%, 50/60Hz or 36VDC +/- 10% to Connector X105 pins 1 and 2 as in the figure that follows. X104 X105 X106...

  • Page 37: Recommendations For Third-Party Ieee 802.3Bt Poe Power Supply

    Recommendations for third-party IEEE 802.3bt PoE Power Supply Bosch recommends the use of one of the IEEE 802.3bt Type 3 (60W) midspans for use with the non-IR AUTODOME camera model and one of the IEEE 802.3bt Type 4 (90W) midspans for use with the AUTODOME IR camera models.

  • Page 38: Recommendations For 24 Vac Power Supply

    11.4 Recommendations for 24 VAC Power Supply Bosch does not offer a 24VAC power supply accessory with enough power for the AUTODOME camera. A 24VAC, 50/60Hz power supply must meet the following requirements to be used with the AUTODOME camera.

  • Page 39: Optional) Support For Fiber Optic Cable Installation

    PENF and NDA-7100-PIPEF mounts must be removed before installing or removing an SFP module. Warning! The AUTODOME camera does not support BOSCH 100Mbps SFP fiber modules. Warning! If an SFP module is added to the NDA-7100-PENF or NDA-7100-PIPEF mount and connected to an AUTODOME camera, the Ethernet port in the camera will automatically be disabled, even if no fiber is connected to the SFP module.

  • Page 40: Connecting The Alarm Inputs And Alarm Relay Output

    | Connection AUTODOME 7100i│AUTODOME 7100i IR 11.7 Connecting the Alarm Inputs and Alarm Relay Output The Alarm Inputs and Alarm Output lines should use twisted pair wires with a foil shield where the drain wire of the foil shield is connected to the chassis/housing ground in the mount (NDA-7100-PIPE, NDA-7100-PIPEF, NDA-7100-PEN, NDA-7100-PENF) as described below.

  • Page 41: Troubleshooting

    M-JPEG display. If there is M-JPEG but not a STREAM1 or STREAM2 display in H.264 or H.265 then the problem might be with the BOSCH VideoSDK software version. - Check that there is adequate light in the video scene.
  • Page 42 - Trying pressing the Factory Default button. If Fiber optic output is used with NDA-7100-PIPEF or NDA-7100-PENF: - Check that a BOSCH 100Mbps SFP module isn’t being used since it is not supported. - Check that the SFP module supports 1.25Gbps.
  • Page 43 Camera reboots frequently or Your camera has an improper network connection. intermittently Test your camera with another power supply. Check the Bosch website for a software update that might address the issue. Bosch Security Systems 2023-02 | V01 | Installation Manual...

  • Page 44: Rebooting The Unit

    If you cannot control the unit after the firmware upgrade, then cycle the power to the unit. If a power reset does not solve the problem, or if Configuration or video management software identifies the unit as “Videojet Generic,” then contact your Bosch Service Center for an RMA for the unit.

  • Page 45: Maintenance

    Never scrub the bubble with any abrasive material or cleaners. Bosch recommends cleaning the exterior of the bubble with NOVUS “No. 1” Plastic Clean & Shine (or equivalent), according to manufacturer’s instructions. Refer to www.novuspolish.com...

  • Page 46: Technical Data

    | Technical data AUTODOME 7100i│AUTODOME 7100i IR Technical data For product specifications, see the datasheet for your camera, available on the appropriate product pages of the Online Product Catalog at www.boschsecurity.com. 2023-02 | V01 | Bosch Security Systems Installation Manual...

  • Page 47: Support Services And Bosch Academy

    Support services and Bosch Academy Support Access our support services at www.boschsecurity.com/xc/en/support/. Bosch Building Technologies Academy Visit the Bosch Building Technologies Academy website and have access to training courses, video tutorials and documents: www.boschsecurity.com/xc/en/support/training/ Bosch Security Systems 2023-02 | V01 |...
  • Page 48 | Support services and Bosch Academy AUTODOME 7100i│AUTODOME 7100i IR 2023-02 | V01 | Bosch Security Systems Installation Manual...
  • Page 49 AUTODOME 7100i│AUTODOME 7100i IR Support services and Bosch Academy | Bosch Security Systems 2023-02 | V01 | Installation Manual...
  • Page 50 | Support services and Bosch Academy AUTODOME 7100i│AUTODOME 7100i IR 2023-02 | V01 | Bosch Security Systems Installation Manual...
  • Page 52 Bosch Security Systems B.V. Torenallee 49 5617 BA Eindhoven Netherlands www.boschsecurity.com © Bosch Security Systems B.V., 2023 Building solutions for a better life. 202302272040...

This manual is also suitable for:

Autodome 7100i irNdp-7602-z40Ndp-7602-z40lNdp-7604-z12l

Table of Contents