Thank you for purchasing this PIONEER product
To ensure proper use, please read through this guide before using this product. It is especially important that you read and observe WARNINGS and CAUTIONS in this guide. Please keep the guide in a safe and accessible place for future reference.
Information for users on collection and disposal of old equipment and used batteries
(Symbol for equipment)
(Symbol examples for batteries)
These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste.
For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points in accordance with your national legislation.
By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products and batteries, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items.
These symbols are only valid in the European Union.
For countries outside the European Union:
If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal.
This unit provides a variety of sound effects by intuitive operation using a smartphone.
Remove the insulation sheet before use.
How to replace the battery
Insert the battery with the plus (+) and minus (–) poles orientated properly.
Cut the attached power cord and then connect it to the vehicle.
The wiring harness kit (sold separately) is also available to connect the cord.
Connect the car stereo speaker output wires to this unit using the power cord. Slide the INPUT select switch to the SP position.
Note:
Connect the car stereo RCA output jack and the RCA input jack of this unit. Slide the INPUT select switch to the RCA position.
Note
Connect to the parking brake switch using the parking brake cord.
Note: When the parking brake cable is not connected, a part of the exclusive application (Sound Tune) function is limited.
Place the light receiving part of the remote control sensor in a place that can receive the remote control signal.
Wire the cable so that it does not interfere with driving.
To use this unit, download Sound Tune to the iPhone or smartphone (Android). Enter the search term "Pioneer Sound Tune" in the search window or search from the following QR code.
Do not attempt to operate the application while driving. Make sure to pull off the road and park your vehicle in a safe location before attempting to use the controls on the application.
Sound Tune can do the following.
Playing songs saved on iPhone / smartphone (Android)
Playable song formats depend on your device. For details, please read the instruction manual of your device.
Effect settings of iPhone / smartphone (Android) songs and the car stereo / navigation system sound
Various settings of this unit
For details of each function, please refer to Popup Help in Sound Tune.
Depending on the connection method of the iPhone / smartphone (Android), this unit can be used as follows.
The unit outputs the sound source of the car stereo / navigation system. Only the volume adjustment and mute functions can be operated with the supplied remote control.
For audio adjustment, connection of an iPhone / smartphone (Android) is necessary.
The unit can be used in the following four pattern modes.
When using the remote control, press the SRC button to switch the mode. The mode switches in the order of Car Stereo mode, Through mode, Smartphone mode, and Mix mode.
Car Stereo mode
The unit outputs the sound source of the car stereo / navigation system by passing through the iPhone / smartphone (Android).
Smartphone mode
The unit outputs the sound source of the iPhone / smartphone (Android).
Through mode
The unit outputs the sound source of the car stereo / navigation system without passing through the iPhone / smartphone (Android). (It is the same output as using this unit alone)
This mode is used when video and audio are misaligned during video playback in the Car Stereo mode.
Mix mode
The unit mixes and outputs the sound of the iPhone / smartphone (Android) and the sound of the car stereo / navigation system.
Use this mode when you want to use the voice guidance of the car stereo / navigation system while listening to the source of the iPhone / smartphone (Android). In this case, turn off the source of the car stereo / navigation system and set it so that only the voice guidance is output.
Depending on the car stereo / navigation system, this mode may not be available.
The available functions differ depending on the connection method of the iPhone / smartphone (Android).
Device | iPhone | Smartphone (Android) | |
Connection method | - | AOA*1 | OTG*2 |
Car Stereo mode | -(*3) | ||
Smartphone mode | (*4) | ||
Through mode | |||
Mix mode | (*4) |
Note:
For iPhone users
For smartphone (Android) users (AOA connection)
For smartphone (Android) users (OTG connection)
Note: Smartphone (Android) cannot be charged using the OTG connection.
When connecting an iPhone or smartphone (Android) to this unit, a message is displayed on the iPhone or smartphone (Android). Sound Tune starts when startup is allowed.
Tap the icon at the bottom of the screen to start the operation.
Reset this unit if it does not operate properly or you want to return the setting value to the factory default.
If you cannot hear the sound after installing this unit, carry out the following.
This product has a protection function. When this product detects something abnormal, the following functions will operate to protect the product and speaker output.
Please contact your dealer or service agent if improvements are not made even after you try turning the ACC switch OFF / ON or removing/reinserting the USB.
