Pioneer DEH-S5200BT, DEH-S4220BT, DEH-S4200BT Quick Start Guide

Pioneer DEH-S5200BT, DEH-S4220BT, DEH-S4200BT Quick Start Guide

Also See for DEH-S5200BT:
Pioneer DEH-S5200BT, DEH-S4220BT, DEH-S4200BT Quick Start Guide

Before You Start

To ensure proper use, please read through this guide before using this product. It is especially important that you read and observe WARNINGS and CAUTIONS in this guide. Please keep the guide in a safe and accessible place for future reference.

FCC ID: EW4C95
MODEL NO.: DEH-S5200BT/DEH-S4220BT/DEH-S4200BT
IC: 4250A-C95

This device contains licence-exempt transmitter(s)/receiver(s) that complies with Part 15 of FCC Rules and Innovation, Science, and Economic Development Canada licence-exempt RSS(s). Operation is subject to the following two conditions:

This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
The Bluetooth antenna cannot be removed (or replaced) by user.
This equipment complies with FCC/ISED radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the ISED radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated keeping the radiator at least 20cm or more away from person's body (excluding extremities: hands, wrists, feet and ankles).
Alteration or modifications carried out without appropriate authorization may invalidate the user's right to operate the equipment.

Note
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

FEDERAL COMMUNICATIONS COMMISSION SUPPLIER'S DECLARATION OF CONFORMITY
Product Name: CD RDS RECEIVER
Model Number: DEH-S5200BT/DEH-S4220BT/DEH-S4200BT
Responsible Party Name: PIONEER ELECTRONICS (USA), INC. SERVICE SUPPORT DIVISION Address: 2050 W. 190TH STREET, SUITE 100 TORRANCE, CA 90504, U.S.A.
Phone: 1-310-952-2915
URL: http://www.pioneerelectronics.com

The Safety of Your Ears is in Your Hands
Get the most out of your equipment by playing it at a safe level—a level that lets the sound come through clearly without annoying blaring or distortion and, most importantly, without affecting your sensitive hearing. Sound can be deceiving.
Over time, your hearing "comfort level" adapts to higher volumes of sound, so what sounds "normal" can actually be loud and harmful to your hearing. Guard against this by setting your equipment at a safe level BEFORE your hearing adapts.

ESTABLISH A SAFE LEVEL:

BE SURE TO OBSERVE THE FOLLOWING GUIDELINES:


This product is a Class 1 laser product classified under the safety standard, IEC 60825-1:2014.


USE OF CONTROL OR ADJUSTMENT OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.


THE USE OF OPTICAL INSTRUMENTS WITH THIS PRODUCT WILL INCREASE EYE HAZARD.

After-sales service for Pioneer products
Please contact the dealer, distributor from where you purchased this unit or the authorized PIONEER Service Station for after-sales service or any other information. In case the necessary information is not available, please contact the companies listed below:
Please do not ship your unit to the companies at the addresses listed below for repair without contacting them in advance.

U.S.A. and CANADA
Pioneer Electronics (USA) Inc.
CUSTOMER SUPPORT DIVISION
P.O. Box 1760
Long Beach, CA 90801-1760
800-421-1404

For warranty information please see the Limited Warranty sheet included with this unit.

Connections

  • When rear speaker output is used by a 2 Ω subwoofer, use speakers rated for over 70 W.
    * Please refer to connections for a connection method.
  • The black cable is ground. When installing this unit or power amp (sold separately), make sure to connect the ground wire first. Ensure that the ground wire is properly connected to metal parts of the car's body. The ground wire of the power amp and the one of this unit or any other device must be connected to the car separately with different screws. If the screw for the ground wire loosens or falls out, it could result in fire, generation of smoke or malfunction.
    Two devices connected to the car separately (ground wires)
    Two devices connected to the car separately
    *1 Not supplied for this unit

  • When installing this unit in a vehicle without an ACC (accessory) position on the ignition switch, failure to connect the red cable to the terminal that detects operation of the ignition key may result in battery drain.

  • To prevent a short-circuit, overheating or malfunction, be sure to follow the directions below.
  • The graphical symbol placed on the product means direct current.

