Pioneer MVH-MS410BT - Marine Media Receiver Quick Start Guide

If your boat's ignition has no ACC position, some settings are not saved to the memory. To save, detach the front panel or wait for the unit to shut off completely for 10 seconds after turning it off by pressing and holding SRC/OFF (when [ON] is selected in [PW SAVE]), then turn the ignition off.

This guide is intended to guide you through the basic functions of this unit. For details, please refer to the Operation manual stored on the website. https://www.pioneer-car.eu/eur/

To cancel the demonstration display (DEMO OFF), refer to "Canceling the demonstration display (DEMO OFF)".

Before You Start

To ensure proper use, please read through this guide before using this product. It is especially important that you read and observe WARNINGS and CAUTIONS in this guide. Please keep the guide in a safe and accessible place for future reference.

If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.

Private households in the member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to designated collection facilities or to a retailer (if you purchase a similar new one).
For countries not mentioned above, please contact your local authorities for the correct method of disposal. By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.

• Do not attempt to install or service this product by yourself. Installation or servicing of this product by persons without training and experience in electronic equipment and automotive accessories may be dangerous and could expose you to the risk of electric shock, injury or other hazards.

If you experience problems
Should this unit fail to work properly, please contact your dealer or nearest authorized PIONEER Service Station.

Connections

• Warning if your boat's ignition has no ACC position Be sure to set [PW SAVE] to [ON] (for details, refer to the Operation manual). The unit will automatically shut off completely in 10 seconds after turning it off by pressing and holding SRC/OFF to prevent battery drain.

• When installing this unit in a boat without an ACC (accessory) position on the ignition switch, failure to connect the red cable to the terminal that detects operation of the ignition key may result in battery drain.
  
• Use of this unit in conditions other than the following could result in fire or malfunction.
  • When rear speaker output is used by 2 Ω of subwoofer, use speakers over 70 W (maximum input power).
    * Please refer to connections for a connection method.
• To prevent a short-circuit, overheating or malfunction, be sure to follow the directions below.
• The graphical symbol placed on the product means direct current.

This unit

1. Wired remote input
   Pioneer marine wired remote control (CD-ME300) can only be connected (sold separately).

Power cord

Perform these connections when not connecting a rear speaker lead to a subwoofer.

Perform these connections when using a subwoofer without the optional amplifier.

In the case of above, two 4 Ω subwoofers wired in parallel will represent a 2 Ω load.

1. Black (chassis ground)
   Connect to a common ground point.
2. Yellow
   Connect to the constant 12 V supply terminal.
3. Red
   Connect to terminal controlled by the ignition switch (12 V DC).
4. Blue/white
   Connect to the system control terminal of the power amp or auto-antenna relay control terminal (max. 300 mA 12 V DC).

Power amp (sold separately)

Perform these connections when using the optional amplifier.

1. System remote control
   Connect to blue/white cable.

Installation

• To customer:
  This product includes a radio transmitter. According to UNECE Regulation no. 10, vessel manufacturers may impose specific conditions for the installation of radio transmitters into boats. Please check your boat's operation manual or contact the manufacturer or your boat dealer before you install this unit.

• Do not install this unit where:
• Optimum performance is obtained when the unit is installed at an angle of less than 60°.
  
• When installing, to ensure proper heat dispersal when using this unit, make sure you leave ample space behind the rear panel and wrap any loose cables so they are not blocking the vents.
  

DIN mount installation

1. Insert the supplied mounting sleeve into the dashboard.
2. Secure the mounting sleeve by using a screwdriver to bend the metal tabs (90°) into place.
   

When not using the supplied mounting sleeve

1. Line up the holes on the mounting bracket with the holes on the sides of the unit to attach the bracket.
   
   
2. Screw in one screw on each side to hold the unit in place.
   

Using the included bracket

Check to make sure that the included bracket matches your particular model of boat and then attach it to the unit as shown below.

Removing the unit (installed with the supplied mounting sleeve)

1. Remove the trim ring.
   
2. Insert the supplied extraction keys into both sides of the unit until they click into place.
3. Pull the unit out of the dashboard.
   

Installing the microphone

The microphone should be placed directly in front of the driver at a suitable distance to pick up their voice clearly.

1. Slide the microphone base to detach it from the microphone clip.
   
2. Install the microphone as follows.
   

Basic operation

MVH-MS410BT

About the main menu

You can adjust various settings in the main menu.

1. Press the M.C. dial to display the main menu.
2. Turn the M.C. dial to select one of the categories below, then press to confirm.
3. Turn the M.C. dial to select the options, then press to confirm.

