Quick Links
4-Component Universal Remote
Congratulations on your purchase of this four-
component universal remote. Your universal remote
controls up to four electronic components and makes
juggling remote controls a thing of the past. You can
program your RCA brand universal remote to operate
most models of infrared, remote-controlled components
manufactured after 1990. (See the enclosed Code Lists
for a complete list of brands.) And, not only is your
remote easy to program, it's easy to operate, too. We've
specially designed this remote with big buttons to
give you total control...at the touch of your fingertips.
Tip: The four-component universal remote is already programmed
to operate most RCA, GE and PROSCAN branded TVs, DVD
players and satellite receivers. Just press the corresponding
VCR
key—
for a VCR player;
SAT·CBL
a television;
Component
Keys (TV,
VCR, DVD,
SAT·CBL)
Dedicated
MENU Key
for DVD
disc menus,
satellite
receivers
and some
TVs.
Transport
Keys— REVERSE,
PLAY, FORWARD,
RECORD, STOP
and PAUSE Keys
Actual model may vary from picture shown
RCR451
Universal Remote Control
Owner's Manual
Manual del Propietario (parte posterior)
DVD
for a DVD player;
for a satellite receiver or a cable box.
LED
Indicator
Light
INPUT
Key— On
some
remotes,
this is
called the
TV/VCR key.
It toggles
through all
the video
sources
connected
to your TV.
CH and
VOL keys
have dual
functions.
They act as
navigation
keys (up,
down,
right, left
arrow keys)
in menu
systems.
Battery Installation and Information
Your universal remote requires two AAA Alkaline
batteries (batteries may or may not be included,
depending on model). To install the batteries:
Note: Reprogramming may be required after batteries are
replaced.
Battery Precautions:
•
Do not mix old and new batteries.
TV
for
•
Do not mix alkaline, standard (carbon-zinc) or
rechargeable (nickel-cadmium) batteries.
•
Always remove old, weak or worn-out batteries promptly
and recycle or dispose of them in accordance with Local
and National Regulations.
Battery Saver
Your universal remote control saves battery power
by automatically turning off if any key is pressed for
more than 60 seconds. This saves your batteries should
your remote get stuck in a place where the keys remain
depressed, such as between sofa cushions.
Programming the Remote
Your universal remote can operate a variety of brands
of components. In order for your universal remote to
control your components, you need to program the
remote with the codes that match the components (See
Code Lists enclosed). These codes enable the remote
to communicate with your components. Each brand
and each component has its own "language," and, by
programming the correct codes into your remote, you
tell the remote to "speak the same language" as your
components.
There are two methods you can use to program your
remote control to operate your components: Direct
Code Entry and Manual Code Search and Entry. Most
components can be programmed in one of these ways.
Try them in the order listed.
In order to control combo TV/VCR or TV/DVD units,
you must program both the TV key and the VCR or
DVD key. Once programmed successfully, the TV key
controls the TV functions on your unit, and the VCR or
DVD key controls the VCR or DVD functions. There is
a specific section in the Code Lists for combo units. The
codes in this section should be tried first, using Direct
Code Entry on the TV and VCR or DVD keys. If this is
unsuccessful, follow the normal programming methods
for both the TV and the VCR or DVD keys.
1. Remove the battery compartment
cover.
2. Insert the batteries, matching the
batteries to the (+) and (-) marks
inside the battery compartment.
3. Press and push the battery cover
back into place.
Related Manuals for RCA CRCU5601
Summary of Contents for RCA CRCU5601
- Page 1 Note: Reprogramming may be required after batteries are Tip: The four-component universal remote is already programmed replaced. to operate most RCA, GE and PROSCAN branded TVs, DVD Battery Precautions: players and satellite receivers. Just press the corresponding •...
- Page 2 Programming Methods 6. To confirm that the component key is programmed with the correct code for maximum Direct Code Entry functionality, test the To program your universal remote to control your component. Attempt to control components using the Direct Code Entry Method, a variety of the component’s functions with the remote.
- Page 3 Using the Remote to Control 6. Press and release the ON·OFF key repeatedly until your Your Components component turns off. Each time you press the ON·OFF Because this remote controls more than one component, key, the LED indicator light you must first “tell” the remote which component you blinks, and the next code in wish to operate.
- Page 4 • You may have pressed an invalid key for the mode the remote is in. authorized to assume for the Company any liability other than expressed herein in • If you’re trying to turn on an RCA, GE or PROSCAN component, press connection with the sale of this product.