SONY SA-VS500H - Home Theater Speaker System Manual

WARNING

To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To prevent fire, do not cover the ventilation of the apparatus with news papers, table-cloths, curtains, etc. And don't place lighted candles on the apparatus.

To prevent fire or shock hazard, do not place objects filled with liquids, such as vases, on the apparatus.
To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

Do not install the appliance in a confined space, such as a bookcase or built-in cabinet.

You are cautioned that any changes or modification not expressly approved in this manual could void your authority to operate this equipment.

About this manual

The SA-VS500H is a 5.1 channel speaker system consisting of two front speakers, two surround speakers, one center speaker, and one subwoofer. It supports Sony Digital Cinema Sound, Dolby* Pro Logic, and Dolby Digital etc., and is thus geared towards the enjoyment of movies.

* "Dolby" and the double-D symbol are trademarks of Dolby Laboratories.

Precautions

On safety

On operation

• The volume level should not be turned up to the point of distortion.

If you encounter color irregularity on a nearby TV screen

This speaker system is magnetically shielded to allow it to be installed near a TV set. However, color irregularities may still be observed on certain types of TV sets.

If color irregularity is observed...

If color irregularity is observed again...

If howling occurs

Reposition the speakers or turn down the volume on the amplifier.

On placement

• Do not place the speakers in locations that are:

On cleaning

Clean the speaker cabinets with a soft cloth lightly moistened with a mild detergent solution or water. Do not use any type of abrasive pad, scouring powder or solvent such as alcohol or benzine.

If you have any questions or problems concerning your speaker system, please consult your nearest Sony dealer.

Hooking up the system

Connect the speaker system to the speaker output terminals of an amplifier.

Make sure power to all components (included the subwoofer) is turned off before starting the hook-up.

Notes

• Make sure the plus (+) and the minus (–) terminals on the speakers are matched to the corresponding plus (+) and minus (–) terminals on the amplifier.
  
• Be sure to tighten the screws of the speaker terminals securely as loose screws may become a source of noise.
  
• Make sure all connections are firm. Contact between bare speaker wires at the speaker terminals may cause a short-circuit.
  

Tip
Black or black striped wires are minus (–) in polarity, and should be connected to the minus (–) speaker terminals.

Positioning the speakers

Location of each speaker

Each speaker should face the listening position. Better surround effect will result if all speakers are set at the same distance from the listening position.
Place the front speakers at a suitable distance to the left and right of the television.
Place the subwoofer on either side of the television.
Place the center speaker on the top-center of the TV set.
The placement of surround speakers greatly depends on the configuration of the room. The surround speakers may be placed on both sides of the listening position A or behind the listening position B.

Setting the center speaker

Set the center speaker firmly on top of the TV set, making sure it is completely level.

Note
Be sure to place the speaker in a flat, horizontal place.

Setting the amplifier

When connecting to an amplifier with internal multi channel decoders (Dolby Digital, DTS**, etc.), you should use the setup menus for the amplifier to specify the parameters of your speaker system.
See the table below for the proper settings. For details on the setting procedure, refer to the manual that was provided with your amplifier.

Speaker setup

If you use the amplifier with adjustable crossover frequency, it is recommended to select 150 Hz (or close to this figure) as the crossover frequency for your front, center, and surround speakers.

** "DTS" and "DTS Digital Surround" are registered trademarks of Digital Theater Systems, Inc.

Listening to the sound

First, turn down the volume on the amplifier. The volume should be set to minimum before you begin playing the program source.

Power turn on and off automatically

Auto power on/off function

When the subwoofer is on (i.e, the ON/STANDBY indicator lights up green) and there is no signal input for a few minutes, the ON/STANDBY indicator changes to red and the subwoofer enters power saving mode. While in this mode a signal is input to the subwoofer, the subwoofer automatically turns on (auto power on/off function). To turn this feature off, slide the POWER SAVE switch on the rear panel to OFF.

Note
If you turn down the volume level of the amplifier too low, the auto power on/off function may activate, causing the subwoofer to enter power saving mode.

Adjusting the subwoofer

Notes

Troubleshooting

Should you encounter a problem with your speaker system, check the following list and take the indicated measures. If the problem persists, consult your nearest Sony dealer.

There is not sound from the speaker system

There is distortion in the subwoofer sound output

There is hum or noise in the speaker output

The sound has suddenly stopped

Specifications

SS-VF500 (front and surround speakers)
Speaker system 2 way, magnetically shielded
Speaker units Woofer: 5.7 cm, cone type
Tweeter: 2.5 cm, balanced dome type
Enclosure type Bass reflex
Rated impedance 8 ohms
Power handling capacity
Maximum input power: 120 watts
Sensitivity level 84 dB (1 W, 1 m)
Frequency range 120 Hz - 50,000 Hz
Dimensions (w/h/d) Approx. 77 × 1,050 × 78 mm, including front grille, (Diameter of base: 250 mm)
Mass Approx. 6.0 kg

SS-CN500 (center speaker)
Speaker system 2 way, magnetically shielded
Speaker units Woofer: 5.7 cm, cone type
Tweeter: 2.5 cm, balanced dome type
Enclosure type Bass reflex
Rated impedance 8 ohms
Power handling capacity
Maximum input power: 120 watts
Sensitivity level 84 dB (1 W, 1 m)
Frequency range 120 Hz - 50,000 Hz
Dimensions (w/h/d) Approx. 336 × 82 × 84 mm, including front grille
Mass Approx. 1.6 kg

SA-WVS500 (subwoofer)
Speaker system Active subwoofer, magnetically shielded
Speaker unit Woofer: 20 cm, cone type
Enclosure type Advanced SAW type
Reproduction frequency range 26 Hz - 200 Hz
Continuous RMS power output 120 W (8 ohms 20 Hz - 20 kHz, 0.8% THD)

Inputs
LINE IN (input pin jack)

General
Power requirements 220 - 230 V AC, 50/60 Hz
Power consumptions 90 W
1 W (standby mode)
Dimensions (w/h/d) Approx. 230 × 392 × 447 mm, including front grille
Mass Approx. 13.2 kg

Supplied accessories
Audio connecting cord (1)
Speaker connecting cords, 10 m (2)
Speaker connecting cords, 3.5 m (3)

Design and specifications are subject to change without notice.

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.