Panasonic RP-BTS55 - Digital Wireless Stereo Earphones Manual

Please read these instructions carefully before using this product, and save this manual for future use.

Accessories

Please check and identify the supplied accessories.

1 x USB charging cord

1 x Carrying case

1 x Earpieces set (L, S)

Use only the supplied USB charging cord when connecting to a computer.

Safety precautions

Unit

To reduce the risk of fire, electric shock or product damage, Do not let water or other liquids drip or splash inside the unit. Do not expose accessories (USB charging cord) to rain, moisture, dripping or splashing. Do not place objects filled with liquids, such as vases, on accessories. Use the recommended accessories. Do not remove covers. Do not repair this unit by yourself. Refer servicing to qualified service personnel.

Earpieces

Allergies

Precautions for listening with the Earphones

This unit may receive radio interference caused by mobile telephones during use. If such interference occurs, please increase separation between this unit and the mobile telephone.

This unit is intended for use in moderate and tropical climates.

Maintenance

Clean this unit with a dry and soft cloth.

Specifications

General

Power supply	DC 5 V, 500 mA (Internal battery: 3.7 V (Li-polymer 90 mAh))
Operating time*1 (SBC mode)	Approx. 6 hours
Charging time*2 (25 oC)	Approx. 1.5 hours
Charging temperature range	10 oC to 35 oC
Operating temperature range	0 oC to 40 oC
Operating humidity range	35%RH to 80%RH (no condensation)
Mass	Approx. 22 g

Water resistant

Water resistant

IPX5 equivalent

Bluetooth^® section

Frequency band	2402 MHz to 2480 MHz
Supported profiles	A2DP, AVRCP, HSP, HFP
Supported codec	SBC, AAC

*1 It may be shorter depending on the operating conditions.

*2 Time taken to recharge from empty to full.

Troubleshooting

Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the remedies indicated do not solve the problem, consult your dealer for instructions.

The unit does not respond.

Cannot charge the unit.

LED does not light during charging. / Charging takes longer.

• Is the USB charging cord (supplied) connected firmly to the USB terminal of the computer? (→ )

The power does not turn on.

• Is the unit being charged? The power cannot be turned ON during charging. (→ )

The device cannot be connected.

• Delete the pairing information for this unit from the Bluetooth^®device, then pair them again. (→ )

No sound.

• Make sure that the unit and the Bluetooth^® device are connected correctly. (→ )
• Check if music is playing on the Bluetooth^® device.
• Pair and connect the Bluetooth^® device and the unit again. (→ )
• Check if the Bluetooth^® compatible device supports "A2DP" profile. For details on profiles, see "Listening to music" (→ ). Also refer to the operating manual for the Bluetooth^® compatible device.

Low volume.

• Increase the volume of the unit. (→ )
• Increase the volume on the Bluetooth^® device.

Sound from the device is cut off. / Sound quality is bad.

• A communication problem may arise if the battery is not fully charged. Charge the unit. (→ )

You cannot hear the other person.

• Make sure that the unit and the Bluetooth^® enabled phone are turned on.
• Check if the unit and the Bluetooth^® enabled phone are connected. (→ )
• Check the audio settings of the Bluetooth^® enabled phone. Switch the calling device to the unit if it is set to the Bluetooth^® enabled phone. (→ )
• If the volume of the other person's voice is too low, increase the volume of both the unit and the Bluetooth^® enabled phone.

Cannot make a phone call.

• Check if the Bluetooth^® compatible device supports "HSP" or "HFP" profile. For details on profiles, see "Listening to music" and "Making a phone call" in "Operating Instructions (PDF format)". Also refer to the operating manual for the Bluetooth^® enabled phone.

Part names

1. Blue edge LEDs*¹
2. LED indicator light*²
3. [] button

*1 On: Connect the Bluetooth^® device and the unit. (→ below, ) Press [+] and [–] simultaneously. When the blue edge LEDs are turned on, the LED indicator light will be turned off.
Off: Press and hold [+] and [–] simultaneously for approximately 2 seconds.

*2 Hereafter referred to as "LED"

Charging

The rechargeable battery (installed in the unit) is not charged initially. Charge the battery before using the unit.

Connect this unit to a computer () using the USB charging cord (supplied) ().

• The LED () lights in red when charging is in progress. When charging is completed, the LED will go out.

Turning the power on/off

Press and hold [] () of this unit for approx. 3 seconds until the LED (blue) () blinks.

To turn the power off

Press and hold [] for approximately 3 seconds. A beep will sound and the power will be turned off.