This unit

Overview

Power cord

Perform these connections when not connecting a rear speaker lead to a subwoofer.
Power cord - Part 1

Perform these connections when using a subwoofer without the optional amplifier.
Power cord - Part 2


In the case of above, two 4 Ω subwoofers wired in parallel will represent a 2 Ω load.

  1. Black (chassis ground)
    Connect to a clean, paint-free metal location.
  2. Yellow
    Connect to the constant 12 V supply terminal.
  3. Red
    Connect to terminal controlled by the ignition switch (12 V DC).
  4. Blue/white
    Connect to the system control terminal of the power amp or auto-antenna relay control terminal (max. 300 mA 12 V DC).

Power amp

(sold separately)

Perform these connections when using the optional amplifier.
DEH-S4220BT/S4200BT
Power amp - Part 1

DEH-S5200BT
Power amp - Part 2

Installation

  • Do not install this unit where:
  • Optimum performance is obtained when the unit is installed at an angle of less than 60°.

  • When installing, to ensure proper heat dispersal when using this unit, make sure you leave ample space behind the rear panel and wrap any loose cables so they are not blocking the vents.
    Installation

DIN mount installation

DIN mount installation - Step 1

  1. Insert the supplied mounting sleeve into the dashboard.
  2. Secure the mounting sleeve by using a screwdriver to bend the metal tabs (90°) into place.
  1. Mounting sleeve

When not using the supplied mounting sleeve

  1. Determine the appropriate position where the holes on the bracket and the side of the unit match.
    DIN mount installation - Step 2
  2. Tighten the screws on each side.
    DIN mount installation - Step 3
    1. Dashboard or console

Removing the unit (installed with the supplied mounting sleeve)

  1. Remove the trim ring.
    Removing the unit - Step 1
    1. Notched tab
  2. Insert the supplied extraction keys into both sides of the unit until they click into place.
  3. Pull the unit out of the dashboard.
    Removing the unit - Step 2

To secure the front panel

The front panel can be secured with the supplied screw.
To secure the front panel

Installing the microphone

The microphone should be placed directly in front of the driver at a suitable distance to pick up their voice clearly.


It is extremely dangerous to allow the microphone lead to become wound around the steering column or shift lever. Be sure to install the microphone in such a way that it will not obstruct driving. It is recommended to use the clamps (sold separately) to arrange the lead.

NOTE
Depending on the vehicle model, the microphone cable length may be too short when you mount the microphone on the sun visor. In such cases, install the microphone on the steering column.

To install on the sun visor

  1. Fit the microphone lead into the groove.
    To install on the sun visor - Step 1
  2. Install the microphone clip on the sun visor.
    Lowering the sun visor reduces the voice recognition rate.
    To install on the sun visor - Step 2

To install on the steering column

  1. Slide the microphone base to detach it from the microphone clip.
    To install on the steering column - Step 1
  2. Install the microphone on the rear side of the steering column.
    To install on the steering column - Step 2

Basic operation

DEH-S5200BT
Basic operation - DEH-S5200BT

DEH-S4220BT/S4200BT
Basic operation - DEH-S4220BT/S4200BT

About the main menu

You can adjust various settings in the main menu.

  1. Press the M.C. dial to display the main menu.
  2. Turn the M.C. dial to select one of the categories below, then press to confirm.
  1. Turn the M.C. dial to select the options, then press to confirm.

Frequently used operations

Purpose Operation
Turn on the power Press SRC/OFF to turn on the power.
Press and hold SRC/OFF to turn off the power.
Adjust the volume Turn the M.C. dial.
Select a source Press SRC/OFF repeatedly.
Change the display information Press DISP repeatedly.
Return to the previous display/list Press BAND/ .
Return to the normal display from the menu Press and hold BAND/ .
Change the display brightness Press and hold BAND/ .
Boost the bass level Press BASS.

Setup operation

When you turn the ignition switch to ON after installation, the setup menu appears in the display.

