Honeywell FocusPRO 5000 Series Manual
- Brochure (1 page) ,
- Operating instructions manual (28 pages) ,
- Quick manual (2 pages)
Thermostat controls
- Battery holder
- Temperature buttons
Press to set preferred temperature. - Function buttons
Press to select the functuion displayed just above each button. (Functions change depending on the task.) - Digital display
Display screen
- Low battery warning
- Current inside temperature
- Press the FAN button to select:
Auto: Fan runs only when heating or cooling system is on.
On: Fan runs continuously. - Function buttons
Press the button beneath each function to view or change settings (functions change depending on the task) - Auxiliary heat (Only for heat pumps with auxiliary heat)
- Temperature setting
- System Status
Cool On: Cooling system is on.
Heat On: Heating system is on. - Press the SYSTEM button to select:
Heat: Heating system control.
Cool: Cooling system control.
Off: All systems off.
Auto: Thermostat automatically selects heating or cooling depending on the indoor temperature.
Heat On: Heating system is on. Emergency & Auxiliary Heat control. Compressor is locked out. (Select models only.)
Auto changeover (heat/cool)
Auto Changeover is a feature used in climates where both air conditioning and heating are used on the same day. When the system is set to Auto, the thermostat automatically selects heating or cooling depending on the indoor temperature.
Heat and cool settings must be at least 3 degrees apart. The thermostat will automatically adjust settings to maintain this 3-degree separation (called "deadband").
The 3-degree separation between heating and cooling set temperatures is fixed, and cannot be changed.
NOTE: The Auto system setting may not appear, depending on how your thermostat was installed
Built-in compressor protection
Damage can occur if the compressor is restarted too soon after shutdown. This feature forces the compressor to wait for a few minutes before restarting.
During the wait time, the display will flash the message Cool On (or Heat On if you have a heat pump). When the safe wait time has elapsed, the message stops flashing and the compressor turns on.
Message flashes until safe restart time has elapsed.
Battery replacement
Batteries are optional (for backup power) if your thermostat was wired to run on AC power when installed.
Install fresh batteries when the REPLACE BATTERY warning begins flashing. The warning flashes about two months before the batteries are depleted.
Replace batteries once a year, or before leaving home for more than a month. All settings are permanently stored in memory, and do not require battery power.
Press and pull to remove.
Insert fresh alkaline batteries, then reinstall battery holder.
TH5110D:
AAA alkaline batteries.
TH5320U/TH5220D:
AA alkaline batteries.
Customer assistance
For assistance with this product, please visit yourhome.honeywell.com.
Or call Honeywell Customer Care tollfree at 1-800-468-1502.
Press and pull to remove.
Turn thermostat over to find model number and date code.
Equipment damage hazard
To prevent possible compressor damage, do not operate cooling system when outdoor temperature is below 50°F (10°C).
Accessories/replacement parts
To order, please call Honeywell Customer Care toll-free at 1-800-468-1502.
TH5110D
Battery holder...........................Part No. 50000951-001
Cover plate assembly*..............Part No. 50001137-001
Cover plate assembly*..............Part No. 50002883-001
TH5320U/TH5220D
Battery holder...........................Part No. 50007072-001
Cover plate assembly*..............Part No. 50002883-001
*Use to cover marks left by old thermostats.
Troubleshooting
If you have difficulty with your thermostat, please try the following suggestions. Most problems can be corrected quickly and easily.
Display is blank
- Check circuit breaker and reset if necessary.
- Make sure power switch at heating & cooling system is on.
- Make sure furnace door is closed securely.
- Make sure fresh AA or AAA alkaline batteries (depending on model) are correctly installed.
Heating or cooling system does not respond
- Press SYSTEM button to set system Heat. Make sure the temperature is set higher than the Inside temperature.
- Press SYSTEM button to set system to Cool. Make sure the temperature is set lower than the Inside temperature.
- Check circuit breaker and reset if necessary.
- Make sure power switch at heating & cooling system is on.
- Make sure furnace door is closed securely.
- Wait 5 minutes for the system to respond.
Temperature settings do not change
Make sure heating and cooling temperatures are set to acceptable ranges:
"Cool On" or "Heat On" is flashing
-
Compressor protection feature is engaged. Wait 5 minutes for the system to restart safely, without damage to the compressor.
5-year limited warranty
Honeywell warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and service, for a period of five (5) years from the date of purchase by the consumer. If at any time during the warranty period the product is determined to be defective or malfunctions, Honeywell shall repair or replace it (at Honeywell's option).
If the product is defective,
(i) return it, with a bill of sale or other dated proof of purchase, to the place from which you purchased it; or
(ii) call Honeywell Customer Care at 1-800-468-1502. Customer Care will make the determination whether the product should be returned to the following address: Honeywell Return Goods, Dock 4 MN10-3860, 1885 Douglas Dr. N., Golden Valley, MN 55422, or whether a replacement product can be sent to you.
This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by Honeywell that the defect or malfunction was caused by damage which occurred while the product was in the possession of a consumer.
Honeywell's sole responsibility shall be to repair or replace the product within the terms stated above. HONEYWELL SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you.
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEYWELL MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE FIVE-YEAR DURATION OF THIS WARRANTY.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from state to state.
If you have any questions concerning this warranty, please write Honeywell Customer Relations, 1985 Douglas Dr, Golden Valley, MN 55422 or call 1-800-468-1502. In Canada, write Retail Products ON15-02H, Honeywell Limited/Honeywell Limitée, 35 Dynamic Drive, Toronto, Ontario M1V4Z9.
Automation and Control Solutions
Honeywell International Inc.
1985 Douglas Drive North
Golden Valley, MN 55422
yourhome.honeywell.com
® U.S. Registered Trademark.
© 2013 Honeywell International Inc.
69-1923EFS—03 M.S. Rev. 07-13
Printed in U.S.A.
VideosHoneywell Focus Pro 5000 Review Video
Documents / Resources
References
Download manual
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the FocusPRO 5000 that isn't answered in the manual? Leave your question here.