Fujitsu 9378782051 Installation Instruction Sheet

Quick Links

Receiver Kit
INSTALLATION INSTRUCTION SHEET
(PART No. 9378782051)
For authorized service personnel only.
This mark indicates procedures which, if improperly performed, might lead to the death or serious injury of the
WARNING
user.
① For the air conditioner to operate satisfactorily, install it as outlined in this installation instruction sheet.
② Installation work must be performed in accordance with national wiring standards by authorized personnel only.
③ Do not turn on the power until all installation work is complete.
• Let the customer keep this installation instruction sheet because it is needed when the air conditioner or receiver kit is serviced or
moved.
This mark indicates procedures which, if improperly performed, might possibly result in personal harm to the
CAUTION
user, or damage to property.
① Do not wire the receiver kit wire together with or parallel to the connection cables, transmission cords, remote controller cords, bus
wire and power supply cords of the indoor and outdoor units. It may cause erroneous operation.
② Do not install the receiver kit wire near a source of electromagnetic waves.
1
The following installation parts are supplied. Use them as required.
Name and Shape
Q'ty
Application
Receiver unit
For receiving the signal
from the remote controller
1
Strap
Prevent receiver kit from
falling down
1
Screw (ø3 × 12)
For installing remote
controller holder to wall
2
② Insert the wire from the RECEIVER UNIT into the wiring hole as shown in the figure below and pull it into the Decoration
panel.
Wiring hole
Wire from RECEIVER UNIT
③ Hang the STRAP on the hook of the Decoration panel.
After that, mount the RECEIVER UNIT onto the Decoration panel.
Hook
3. WIRING
① Connect the connector to the board in the CONTROL BOX.
STANDARD PARTS
Name and Shape
Q'ty
Remote controller
Use for air conditioner
operation
1
Battery
For remote controller
2
Remote
Use as remote controller
controller holder
holder
1
RECEIVER UNIT
Decoration Panel
Strap
2
3
1. REMOVING THE CONTROL BOX COVER
① Remove the screws.(2 places)
② Slide the CONTROL BOX COVER in the direction of the arrow.
③ Remove the CONTROL BOX COVER.
Application
CONTROL BOX COVER
CONTROL BOX COVER
2. INSTALLING THE RECEIVER UNIT
① Mount the corner (figure to the drainpipe) of the decoration panel that has the "DISPLAY" mark onto the RECEIVER UNIT.
This corner must be mounted onto the RECEIVER UNIT.
② Bundle the FLAP wires (2) to the RECEIVER UNIT wire as shown in the figure below.
Wire for FLAP
Wire from RECEIVER UNIT
4. INSTALLING THE CONTROL BOX COVER
① Secure the CONTROL BOX COVER in the procedure that is reverse to the steps in "1. REMOVING THE CONTROL BOX
COVER".
4
① Turn on the breaker.
② Make sure that the operation lamp and timer lamp are slowly flashing alternately.
• If the auto restart function has been set, the air conditioner will operate with the settings immediately before the power sup-
ply was turned off.
• If an error has occurred, the lamps on the receiver unit will flash quickly to indicate the error code.
5
1. LOAD BATTERIES (R03/LR03 × 2)
① Press and slide the battery compartment lid on the reverse side to open it.
Slide in the direction of the arrow while pressing the
② Insert batteries.
Be sure to align the battery polarities (
③ Close the battery compartment lid.
① Take care to prevent infants from accidentally swallowing batteries.
② When not using the remote controller for an extended period, remove the batteries to avoid possible leakage and damage to
the unit.
③ If leaking battery fluid comes in contact with your skin, eyes, or mouth, immediately wash with copious amounts of water, and
consult your physician.
④ Dead batteries should be removed immediately and disposed of properly, either in a battery collection receptacle or to the
appropriate authority.
⑤ Do not attempt to recharge dry batteries.
NOTES
• Never mix new and used batteries, or batteries of different types.
• Batteries should last about one year under normal use. If the remote controller's operating range becomes appreciably
reduced, replace the batteries and press the RESET button with the tip of a ballpoint pen or other small object.
FUNCTIONS
ECONOMY LAMP
(green)
TIMER LAMP
(orange)
OPERATION LAMP
(green)
MANUAL AUTO
SIGNAL RECEIVER
INSTALLING THE RECEIVER KIT
CAUTION
Wire for FLAP
TURNING ON THE BREAKER
REMOTE CONTROLLER SETTING
mark.
) correctly.
CAUTION
loading

Summary of Contents for Fujitsu 9378782051

  • Page 1 Receiver Kit FUNCTIONS INSTALLATION INSTRUCTION SHEET (PART No. 9378782051) ECONOMY LAMP (green) For authorized service personnel only. TIMER LAMP (orange) This mark indicates procedures which, if improperly performed, might lead to the death or serious injury of the WARNING OPERATION LAMP user. (green) ① For the air conditioner to operate satisfactorily, install it as outlined in this installation instruction sheet. MANUAL AUTO ② Installation work must be performed in accordance with national wiring standards by authorized personnel only. ③ Do not turn on the power until all installation work is complete. SIGNAL RECEIVER • Let the customer keep this installation instruction sheet because it is needed when the air conditioner or receiver kit is serviced or moved. This mark indicates procedures which, if improperly performed, might possibly result in personal harm to the INSTALLING THE RECEIVER KIT CAUTION user, or damage to property.
  • Page 2 Match the code on the display to the air ◊ : 0.1s ON / 0.1s OFF [Simultaneous Multi] conditioner signal code. Power supply interruption ( ) : Number of fl ashing ●(3) ●(1) ◊ ④ Press the MODE button again to return to error the clock display. The signal code will be changed. PART No. 9378782051...