• If the unit is not connected to a Bluetooth^® device, the unit will beep and turn off automatically approximately 5 minutes after you have stopped using it. (Auto power off)

Connecting a Bluetooth^® device

Bluetooth^® pairing

1. In the power-off state, press and hold [] of this unit until the LED blinks in blue and red alternately.
2. Select "RP-BTS55" () from the Bluetooth^® device's menu.

Connecting a paired Bluetooth^® device

1. Turn on this unit.
2. Perform steps 2 of "Bluetooth^® pairing". (→ above)

How to wear the earphones

Using the earphones

Connect the Bluetooth^® device and the unit.

Listening to music

Select and play the music on the Bluetooth^® device.

Remote controlling (Available only if your Bluetooth^® device supports "AVRCP")

(Operation example)

Play / Pause: Press [].

Increase the volume: Press [+].

Decrease the volume: Press [–].

Forward to the start of next track: Press and hold [+] for approximately 2 seconds.

Return to the start of current track: Press and hold [–] for approximately 2 seconds.

Making a phone call

1. Press [] on the unit and answer the incoming call.
2. Start talking.
3. Press [] to end the phone call.
   • (HFP only) Reject a call / Change the call device: Press [] twice quickly.
   • You can have the Bluetooth^® enabled phone make phone calls by using the microphone of the unit and an app of the Bluetooth^® enabled phone. (→ below, "Activating voice functions")

Activating voice functions

Press [] twice quickly.

Restoring to the factory settings

1. While the unit is turned off, press and hold [] for at least 5 seconds until the LED starts blinking alternately in blue and red.
2. While the LED is blinking alternately in blue and red, press and hold [+] and [–] at the same time for at least 5 seconds.

To remove the battery when disposing of this unit

The following instructions are not intended for repairing purposes but for the disposal of this unit. This unit is not restorable once disassembled.

• When disposing of this unit, take out the battery installed in this unit and recycle it.

As the rechargeable battery is specifically for this product, do not use it for any other device.

Do not place the removed battery, and other items within reach of infants.

Accidental swallowing of such an item may have an adverse effect on the body.

In the event of fluid leaking from the battery, take the following measure, and do not touch the fluid with bare hands.

Fluid entering into an eye may cause loss of eyesight.

Fluid getting on your body or clothes may cause inflammation of the skin or injury.

A lithium-ion polymer rechargeable battery is built in to the left earphone. Please discard according to local regulations. When disposing this product, disassemble properly by following the procedure, and remove the internal rechargeable battery.

1. Hold the top of the left earphone (L), and put a straight-slot screwdriver (commercially available) under the upper cover .
2. Use the screwdriver for leverage, and push the upper cover upward.
3. Hold the battery , and remove it.
4. Pull off the battery and separate it from the left earphone by cutting off the wires, one by one, with scissors.

• Close the charging terminal cover securely.
• Do not touch the charging terminal with wet hand.

The Bluetooth^® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Panasonic Corporation is under license.

Other trademarks and trade names are those of their respective owners.

QR Code is a registered trademark of DENSO WAVE INCORPORATED.

Other system names and product names appearing in this document are in general the registered trademarks or trademarks of the respective developer companies.

Note that the ^TM mark and ^® mark do not appear in this document.

Panasonic Warranty

For Australia
Subject to the conditions of this warranty Panasonic or its Authorised Service Centre will perform necessary service on the product, without charge for parts or labour, if in the opinion of Panasonic the product is found to have a manufacturing defect within one (1) year or (12 months) (the "warranty period") from the date of purchase appearing on your purchase receipt..

Panasonic Authorised Service Centres are located in major metropolitan areas and most regional centres of Australia, however, coverage will vary dependent on product. For advice on exact Authorised Service Centre locations for your product, please telephone our Customer Care Centre on 132600 or visit our website and use the Service Centre Locator.

THIS WARRANTY CARD AND THE PURCHASE DOCKET (OR SIMILAR PROOF OF PURCHASE) SHOULD BE RETAINED BY THE CUSTOMER AT ALL TIMES

If you require assistance regarding warranty conditions or any other enquiries, please visit the Panasonic Australia website www.panasonic.com.au or contact by phone on 132 600
If phoning in, please ensure you have your operating instructions available.

Panasonic Australia Pty. Limited
ACN 001 592 187 | ABN 83 001 592 187
1 Innovation Road, Macquarie Park NSW 2113
www.panasonic.com.au

For the United Kingdom and Ireland customers
Sales and Support Information

Customer Communications Centre

• For further support on your product, please visit our website: www.panasonic.co.uk

Direct Sales at Panasonic UK

• Or go on line through our Internet Accessory ordering application at www.pas-europe.com.

For Thailand only
This telecommunication equipment conforms to NTC/NBTC technical requirement.