POWER SOURCE | 14.4V DC (10.8-15.1V allowable) |
GROUNDING SYSTEM | Negative type |
MAX. CURRENT CONSUMPTION | 9.2A |
DIMENSIONS | 170(W) x 40(H) x 95(D) |
FUSE | 10A |
WEIGHT | 0.59kg |
MAX POWER | 50W x 4 50Wx2ch/4Ω + 70Wx1ch/2Ω (for SUB-WOOFER) |
CONTINUOUS POWER | 22W x 4 (50Hz to 15kHz, 5%THD, 4Ω LOAD, Both Channels Driven) |
LOAD IMPEDANCE | 4Ω (4 - 8Ω(2Ω for 1ch) allowable) |
PREOUT | |
OUTPUT LEVEL (MAX) | 4.0V |
IMPEDANCE | 250Ω |
FREQUENCY RESPONSE | 10Hz to 20kHz (+0dB, -1dB) |
S/N RATIO | 105dB |
THD | 0.01% |
EQUALIZER (13BAND GRAPHIC EQUALIZER) | |
FREQUENCY | 50Hz, 80Hz, 125Hz, 200Hz, 315Hz, 500Hz 800Hz, 1.25kHz, 2kHz, 3.15kHz, 5kHz, 8kHz, 12.5kHz |
GAIN | ±12dB(0.1dB step) |
FRONT/REAR (HPF) | |
FREQUENCY | 50Hz, 63Hz, 80Hz, 100Hz, 125Hz, 160Hz, 200Hz |
SLOPE | 0dB(Pass), -6dB/oct, -12dB/oct, -18dB/oct, -24dB/oct |
SUB WOOFER (LPF) | |
FREQUENCY | 50Hz, 63Hz, 80Hz, 100Hz, 125Hz, 160Hz, 200Hz |
SLOPE | 0dB(Pass), -6dB/oct, -12dB/oct, -18dB/oct, -24dB/oct |
GAIN | -24 - +10dB (1dB/Step) |
PHASE | NORMAL/REVERSE |
SPEAKER LEVEL | -24 - +10dB (1dB/Step) |
TIME ALIGNMENT | 0cm - 350cm (2.5cm/step) |
HIGH (HPF) | |
FREQUENCY | 1.25kHz, 1.6kHz, 2kHz, 2.5kHz, 3.15kHz 4kHz, 5kHz, 6.3kHz, 8kHz, 10kHz, 12.5kHz |
SLOPE | -6dB/oct, -12dB/oct, -18dB/oct, -24dB/oct |
MID (LPF) | |
FREQUENCY | 1.25kHz, 1.6kHz, 2kHz, 2.5kHz, 3.15kHz 4kHz, 5kHz, 6.3kHz, 8kHz, 10kHz, 12.5kHz |
SLOPE | 0dB(Pass), -6dB/oct, -12dB/oct, -18dB/oct, -24dB/oct |
MID (HPF) | |
FREQUENCY | 25Hz, 31.5Hz, 40Hz, 50Hz, 63Hz, 80Hz 100Hz, 125Hz, 160Hz, 200Hz, 250Hz |
SLOPE | 0dB(Pass), -6dB/oct, -12dB/oct, -18dB/oct, -24dB/oct |
SUB WOOFER (LPF) | |
FREQUENCY | 25Hz, 31.5Hz, 40Hz, 50Hz, 63Hz, 80Hz 100Hz, 125Hz, 160Hz, 200Hz, 250Hz |
SLOPE | 0dB(Pass), -12dB/oct, -18dB/oct 24dB/oct, -30dB/oct, -36dB/oct |
GAIN | -24 - +10dB (1dB/Step) |
PHASE | NORMAL/REVERSE |
SPEAKER LEVEL | -24 - +10dB (1dB/Step) |
TIME ALIGNMENT | 0cm - 350cm (2.5cm/step) |
USB STANDARD SPEC. | USB2.0 High Speed |
MAX CURRENT SUPPLY | 1.5A |
http://www.pioneer-car.eu
iPhone, and Lightning are trademarks of Apple Inc., registered in the U.S. and other countries.
Use of the Made for Apple badge means that an accessory has been designed to connect specifically to the Apple product(s) identified in the badge, and has been certified by the developer to meet Apple performance standards.
Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
Please note that the use of this accessory with an Apple product may affect wireless performance.
Visit www.pioneer-car.co.uk (or www.pioneer-car.eu) to register your product.
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.