Honeywell IPCAM-WOC1 Quick Installation Manual

IPCAM-WOC1 HD Wi-Fi Outdoor Video Camera

Quick Installation Guide

IPCAM-WOC1 is a 1080p, full HD Wi-Fi® video camera intended for outdoor use with Honeywell Total Connect® 2.0.

• Camera setup requires a Total Connect® 2.0 account and the new Total Connect 2.0 mobile app. Video Services must be enabled in AlarmNet 360™.

• Camera operation requires minimum available bandwidth of 2.1 Mbps.

Package Contents

A. Sun shield

B. Camera

C. Power cable extension [7' cable]

D. Power adapter with 8' cable

E. Pig-tail power cable

F. Mounting screws and Allen wrench

G. Antenna

Planning Configuration and Installation

See the other side of this sheet for more about mounting at the installation site

• The camera should be situated within 300 feet (91 m) of a power outlet and within the verified range of its WI-FI connection. DO NOT mount the

camera within 1 foot (0.3 m) of any other wireless device. Depending on the specifics of your installation, a range extender may be needed to ensure

adequate signal strength.

• It is strongly recommended that camera configuration be done as close as possible to the Wi-Fi router with which the camera will be linked. After

successful setup, use the app to check signal strength at the installation site before mounting (over for more information on signal strength.)

• The power adapter must be connected to a non-switchable power outlet.

• The included sun shield should be attached to the camera in locations where sun glare may be a problem.

IMPORTANT: You may use only ONE of the included power extension cables. This cable adds 7 feet (2.1 m) to the supplied power adapter for a total of 15

feet (4.5 meters). Alternately, you may use the pig-tail power cable to extend the power adapter cable with up to 300 feet (91 m) of 18 AWG wire, minimum.

Wi-Fi Configuration and Camera Registration

Google Play and the Google Play logo are trademarks of Google Inc.

Download the Total Connect® 2.0 app from the App Store or on Google Play.

(Look for the red Total Connect 2.0 logo.) Note: Significant differences between the

iOS and Android versions of the app are noted in these instructions.

For best results, configure only one camera at a time.

Check these settings when you turn on your mobile device's Wi-Fi and Bluetooth:

• Make sure the Bluetooth isn't connected to another device, such as headphones

• Wi-Fi should be on the same network your camera(s) will use

• Also, make sure the device is not on Silent (ringer and speaker)

a. Verify that the camera's antenna is firmly connected.

b. Turn on your smart device's Bluetooth and

c.

Launch the app and sign in with your Total Connect® 2.0 account.

d. Plug the power supply into an AC outlet, but:.

DON'T CONNECT THE POWER SUPPLY TO THE CAMERA YET! When you do,

refer to the diagram at right

If your account has more than one Location, select the appropriate one using the

dropdown

menu at the top of the screen.

Press CAMERAS at the bottom (iOS) or top (Android) of the screen. (Remember that the

horizontal Navigation Order can be customized in iOS.)

a. At upper right, press ADD CAMERA (iOS) or

b. Select the type of camera you're installing. The names of the camera models may

vary from the illustration at right.

c.

Name the camera and press NEXT.

d. Connect the power supply to the camera. The LED at the top flashes various colors.

Then, WAIT for the camera's LED to flash blue only. This may take a couple of minutes.

e.

Press NEXT on the app.

a. On the Pair Your Camera screen, press Generate QR Code. After a brief wait, the

code appears.

b. Show the QR code on your device to the camera from 3 – 8 inches away.

If you can, keep an eye on your device's screen; when the code is scanned

successfully, a confirmation message will appear over the QR code.

The app will also provide audible confirmation via your mobile device's speaker.

Select your security system's Wi-Fi network and press NEXT.

c. Enter the network password and press NEXT. Final setup begins.

When setup is complete, the LED on the camera changes from steady blue, to purple

and finally to steady green.

The app also displays Setup Successful*. Press DONE or ADD ANOTHER CAMERA.

After setup, go back to the CAMERAS page and check your newly-registered camera.

Touch the preview image to launch a live stream from the camera.

*The app will tell you if you need to repeat the setup process. This involves resetting

the camera, which is described in the app itself.

See the other side of this sheet for more information about the required steps.

BETA

Wi-Fi.

→

(Android)

a. Bluetooth antenna

b. Audio (not used)

c. Reset switch

d. Power