Frequently used operations

Purpose	Operation
Turn on the power	Press SRC/OFF to turn on the power. Press and hold SRC/OFF to turn off the power.
Adjust the volume	Turn the M.C. dial.
Select a source	Press SRC/OFF repeatedly.
Change the display information	Press DISP repeatedly.
Return to the previous display/list	Press BAND/.
Return to the normal display from the menu	Press and hold BAND/.
Change the display brightness	Press and hold BAND/.

Setup operation

When you turn the ignition switch to ON after installation, the setup menu appears in the display.

1. Turn the M.C. dial to select the options, then press to confirm.
   To proceed to the next menu option, you need to confirm your selection.

   Menu Item		Description
   LANGUAGE [ENG](English), [РУС](Russian), [TUR](Turkish), [FRA](French), [DEU](German)		Select the language to display the text information from a compressed audio file.
   CLOCK SET		Set the clock. Turn the M.C. dial to adjust the hour, then press to confirm. The indicator moves to the minute setting automatically. Turn the M.C. dial to adjust the minute, then press to confirm.
   FM STEP [100], [50]		Select the FM tuning step from 100 kHz or 50 kHz.

2. [QUIT:YES] appears.
   To return to the first item of the setup menu, turn the M.C. dial to select [QUIT:NO], then press to confirm.
3. Press the M.C. dial to confirm the settings.

Canceling the demonstration display (DEMO OFF)

1. Press the M.C. dial to display the main menu.
2. Turn the M.C. dial to select [SYSTEM], then press to confirm.
3. Turn the M.C. dial to select [DEMO OFF], then press to confirm.
4. Turn the M.C. dial to select [YES], then press to confirm.

Tuner operation

Receiving preset stations

1. Press SRC/OFF to select [RADIO].
2. Press BAND/ to select the band.
   [FM1] [FM2] [FM3] [MW]/[LW]
3. Press a number button (1/ to 6/).

Best stations memory (BSM)

1. After selecting the band, press the M.C. dial to display the main menu.
2. Turn the M.C. dial to select [FUNCTION], then press to confirm.
3. Turn the M.C. dial to select [BSM], then press to confirm.

To store stations manually

1. While receiving the station you want to store, press and hold one of the number buttons (1/ to 6/) until it stops flashing.

USB/iPhone^®/AUX operation

(iPhone source is not available when [USB MTP] is set to [ON] in the SYSTEM settings.)

USB/iPhone

MTP connection

A device installed with Android OS 4.0 or most of later versions can be connected to the unit via MTP, using the cable supplied with the Android device. However, depending on the connected device, OS version or the numbers of the files in the device, audio files/songs may not be able to be played back via MTP.

NOTE
If you use an MTP connection, [USB MTP] needs to be set to [ON] in the SYSTEM settings.

AUX

1. Press SRC/OFF to select [AUX IN] as the source.

Bluetooth connection

Up to two Bluetooth telephones can be connected simultaneously.

Bluetooth telephone

Basic operations

Purpose	Operation
Answer an incoming call	Press any button when a call is received.
End a call	Press .
Reject an incoming call	Press and hold when a call is received.

Activating voice recognition mode

1. Press and hold and then talk into the microphone to input voice commands.

To exit the voice recognition mode, press BAND/.

Making a connection with Pioneer Smart Sync

Pioneer Smart Sync is the application that intelligently brings your favorite marine application, messages, and music together in the boat.

Do not attempt to operate the application while driving. Make sure to stop your boat in a safe location before attempting to use the controls on the application.

1. Turn the M.C. dial to select [APP CONTROL], then press to confirm.
2. Turn the M.C. dial to select one of the below.
3. Turn the M.C. dial to select [AUTO APP CONN], then press to confirm.
4. Turn the M.C. dial to select [ON], then press to confirm.

NOTE
Regardless of whether the [AUTO APP CONN] setting is set to [ON] or [OFF], you can also perform the following to start Pioneer Smart Sync.

• For devices other than the USB-connected Android device, press SRC/OFF to select any source and press and hold the M.C. dial.

Listening to Spotify^®

(Not available when [USB MTP] is set to [ON] in the SYSTEM settings.)

Update the firmware of the Spotify application to the latest version before use.
Before you start, connect this unit with the mobile device via USB (iPhone only) or Bluetooth.

1. Turn the M.C. dial to select [APP CONTROL], then press to confirm.
2. Turn the M.C. dial to select one of the below.
3. Press SRC/OFF to select [SPOTIFY].

Declaration of Conformity with regard to the Radio Equipment Directive 2014/53/EU

Manufacturer: Pioneer Corporation 28-8, Honkomagome 2-chome, Bunkyo-ku, Tokyo 113-0021, Japan

EU Representative's & Importer: Pioneer Europe NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium http://www.pioneer-car.eu

Hereby, Pioneer declares that the radio equipment type [*] is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address: http://www.pioneer-car.eu/compliance

[*] MVH-MS410BT