  1. Turn the M.C. dial to select [LANGUAGE], then press to confirm.
    [ENG] [ESP] [FRA]
  2. Turn the M.C. dial to select [CLOCK SET], then press to confirm.
    1. Turn the M.C. dial to adjust the hour, then press to confirm. The indicator moves to the minute setting automatically.
    2. Turn the M.C. dial to adjust the minute, then press to confirm.
  3. 3 [QUIT:YES] appears.
    To return to the first item of the setup menu, turn the M.C. dial to select [QUIT:NO], then press to confirm.
  4. Press the M.C. dial to confirm the settings.

Tuner operation

Receiving preset stations

  1. Press SRC/OFF to select [RADIO].
  2. Press BAND/ to select the band.
    [FM1] [FM2] [FM3] [AM]
  3. 3 Press a number button (1/ to 6/ ).

Best stations memory (BSM)

  1. After selecting the band, press the M.C. dial to display the main menu.
  2. Turn the M.C. dial to select [FUNCTION], then press to confirm.
  3. Turn the M.C. dial to select [BSM], then press to confirm.

To store stations manually

  1. While receiving the station you want to store, press and hold one of the number buttons (1/ to 6/) until it stops flashing.

CD/USB/iPhone®/AUX operation

(iPhone source is not available when [USB MTP] is set to [ON] in the SYSTEM settings.)

CD

  1. Insert a disc into the disc loading slot with the label side up.
    To eject a disc, stop playback first then press .

USB/iPhone

MTP connection
A device installed with Android OS 4.0 or most of later versions can be connected to the unit via MTP, using the cable supplied with the device. However, depending on the connected device, OS version or the numbers of the files in the device, audio files/songs may not be able to be played back via MTP.

NOTE
If you use an MTP connection, [USB MTP] needs to be set to [ON] in the SYSTEM settings.

AUX

  1. Press SRC/OFF to select [AUX IN] as the source.

Bluetooth connection

Up to two Bluetooth telephones can be connected simultaneously.

Bluetooth telephone

Basic operations

Purpose Operation
Answer an incoming call Press any button when a call is received.
End a call Press .
Reject an incoming call Press and hold when a call is received.

Activating voice recognition mode

  1. Press and hold and then talk into the microphone to input voice commands.

To exit the voice recognition mode, press BAND/.

Making a connection with Pioneer Smart Sync

Pioneer Smart Sync is the application that intelligently brings your maps, messages, and music together in the vehicle.

www.apple.com
play.google.com


Do not attempt to operate the application while driving. Make sure to pull off the road and park your vehicle in a safe location before attempting to use the controls on the application.

  1. Turn the M.C. dial to select [APP CONTROL], then press to confirm.
  2. Turn the M.C. dial to select one of the below.
  3. Turn the M.C. dial to select [AUTO APP CONN], then press to confirm.
  4. Turn the M.C. dial to select [ON], then press to confirm.

NOTE
Regardless of whether the [AUTO APP CONN] setting is set to [ON] or [OFF], you can also perform the following to start Pioneer Smart Sync.

  • For devices other than the USB-connected Android device, press SRC/OFF to select any source and press and hold the M.C. dial.

Listening to Pandora®

(Not available when [USB MTP] is set to [ON] in the SYSTEM settings.)
Update the firmware of the Pandora application to the latest version before use.
Before you start, connect this unit with the mobile device via USB (iPhone only) or Bluetooth.

  1. Turn the M.C. dial to select [APP CONTROL], then press to confirm.
  2. Turn the M.C. dial to select one of the below.
  3. Press SRC/OFF to select [PANDORA].

Listening to Spotify®

(Not available when [USB MTP] is set to [ON] in the SYSTEM settings.)
Update the firmware of the Spotify application to the latest version before use.
Before you start, connect this unit with the mobile device via USB (iPhone only) or Bluetooth.

  1. Turn the M.C. dial to select [APP CONTROL], then press to confirm.
  2. Turn the M.C. dial to select one of the below.
  3. Press SRC/OFF to select [SPOTIFY].


(Serial number)
The serial number is located on the bottom of this unit. For your own security and Guide de démarrage rapide convenience, be sure to record this number on the enclosed warranty card.

Documents / Resources

References

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Table of Contents