ARD-FPBEW2-H3 Fingerprint Reader, Multiclass Table of contents | en Table of contents Safety and handling Introduction Components Names and function of parts Cables and connectors How to enroll a fingerprint Installation Fixing the bracket and the product Power supply connection...
When installing more than one device, allow space between the devices. Notice! In case of malfunction, contact Bosch After-Sales Service. Do not attempt to repair the product yourself or free after-sales service will not be provided. Old electrical and electronic equipment This product and/or battery must be disposed of separately from household waste.
Page 5
ARD-FPBEW2-H3 Fingerprint Reader, Multiclass Safety and handling | en Notice! Use of the Wiegand interface For data security reasons, the use of the Wiegand interface is not recommended. A secure encrypted data connection is only obtained with the use of the OSDP v2 protocol. The OSDP protocol is used via the RS485 connection.
ARD-FPBEW2-H3 Fingerprint Reader, Multiclass Introduction | en Names and function of parts Item Feature LED lamp Indicates the operational status of the product with the color of the LED lamp. RF card authentication unit Reads RF cards for entering and exiting.
| Introduction ARD-FPBEW2-H3 Fingerprint Reader, Multiclass Cables and connectors * Cut the required wires off the connector plug. Cable Cable name Wiegand cable Ethernet cable Power cable RS485 cable 2022-06 | v01 | Bosch Access Systems GmbH Installation manual...
Page 9
ARD-FPBEW2-H3 Fingerprint Reader, Multiclass Introduction | en Cable Cable name Color WG Tamper NO Gray (White stripe) WG Tamper COM Green (White stripe) WG Tamper NC Orange (White stripe) Not used Blue Brown Not used Green WG D0 Green WG D1...
| Introduction ARD-FPBEW2-H3 Fingerprint Reader, Multiclass How to enroll a fingerprint In order to improve the fingerprint authentication rate, register the fingerprint correctly. The reader can recognize a fingerprint even if the angle and position of a user's fingerprint input change.
Page 11
ARD-FPBEW2-H3 Fingerprint Reader, Multiclass Introduction | en Cautions for enrolling a fingerprint When a fingerprint is recognized, it is compared with the initially registered fingerprint, so the initial fingerprint enroll is the most important. Pay attention to the following matters when enrolling the fingerprint: Place the finger deep enough to contact with the sensor completely.
| Installation ARD-FPBEW2-H3 Fingerprint Reader, Multiclass Installation Fixing the bracket and the product Determine the correct position to install the bracket using the provided drilling template. Fix the bracket firmly using fixing screws through the bracket to the position where the device will be installed.
Page 13
ARD-FPBEW2-H3 Fingerprint Reader, Multiclass Installation | en Installing the device on a concrete wall Drill holes on the wall. Insert the PVC anchors. Fix the anchors with fixing screws. Maintain a minimum separation distance to avoid RF interference (see table below).
| Installation ARD-FPBEW2-H3 Fingerprint Reader, Multiclass Power supply connection 11 - PWR +VDC (Optional) 13 - PWR GND Black (White stripe) 12V DC Warning! When connecting to an AMC2-4R4CF controller, note that the 12V power supply is used. Warning! Do not connect the device to the DC power supply(or adapter) and PoE power supply at the same time.
ARD-FPBEW2-H3 Fingerprint Reader, Multiclass Installation | en Network connection - TCP/IP LAN connection (connecting to a hub) You can connect the product to a hub using a general type CAT-5 cable (or higher). LAN connection (connecting to a PC directly) The ARD-FPBEW2 has an automatic MDI/MDIX function so that it can be connected to a PC directly using a normal straight type CAT-5 cable (or higher), not a cross cable.
| Installation ARD-FPBEW2-H3 Fingerprint Reader, Multiclass Wiegand connection - WG Tamper NO Gray (White stripe) - WG Tamper COM Green (White stripe) - WG Tamper NC Orange (White stripe) - WG D0 Green - WG D1 White - WG GND...
ARD-FPBEW2-H3 Fingerprint Reader, Multiclass UL | en UL 294 requirements The following UL 294 levels apply: – Destructive attack - level 2 – Line security - level 2 – Endurance - level 1 – Standby power- level 1 If the unit is powered by an external power supply, you can use: –...
| FCC ARD-FPBEW2-H3 Fingerprint Reader, Multiclass Compliance information This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.