Table of Contents
Quick Links
Doc. No.
78-1231-02
Cisco 7010 and Cisco 7505
Rack-Mount and Cable Management Kits
Installation Instructions
Cisco 7010 Product Numbers: ACC-7010RMK= and ACC-7010CBLM=
Cisco 7505 Product Numbers: ACS/5-RMK= and ACS/5-CBLM=
Customer Order Number: DOC-781231=
This document contains instructions for installing the Cisco 7010 and Cisco 7505 in an equipment
rack using the rack-mount kit, and for installing the cable management brackets on the Cisco 7010
and Cisco 7505.
Note
used.
The rack-mount kit provides hardware for mounting the chassis in most standard 19-inch or
Telco-type equipment racks. The cable management kit provides two brackets for routing and
securing network interface cables at the interface processor end of the chassis.
Both kits are included with their respective chassis, and each kit is available as a spare part.
The sections in this document include the following:
•
•
•
•
•
Copyright © 1995
Cisco Systems, Inc.
All rights reserved.
When referring to both the Cisco 7505 and Cisco 7010 chassis, the term the chassis will be
Product Overview, page 2
Prerequisites, page 3
Rack-Mounting the Chassis, page 7
Installing the Cable Management Brackets, page 12
Cisco Information Online, page 13
1
Table of Contents
Related Manuals for Cisco Rack-Mount and Cable Mgmt. Cisco 7505/7010
Summary of Contents for Cisco Rack-Mount and Cable Mgmt. Cisco 7505/7010
-
Page 1: Installation Instructions
The sections in this document include the following: • Product Overview, page 2 • Prerequisites, page 3 • Rack-Mounting the Chassis, page 7 • Installing the Cable Management Brackets, page 12 • Cisco Information Online, page 13 Copyright © 1995 Cisco Systems, Inc. All rights reserved. -
Page 2: Product Overview
Product Overview Product Overview The Cisco 7010 is the five-slot model in the Cisco 7000 series product line and the Cisco 7505 is the five-slot model in the Cisco 7500 series. Figure 1 shows the interface processor end of the Cisco 7010 chassis. -
Page 3: Safety Guidelines
The cable management kit includes two brackets and fasteners to secure the brackets to the inner sides of the interface processor end of the chassis. By routing cables through the brackets and away from the interface ports, you can keep cables sorted and organized, provide strain relief for heavy or lengthy cables, and maintain clear access to interface processors and ports in the lower slots. -
Page 4: Tools And Equipment
Prerequisites Lifting Safely Whenever you lift the chassis or any heavy object, follow these guidelines: • A fully configured chassis weighs approximately 70 pounds. Whenever possible, avoid lifting the chassis by yourself. • Ensure that your footing is solid and balance the weight of the object between your feet. •... - Page 5 Equipment Racks Considerations The rack-mounting hardware included with the router is suitable for most 19-inch equipment racks or Telco-type racks. The chassis mounts to two posts or rails in the rack with two mounting ears, which attach to the sides of the chassis. Ideally, you should be able to access both ends of the router without having to remove it from the rack.
- Page 6 Prerequisites • If the rack has a vertical power strip or other obstacle, ensure that there is sufficient clearance to install and remove processor modules. Allow at least 12 inches of clearance to pull the modules straight out of their slots. •...
-
Page 7: Rack-Mounting The Chassis
• Install and use the cable management brackets included with the router to keep cables organized and out of the way. Consider the equipment and cabling that is already installed in the rack. Ensure that cables from other equipment will not impair access to the interface processors, or require you to disconnect cables unnecessarily to perform equipment maintenance or upgrades. - Page 8 Rack-Mounting the Chassis Figure 3 Typical 19-Inch Equipment Rack Posts and Mounting Strips 18.312" hole C to C Mounting strips 17.72" min. If you are installing a new router, mount the chassis in the rack before connecting any interface or power cables.
-
Page 9: Installing The Chassis In The Rack
Figure 4 Installing the Ears on the Chassis While referring to Figure 4, turn the chassis so that the end that will be in the front of the Step 4 rack is facing toward you. For example, Figure 4 shows the correct orientation for the router if the noninterface processor end will face out the front of the rack. - Page 10 Rack-Mounting the Chassis Figure 5 Installing the Chassis in a Four-Post, 19-Inch Rack Warning Install heavier equipment near the bottom of the rack to maintain a low center of gravity. A top-heavy rack could easily tip over if it is not anchored or bolted to the floor, resulting in injury. Figure 6 Installing the Chassis in a Telco Rack 10 Cisco 7010 and Cisco 7505 Rack-Mount and Cable Management Kits Installation Instructions...
- Page 11 To install the chassis in the rack, follow these steps: On the chassis, ensure that all captive screws (on the processor modules and on the access Step 1 cover) are tightened. Make sure that your path to the rack is unobstructed. If the rack is on wheels, ensure that Step 2 the brakes are engaged or that the rack is otherwise immobilized.
-
Page 12: Installing The Cable Management Brackets
Installing the Cable Management Brackets Installing the Cable Management Brackets The cable management brackets attach to the inner sides of the chassis at the interface processor end. (See Figure 7.) For this procedure, the Cisco 7010 and Cisco 7505 chassis are functionally the same. Note Use the brackets to keep network interface cables untangled and orderly, provide strain relief, and prevent cables from hindering access to interface processors in the lower interface processor slots. -
Page 13: Cisco Information Online
UniverCD, WNIC, Workgroup Director, Workgroup Stack, and XCI are trademarks; Access by Cisco and Bringing the power of internetworking to everyone are service marks; and Cisco, Cisco Systems, the Cisco logo, EtherSwitch, and Kalpana are registered trademarks of Cisco Systems, Inc. All other trademarks, service marks, registered trademarks, or registered service marks mentioned in this document are the property of their respective owners. - Page 14 Cisco Information Online 14 Cisco 7010 and Cisco 7505 Rack-Mount and Cable Management Kits Installation Instructions...