Table of Contents
Quick Links
1. Scope.................................................................................................................................... G2
2. Tools and Parts..................................................................................................................... G2
3. Installation Time.................................................................................................................... G2
4. Procedure ............................................................................................................................. G2
5. Installation Work ................................................................................................................... G3
5.1 Preparation ...................................................................................................................... G3
5.2 Requirement for host systems ......................................................................................... G9
5.2.1 OS, Available memory capacity of Memory and Disk................................................. G9
5.2.2 Requirement for USB ............................................................................................... G10
5.3 Installation of Image Scanner Driver .............................................................................. G11
5.4 Test Scanning ................................................................................................................ G11
5.5 Delevery......................................................................................................................... G11
5.6 Check with Data Sheet for Installation ........................................................................... G12
REVISION Control Table
REV
Date
0
10.03.24
HT-4139 OCR Scanner on-site Installation Manual
Contents
Original
-G1-
Rev0 10.03.24
Changes
Table of Contents
Related Manuals for Hitachi HT-4139
Summary of Contents for Hitachi HT-4139
-
Page 1: Table Of Contents
Rev0 10.03.24 HT-4139 OCR Scanner on-site Installation Manual Contents 1. Scope............................ G2 2. Tools and Parts........................G2 3. Installation Time........................G2 4. Procedure ..........................G2 5. Installation Work ........................G3 5.1 Preparation ........................G3 5.2 Requirement for host systems ..................G9 5.2.1 OS, Available memory capacity of Memory and Disk.......... -
Page 2: Scope
Rev0 10.03.24 1. Scope This manual is applied to the on-site installation of OCR scanner HT-4139. The OCR scanner HT-4139 can be operated by connecting to the PC with the USB cable. 2. Tools and Parts (1) Standard Tools (2) Circuit Tester (3) Ethanol, Gauze 3. -
Page 3: Preparation
Rev0 10.03.24 5. Installation 5.1 Preparation Conduct items shown below. Item Procedure Components Check their names and quantity with the attached component list. Cleaning If the device is contaminated, clean up it with gauze and ethanol. Appearance Ensure there is no scratch, deformation, or discoloration on the device. Power Supply Required Power (Voltage): 400W(AC100V)･200W(AC200V) Frequency: for both 50/60Hz ：The third-class level grounding is preferable. - Page 4 Rev0 10.03.24 Item Procedure (cont.) (cont.) (3) Move the Elevator Arms down as shown in the picture below. Hopper Elevator Arm Elevator Arm Attachment At installation At shipment (4) Remove the Hopper Cover by removing 2 screws. (5) Loosen the Hopper Attaching Screw at the left of the device and attach the Hopper ASSY.
- Page 5 Rev0 10.03.24 (cont.) ITEM Procedure Stacker (1) Open the Top Cover by pushing the Top Latch Button. Attachment (2) Attach the Stacker ASSY-A to the Stacker Bracket. Secure the Stacker with attached 3 flat-head Phillips screws. (3) Attach the Stacker ASSY-R to the Stacker Bracket with the same procedure as shown (4) Close the Top Cover Fixation Screw...
- Page 6 Rev0 10.03.24 (cont.) ITEM Procedure Stacker (1) Secure the Stacker Guide with the Stacker Guide Fixation Screw. Guide Attachment Stacker Guide (cont.) -G6-...
- Page 7 REV0 10.03.24 (cont.) ITEM Procedure Position of (1) By pushing the Top Latch Button, open the Top Cover. Imprinting (2) Pushing the ”PUSH OPEN” label area on the Numbering (Imprinting) Cover and setting of open the Numbering (Imprinting) Cover. ribbon cassette Pedestal of Ribbon Cassette Numbering (Imprinting) Cover...
- Page 8 Rev0 10.02.21 (cont.) ITEM Procedure Cable Connection the power cable and the USB cable. Connection (1) Connect the power cable that is attached to the device to the Inlet connector that is at the side of the device. The other side should be connected to the power outlet whose voltage was measured at No.
-
Page 9: Requirement For Host Systems
REV0 10.03.24 5.2 Confirmation of System requirement for the host 5.2.1 OS, Available memory capacity of Memory and Disk Prior to set up of the Image Scanner Driver, confirm the host systems meet the requirement below. The device installation should be done after setting up the host systems that satisfy the requirement. <... -
Page 10: Requirement For Usb
Rev0 10.03.24 5.2.2 Requirement for USB The USB port and the USB driver should be installed into the host systems with which set up the Image Scanner Driver properly. Check the following items. Check Item Check Result If the USB port dedicated to the OCR scanner is installed? If other boards (SCSI board, LAN board, etc.) are installed? If any conflict of hardware? (IRQ、I/O port address) If the USB driver is installed and work properly? - Page 11 REV0 10.03.24 (3) Windows 7 (1) Open Device Manager by clicking the Start button, clicking Control Panel, clicking Hardware and Sound, and then clicking Device Manager. If you are prompted for an administrator password or confirmation, type the password or provide confirmation. ●Points need to be confirmed Check if the host controller corresponds to USB 2.0 is working properly.
-
Page 12: Installation Of Image Scanner Driver
DON'T connect the USB cable to the PC yet. Install the Image Scanner Driver to the PC. Refer to HT-4139 Image Scanner Driver Installation Guide for instruction. 5.4 Test Scannig Ask customer to test scan from the scanning application if possible. -
Page 13: Test Scanning
REV0 10.03.24 5.6 Check with Confirmation Data Sheet for Installation With the checklist below, ensure all work has been completed. Item Content Check Result Installation Unpacking and checking the device Preparation Components, Appearance, Cleaning Check power supply systems Measurement of Input voltage Hopper Attachment Stacker/Stacker Guide Attachment Position of Imprinting and setting of ribbon cassette...