Black & Decker FP1600, FP1700, FP1700B-CL, FP1800 - 8 Cup Food Processor Manual

Black & Decker FP1600, FP1700, FP1700B-CL, FP1800 - 8 Cup Food Processor Manual

Black & Decker FP1600, FP1700, FP1700B-CL, FP1800 - 8 Cup Food Processor Manual

OVERVIEW

Product may vary slightly from what is illustrated.

Overview

  1. Food pusher: FP1600B, FP1700B, FP1800B (Part # 20102000003802), FP1600WC (Part # 20102000003803)
  2. 8-cup processing workbowl cover: FP1600B, FP1700B, FP1800B (Part # 2050200590)
  3. Stainless steel slicing and shredding disk: FP1600B, FP1700B, FP1800B (Part # 2050200611)
  4. Center shaft FP1600B, FP1700B, FP1800B (Part # 2050200131)
  5. Stainless steel chopping blade: FP1600B, FP1700B, FP1800B (Part # 2050200621)
  6. 8-cup processing workbowl: FP1600B, FP1800B (Part # 2050200581), FP1700B (Part # 2050200800), FP1600WC (Part # 2050200631)
  7. Non-skid suction feet (Part # 09183-1)

Note: † indicates consumer replaceable/removable parts

Please Read and Save this Use and Care Book.

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed, including the following:

SAVE THESE INSTRUCTIONS.

This product is for household use only.
Note: The maximum rating is based on the chopping blade. Other attachments may draw significantly less power.

POLARIZED PLUG (120V MODELS ONLY)

This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to modify the plug in any way.

GROUNDED PLUG (220V MODELS ONLY)

As a safety feature, this product is equipped with a grounded plug, which will only fit into a three-prong outlet. Do not attempt to defeat this safety feature. Improper connection of the grounding conductor may result in the risk of electric shock. Consult a qualified electrician if you are in doubt as to whether the outlet is properly grounded.

TAMPER-RESISTANT SCREW


This appliance is equipped with a tamper-resistant screw to prevent removal of the outer cover. To reduce the risk of fire or electric shock, do not attempt to remove the outer cover. There are no user-serviceable parts inside. Repair should be done only by authorized service personnel.

ELECTRICAL CORD

  1. If an extension cord is used:

Note: If the power cord is damaged, please contact the warranty department listed in these instructions.

CONTROL PANEL

The controls are located on the front of the base (A).

Press OFF/PULSE (O/P) or ON (|) to select a function (see directions below).

OFF/PULSE CONTROL

ON CONTROL

When the ON control is selected, the processor will run continuously until the OFF/PULSE button is pressed.

HOW TO USE

This product is for household use only.

GETTING STARTED


Handle chopping blade and slicing and shredding disk carefully. They are very sharp.

ASSEMBLING THE PROCESSOR

  1. Place chopping blade or slicing/shredding disc onto post.

    chopping blade and slicing and shredding disk are very sharp. Use caution when handling and storing.
  2. Place cover on work bowl with the small latch to the right of the work bowl's handle, as shown in figure (G).
  3. Press the OFF/PULSE button and allow the blade/disk to come to a complete stop before removing cover by twisting cover toward . At this time, carefully remove the slicing/shredding disk.

HOW TO LOCK THE PROCESS OR WORKBOWL IN POSITION


Press the OFF/PULSE button before placing the workbowl on the base of the processor.

  1. Attach center post to base. Place the workbowl on the base with handle turned to the right of the locking mechanism (B) over the unlock symbol .
  2. Hold handle and rotate workbowl clockwise toward the lock symbol until it clicks firmly into place (C).
    Note: Be sure to lock the workbowl in place before attaching the chopping blade or the slicing and shredding disk and the cover.

HOW TO CHOP IN THE PROCESSING WORKBOWL

The chopping blade is used to coarsely or finely chop, mince, mix, and puree foods to a smooth consistency.

  1. Lock workbowl into position (see Illustrations B and C).
  2. Place chopper blade on center shaft, twist toward lock symbol (D).

    The chopping blade is very sharp. Use caution when handling and storing.
  3. Place cover on workbowl and lock into place by rotating clockwise (see Illustration G).
  4. Place the food pusher in place.

    Never use your fingers to direct food through the feed chute.
  5. Select your desired speed (PULSE or ON).
    Note: Process foods for no more than a few seconds at a time. Pulsing produces excellent results and offers greater control.

    Make sure the chopping blade has completely stopped spinning before removing cover from processing bowl.
  6. Press the OFF/PULSE button and allow the chopping blade to stop revolving before removing cover. Twist cover toward (counterclockwise) to remove.

    Unlock lid first before removing workbowl.
  7. Unlock workbowl by turning it counterclockwise and lift off base.
    Note: Remove workbowl from appliance before removing the chopping blade to prevent food from leaking through the center opening of the workbowl.

HOW TO SLICE OR SHRED IN THE WORKBOWL

  1. Lock workbowl into position (see Illustrations B and C).
  2. Carefully place slicing and shredding disk on top of center shaft with appropriate side up (depending on work to be done) (E).

    The slicing and shredding disk is very sharp. Use caution when handling and storing.
  3. Place cover on workbowl and lock into place by rotating cover clockwise (see Illustration G).
  4. Fill feed chute with food. Position food pusher over food (F).
  5. Select the PULSE or ON control; press firmly on food pusher to guide food through feed chute, but do not force it.
    Note: Heavy pressure on the pusher does not speed the work; use the pusher only as a guide. Let the processor do the work.
  6. When finished, press OFF/PULSE and wait for disk to stop rotating before removing cover. Twist cover toward counterclockwise to remove.

    Make sure the slicing and shredding disk has completely stopped spinning before removing cover from processing bowl.

    Unlock lid first before removing workbowl.

HOW TO LOCK THE COVER

  1. Place cover over workbowl with the small latch to the right of the workbowl's handle (G).
  2. Hold feed chute of workbowl cover and rotate cover clockwise until cover locks into place.

    For your protection this appliance has an interlock system. The processor will not operate unless the processing workbowl and cover are properly locked in place.
  3. Insert the food pusher into the feed chute.
    Note: The food pusher is used to guide foods through the feed chute and can be removed when adding liquid or additional foods while the processor is running.

HELPFUL TIPS

HELPFUL TIPS FOR CHOPPING

  • Do not overload the workbowl, past the "Max Liquid Level" mark (H).

HELPFUL TIPS WHEN SLICING AND SHREDDING

CARE AND CLEANING

This product contains no user serviceable parts. Refer service to qualified service personnel.

Note: Do not attempt to sharpen the cutting edges of the chopping blade or slicing and shredding disk. They are permanently sharpened at the factory and will be ruined if sharpened.

CLEANING

Note: Before cleaning, be sure unit is turned off and cord is unplugged.

  • Rinse parts immediately after processing for easy cleanup.

    The slicing and shredding disk is very sharp. Use caution when handling and storing.

STORAGE

Place stem and blade into bowl. Invert lid and place disk on top.

NEED HELP?

For service, repair or any questions regarding your appliance, call the appropriate 800 number on cover of this book. Please DO NOT return the product to the place of purchase. Also, please DO NOT mail product back to manufacturer, nor bring it to a service center. You may also want to consult the website listed on the cover of this manual.

TWO-YEAR LIMITED WARRANTY

(Applies only in the United States and Canada)

For how long?

How do you get service?

Customer Care Line: 1-800-465-6070
For online customer service: www.prodprotect.com/blackanddecker

Documents / Resources

References

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Table of Contents