Quick Links
EGNL Series Vandal Resistant Emergency Light
AC, AC/DC and Self-powered
Disconnect Power before Installation and Maintenance.
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always
be followed including the following:
READ AND FOLLOW ALL SAFETY
INSTRUCTIONS
1. All servicing should be performed by qualified service personnel.
2. Disconnect power at fuse or circuit breaker before installing or servicing.
3. All electrical connections must be in accordance with local codes,
ordinances and the National Electric code.
4. All unused wires must be capped to prevent shorting.
5. Do not use outdoors.
6. Do not let power supply cords touch hot surfaces.
7. Do not mount near gas or electric heaters.
8. Equipment should be mounted in locations and at heights where it will not
readily be subjected to tampering by unauthorized personnel.
9. The use of accessory equipment not recommended by the manufacturer
may cause an unsafe condition.
10. Do not use this equipment for other than intended use.
11. Use caution when handling batteries (self-powered only).
12. Allow battery to charge for 24 hours before first use (self-powered only).
SAVE THESE INSTRUCTIONS
Installation Instructions
IMPORTANT:
Maximum mounting height: 22 feet from floor.
1. Turn off AC power.
2. Feed AC unswitched circuit of rated voltage into junction box and leave 6"
of wire length.
3. Using a flat head screwdriver, insert the blade into the slots and tilt to
release the latch and open the front cover (see figure 1).
4. Push in the locking clips located on each side of the reflector and remove
the reflector assembly (see figure 1).
Wall and Ceiling Mount
1. Remove the appropriate knockouts in the back plate.
2. Feed AC wires through the center hole into the back plate.
3. Mount and secure the back plate to the junction box. Ensure the gasket is
compressed tightly to the surface.
4. Make the proper connections according to model configuration:
For self-powered see figure 3.
For AC, AC/DC see figure 4.
5. Attach safety cable from housing to reflector assembly.
6. Connect battery connector to PCBA.
7. Reattach reflector assembly. Push in the locking clips located on each side
of the reflector and snap in reflector assembly (see figure 1).
8. Adjust LED strips as required (see figure 6).
9. Snap in the lens.
Note: for units with auto-test option, ensure button on lens aligns with
test switch on reflector.
Tel: (888) 552-6467
© 2020 ABB. All rights reserved.
WARNING:
Risk of Shock.
Fax: (800) 316-4515
EGNL Series Vandal Resistant Emergency Light
Slot location
to open front cover
Reflector locking clip location
Figure 1
Gasket
Back plate
Figure 2
Wiring diagram for self-powered models
With wall switch
Connect the black wire to 120/347Vac, white wire to the neutral.
Connect the red wire to one contact of the wall switch and conect the
other contact to the black wire as shown below.
Test
switch
LED
indicator
PCBA
LED 2
LED 1
Wall switch
Red
White (Neutral)
Black (120 to 347VAC)
Without wall switch
Connect the black and red wires to hot lead, white wire to the neutral as
shown below.
Test
switch
LED
indicator
PCBA
LED 2
LED 1
Red
White (Neutral)
Black (120 to 347VAC)
Figure 3
Use Flexible Conduit Only
Wire nuts
Reflector
Battery
Battery
06/20 750.2103 Rev. A
1/2
Related Manuals for ABB EGNL Series
Summary of Contents for ABB EGNL Series
- Page 1 EGNL Series Vandal Resistant Emergency Light EGNL Series Vandal Resistant Emergency Light Use Flexible Conduit Only AC, AC/DC and Self-powered WARNING: Risk of Shock. Disconnect Power before Installation and Maintenance. IMPORTANT SAFEGUARDS Slot location to open front cover When using electrical equipment, basic safety precautions should always...
- Page 2 EGNL Series Vandal Resistant Emergency Light T-bar installation (see figure 5) Wiring diagram for AC / DC models 1. Bend the 4 tabs on the mounting frame 90 degrees outward to hang onto With wall switch the t-bar. Connect the black wire to 120/347Vac, white wire to the neutral.