Related Manuals for Electrolux WTB4600
Summary of Contents for Electrolux WTB4600
- Page 1 WTB4600, KTM4602, WTB5400, KTM5402, WBE4500, KBM4502, WBE5300, KBM5302, WFB4204, WRB5004 Refrigeration Installation manual IK008 Integration kit...
-
Page 2: Table Of Contents
After unpacking the integration kit, please check it is not damaged. If in doubt, do not use the integration kit but Securing refrigerator in cupboard ......13 contact your local Electrolux Customer Care Centre. Attaching slide-bar to cupboard door ....13 Notes ..............15... -
Page 3: Refrigerator Integration Kit Items
DESCRIPTION REFRIGERATOR INTEGRATION KIT ITEMS Because this kit is common to a variety of models, you need to select the items required to suit your model. The items required for the models covered in this instruction booklet are shown below. Those items not required on your particular model should be discarded. -
Page 4: Cupboard Dimensions
Dim ‘H’ Dim ‘I’* Model (mm) min. (mm) (mm) (mm) (mm) (mm) (mm) (mm) 2 door top freezer models WTB4600, WTB4604, 1820 1217 KTM4602 WTB5400, WTB5404, 1820 1217 Please KTM5402 use the calculation 2 door bottom freezer models below to... - Page 5 NOTE: All sizes are internal and measured in millimetres. For ‘lettered’ dimensions refer to the table on page 4. Dim B Dim C + 2x Board thickness Panel A Panel B (sides) (back) 100mm Dim E Dim H Panel C Panel D (top) (bottom)
- Page 6 DIMENSIONS (CONTINUED) When positioned in a corner the clearance of Dim G on Clearances the hinge side of the cabinet will allow the doors to be When installed the opened enough to enable the removal of the crisper bins.
-
Page 7: Installation Of 120˚ Hinge
INSTALLATION INSTALLATION OF 120˚ HINGE Preparation Unpack refrigerator, removing foam packing. Please follow the instructions below to install the Lay the refrigerator down on its back on a piece of 120º hinge. soft packing material. Use caution and two people while laying the appliance down. -
Page 8: Attaching The Rear Rollers
INSTALLATION (CONTINUED) ATTACHING THE REAR ROLLERS Once fitted turn the adjusting nut on each roller assembly anti-clockwise three full turns, this will raise the cabinet at the rear by approximately 12mm (ensure that the nut is A set of adjustable back feet/rollers is provided in the kit. -
Page 9: Attaching Top Hinge Bracket
ATTACHING THE TOP HINGE Figure 4 BRACKET Remove top hinge cover (Figure 3), cover clips off. Remove the three (3) top hinge screws. Elevate hinge. 12mm Slide the top hinge bracket into position below the hinge. Re-attach hinge and screws ensuring that refrigerator door is still correctly positioned. -
Page 10: Attaching Slide-Housing To Refrigerator Doors
INSTALLATION (CONTINUED) ATTACHING SLIDE-HOUSING TO slide housing REFRIGERATOR DOORS protuding edge Ensure slide-housing is positioned squarely as shown. 100mm Ensure that the slide-housing is positioned on the door as shown in the diagrams. NOTE: The slide-housing ‘protruding edge’ side must door handle always be closest to the door handle side (diagram right). -
Page 11: Placing Refrigerator In Cupboard
NOTE: For single door models, the door handle must be completely removed to provide clearance to the cupboard door and the resulting handle mounting holes hidden with a cover. Installer must use a tape or plastic cover that suits the installation appearance (not supplied). While the slide-housing is taped in position, punch a small hole in the refrigerator door skin corresponding to the four (4) holes in the housing (Figure 5). -
Page 12: Refrigerator Alignment
INSTALLATION (CONTINUED) REFRIGERATOR ALIGNMENT Figure 9a - Hinge side Position the refrigerator in the cupboard so that: Top hinge bracket is against cupboard wall (Figure 8). Front of refrigerator cabinet (with doors open) is parallel to and approximately 100mm from the front of the cupboard (Figure 9). -
Page 13: Securing Refrigerator In Cupboard
SECURING THE REFRIGERATOR IN ATTACHING SLIDE-BAR TO THE THE CUPBOARD CUPBOARD DOOR NOTE: When attaching all screws to cupboard, first drill Fully open cupboard door (120°). a 2mm pilot hole in the correct position. This will allow Open refrigerator door until it rests against the easy hand insertion of self tapping screw. - Page 14 INSTALLATION (CONTINUED) Rotate slide-bar to lower alignment, mark a line on cupboard door (Figure 16). Figure 16 Remove slide-bar and draw line to indicate central alignment (Figure 17). Figure 17 Replace slide-bar and align to centre line marked in previous operation (Figure 18).
-
Page 15: Notes
NOTES... - Page 16 0800 436 245 fax: 0800 225 088 email: [email protected] web: electrolux.co.nz To add a touch of professional inspiration to your home, visit electrolux.com.au or electrolux.co.nz P/No. A04633101 © 2015 Electrolux Home Products Pty Ltd. ABN 51 004 762 341 EMAN_IK008_Sep15...