Panasonic WV-QCL500-S - Ceiling Mount Bracket Manual

Introduction

Panasonic i-PRO Sensing Solutions Co., Ltd. assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation.

Preface

This product is used to mount the PTZ type camera on the ceiling.
For the latest information about the supported cameras, refer to our support website
(https://security.panasonic.com/training_support/support/info/).

Specifications

Precaution

• Refer installation work to the dealer.
  Installation work requires technique and experience. Failure to observe this may cause fire, electric shock, injury, or damage to the product. Be sure to consult the dealer.
• Install the product securely on a ceiling in accordance with the installation instructions.
  Failure to observe this may cause injury or accidents.
• Do not use this bracket except with suitable cameras.
  Failure to observe this may cause a drop resulting in injury or accidents.
• Do not install this product on a place that is greatly influenced by wind.
  Installation on a place where the wind speed is 60 m/s {approx. 134 mph} or more may cause a fall of the product resulting in injury or accidents.

When using this product, also read the "Precautions" described in the operating instructions for the camera to be attached.

Standard accessories

Operating Instructions (this document): 1 pc.

Other items that are needed (not included)

M8 screw: 4 pcs.
M8 flat washer / spring washer: 4 pcs. for each

• This value indicates the minimum pull-out strength required value per screw. For information about the minimum pull-out strength, refer to our support website .
• Select screws according to the material of the location that the camera will be mounted to.
  In this case, wood screws and nails should not be used.

Precautions for installation

• In order to prevent injury, the product must be securely mounted to the ceiling according to the Installation Guide of this bracket.
• Mounting method for this product
  This product is designed to be used as a pendant mount camera. If the product is mounted on a desktop or at a slant, the camera may not work correctly and its lifetime may be shortened.
• Make sure to remove this product if it will no longer be used.

Installation

These instructions use the PTZ type camera (WV-X6531N) to describe installation. Refer to the Installation Guide for each camera for detailed installation information and procedures.

1. Where necessary, remove the cable case and insert an SD memory card.

• When the only necessary connection to camera is an Ethernet cable
  → Do not remove the cable case.
• When using 24 V AC, EXT I/O device, or audio input / output device
  → Remove the cable case.

NOTE

2. Remove the cover from the base of this product.
   

♦ Step 2

Attach the cover of this product to the top of the camera.

Recommended tightening torque: 2.45 N·m {1.81 lbf·ft}

NOTE

♦ Step 3

Get the ceiling ready and attach the base of this product to the ceiling.

Fixing screws: M8 screws (flat washer / spring washer)

Minimum pullout strength: 1539 N {346 lbf} (per 1 pc.)

1. Make screw holes or anchor holes in the ceiling, and also wiring holes if necessary.
   
   A: 71.8 mm × 71.8 mm {2-3/16 inches × 2-3/16 inches}
   B: 120.5 mm × 120.5 mm {4-3/4 inches × 4-3/4 inches}

<When wiring through the ceiling>

• When using the conduit on the ceiling for wiring, remove the cap for the female thread for the conduit by using a hexagon wrench (ISO 2936, width across flats S=5 mm {3/16 inches}).
  The female thread for conduit is compliant with ANSI NPSM (parallel pipe threads) 3/4 or ISO 228-1 (parallel pipe threads) G3/4.

♦ Step 4

Hang the camera from the base of this product with the installed auxiliary wire and connect the cables.

NOTE

♦ Step 5

Put the cover of this product which has been attached to the top of the camera so the fitting holes (2 places) fit over the positioning pins on the base that has been fixed to the ceiling, the turn clockwise approximately 10° to temporarily fix in place.

NOTE

♦ Step 6

Tighten the cover fixing screws (4 places) alternating diagonally with a 4 mm {5/32 inches} hexagon wrench (locally procured) to fix the cover attached to the camera to this product. ( to )

Recommended tightening torque: 2.45 N·m {1.81 lbf·ft}

♦ Step 7

Attach the safety wire of the camera to the wire hook section on the base of this product.

Refer to the Operating Instructions for the camera for information about further adjustments (connecting power to the camera, adjusting the angular field of view).

For U.S. and Canada:
Panasonic i-PRO Sensing Solutions Corporation of America
800 Gessner Rd, Suite 700 Houston, TX 77024
https://www.security.us.panasonic.com/

Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada
1-877-495-0580
https://www.panasonic.com/ca/

For Europe and other countries:
Panasonic Corporation
http://www.panasonic.com

Panasonic i-PRO Sensing Solutions Co., Ltd.
Fukuoka, Japan

Authorised Representative in EU:
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, Germany

© Panasonic i-PRO Sensing Solutions Co., Ltd. 2020