GE MDS iNET Series Setup Manual
Hide thumbs Also See for MDS iNET Series:

Quick Links

1.0
INTRODUCTION
This guide provides installation instructions for MDS iNET Series
transceivers
(Figure
1). It covers both MDS iNET-II and iNET
models. For detailed product information, refer to the
Technical Manual, part no. 05-2806A01. It contains important
notices on the safe and effective use of this product and
should be reviewed prior to any operation.
Electronic copies of all GE MDS manuals are available free of
charge at www.gemds.com.
Figure 1. MDS iNET Series Transceiver
2.0
PRODUCT DESCRIPTION
MDS iNET transceivers provide wireless connectivity for local area
networks (LANs) with easily installed hardware. The units come in
two primary models—Access Point (AP) and Remote.
An AP is a wireless "hub" that normally provides connectivity into a
wired Ethernet LAN/WAN. It serves as the network's "master
station" providing synchronization data to all associated Remotes
within the network.
Three types of Remotes are available—the Ethernet Bridge, the
Serial Gateway, and the Dual Gateway which supports both
IP/Ethernet and serial services.
interface abilities for each AP and Remote radio type.
Table 1. Transceiver Models and Interfaces
Model
Type
2
N/A
Access Point
Remote...
Ethernet Bridge
Serial Gateway
Dual Gateway
NOTES
1. Provides PC access to the Menu System on all units.
2. Can be configured as an Access Point or Dual Gateway.
3. An Ethernet Bridge can be configured as a Serial Gateway and
vice versa.
4. Can be upgraded to Dual Gateway with an Authorization Key.
A given transceiver may be configured to operate as an Access
Point or a Remote with certain restrictions. The following rules
apply to unit configuration:
1. A Serial or Ethernet Remote can be changed from one to the
other without an Authorization code.
2. If both the Serial and Ethernet Authorization Codes are entered,
the Remote becomes a Dual Gateway. Each code is associated
with the serial number of a particular radio.
05-2873A01, Rev. F
Invisible
place
holder
Table 1
summarizes the different
1
1
COM2
LAN
COM1
Yes
Yes
Yes
3, 4
Yes
No
No
3, 4
No
Yes
Yes
3
Yes
Yes
Yes
MDS iNET Series Setup Guide
3. A Dual Gateway Remote can be reconfigured as an Access
Point. by entering an Access Point Authorization Code from the
Factory.
4. An Access Point can be reconfigured as a Dual Gateway by
changing the device mode in the management interfaces.
2.0.1
Differences Between iNET-II and iNET
The iNET-II and iNET Transceivers, while similar in many
respects, do have important differences and are not over-the-air
compatible. Key differences are summarized in
Table 2. Transceiver Differences (iNET vs. iNET-II)
Characteristic
iNET-II
Data Rate
512 kbps/1 Mbps
FCC Certification Type DTS
Encryption
AES-128
Channel size
600 kHz
Channel operation
Channels
Firmware
Specific for iNET-II
2.1
SECURITY FEATURES
The transceiver is capable of dealing with many common security
issues.
Table
3 profiles security risks and how the transceiver
provides a solution for minimizing vulnerability. In all cases, the
Security Configuration Menu should be reviewed and set to the
required parameters for your environment. Consult with your
network administrator if you are unsure of the required settings.
Table 3. Cyber Security Highlights
Security Level
Specification
• MDS Cyber Security
• AES-128 encryption (iNET-II only)
Suite, Level 4:
• 802.1Q VLAN
• Includes Level 3 features listed below
• MDS Cyber Security
• RC4-128 encryption (iNET only)
Suite, Level 3:
• Automatic rotating key algorithm
• Authentication: 802.1x, RADIUS, EAP/TLS,
(PKI is a requirement of the TLS), PAP,
CHAP.
• Local Device authentication using MAC
address "white lists" on the AP and Remote
• Management: SSL, SSH, HTTPS
• Failed login lockdown
• 900 MHz operation and proprietary data
framing
3.0
INSTALLATION
3.0.1
General Requirements
There are three main requirements for installing the transceiver:
1. Adequate and stable primary power
2. A good antenna system
3. The correct interface between the transceiver and connected
equipment
Figure
2 shows a typical installation for a Remote site. AP sites are
similar, but typically use an omnidirectional antenna to allow for
communication with widely distributed Remote stations.
MDS iNET Series
Setup Guide
Table
2:
iNET
256/512 kbps
FHSS
RC4-128
316.5 kHz
Zones
Specific for iNET
1
loading

Summary of Contents for GE MDS iNET Series

  • Page 1 The iNET-II and iNET Transceivers, while similar in many should be reviewed prior to any operation. respects, do have important differences and are not over-the-air Electronic copies of all GE MDS manuals are available free of compatible. Key differences are summarized in Table charge at www.gemds.com.
  • Page 2 7..Request-to-Send (RTS) 8..Unused 8..Clear-to-Send (CTS) 8..Unused 9..Unused 9..Unused 10BaseT Supported RS/EIA-232 RS/EIA -232 Figure 5. Port Information (All pinouts as viewed from outside the radio) 7.25˝ (18.4 cm) Figure 3. Transceiver Mounting Dimensions MDS iNET Series Setup Guide 05-2873A01, Rev. F...
  • Page 3 PING command to it through the LAN port. This A unique IP address and subnet are required to access verifies basic LAN connectivity with the host. the Menu System, either through the LAN port, or remotely over-the-air. 05-2873A01, Rev. F MDS iNET Series Setup Guide...
  • Page 4 If a problem 5. View the Wireless Packets Dropped and Received Error rates persists, factory technical assistance is available by contacting GE at the point of maximum RSSI level. They should be the same MDS during business hours (8:30 AM to 6:00 PM Eastern Time).

This manual is also suitable for:

Mds inet-iiMds inet