Philips Universal Remote SRP3011 Manual

Your universal remote

Introduction

With the universal remote, you can use it to operate your device.

Overview of the universal remote

1. INPUT: select available source inputs (antenna, cable, etc.).
   : power on or off.
   : LED indicator
2. Digit buttons
   I/II: select the audio channel.
   -/--: select between one and two-figure channel numbers.
3. ▲/▼/◄/►: scroll the menu up/down/ left/right.
   OK: confirm your selection.
4. BACK: go back one menu level.
   : mute
   CH+/-: go to the next/previous channel.
   VOL /: adjust the volume.
   : menu on or off.
5. ///: teletext off/teletext mix/ teletext on/teletext hold
   Red/Green/Yellow/Blue: context sensitivity buttons

Get started

Insert batteries (not included)

NOTE::
When you replace the batteries, all user settings will be retained in the memory of the universal remote for 5 minutes.

Set up the universal remote

You must first set up the universal remote before operating your device.

Manual registration

1. Switch on your device.
   
   
2. Press and hold "1" and "6" at the same time for 5 seconds until the blue LED is on.
   
   
3. Look up the 5-digit code for your brand in the code list. Codes are listed by the device type and brand name. The most popular code is listed first.
   
   
4. Enter the first 5-digit code using the digit buttons.
   
   
5. If the light is off, a valid code is saved. Otherwise, the light will flash once, and then remains on for code re-entry.
   
   

NOTE:

Auto registration

1. Switch on your device.
   
   
2. Press and hold "1" and "6" at the same time for 5 seconds until the blue LED is on.
   
   
3. Point at your device with the universal remote. Then press and release to start searching the code for your brand. A different infrared signal is sent every 2 seconds as the universal remote searches, indicated by a blue flash.
   
   
4. When the device is off, immediately press and release OK to save the code. The blue LED indicator will turn off.
   
   

NOTE:

• Auto registration can be reversed, by pressing and releasing once more during the auto registration process. This is helpful if you missed out the chance to press OK within 2 seconds. Make sure that the device is first powered on again.

Notice

Disposal of your old product and battery

Your product is designed and manufactured with high quality materials and components, which can be recycled and reused.

This symbol on a product means that the product is covered by European Directive 2012/19/EU.

This symbol means that the product contains batteries covered by European Directive 2013/56/EU which cannot be disposed of with normal household waste. Inform yourself about the local separate collection system for electrical and electronic products and batteries. Follow local rules and never dispose of the product and batteries with normal household waste. Correct disposal of old products and batteries helps prevent negative consequences for the environment and human health.

Removing the disposable batteries
To remove the disposable batteries, see section 'Insert batteries'.

When this logo is attached to a product, it means a financial contribution has been paid to the associated national recovery and recycling system.

Environmental information
All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.) Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment.

Service and support

Frequently asked questions

My universal remote does not work at all.

If several device codes are listed under the brand of my device, how can I select the correct device code?
To seek the correct device code, test the codes one by one. The codes are sorted by popularity, and the most popular code is listed first.

My device responds only to some of the commands.
You have set a code for which only some commands work properly but some do not. Try other codes until most keys work properly.

Need help?

We advise you to first read this user manual carefully. It helps you set up and use the universal remote.

If, however, you require extra information or have additional questions about setup, usage, warranty, etc of the SRP3011, you can always contact us.

When calling our helpline, make sure to have the SRP3011 at hand when you call, so that our operators can help you determine whether SRP3011 is working properly.

You will find our contact details at the end of this user manual.

For online support, visit www.philips.com/support

Documents / Resources

References

• Support location selector

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.