Husqvarna BV 20 G Operator's Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Power Tool
  5. BV 20G
  6. Operator's manual

Husqvarna BV 20 G Operator's Manual

Hide thumbs Also See for BV 20 G:
Table of Contents

Quick Links

BV 20G
EN
Operator's manual
2-16
Table of Contents
loading

Related Manuals for Husqvarna BV 20 G

Summary of Contents for Husqvarna BV 20 G

  • Page 1 BV 20G Operator's manual 2-16...

  • Page 2: Table Of Contents

    Contents Introduction..............2 Troubleshooting............11 Safety................4 Transportation, storage and disposal......12 Assembly................ 8 Technical data ............. 12 Operation................ 8 EC Declaration of Conformity........15 Maintenance..............10 Introduction Product description For concrete layers thicker than 150 mm, vibration with an internal vibrator is necessary. The product is a vibrating walk-behind concrete screed with a gasoline combustion engine.
  • Page 3 1. Beam 2. Engine 3. Lifting eye 4. Throttle wire 5. Throttle control 6. Handle 7. Swivel 8. Vibration damping units 9. Type plate 10. Operator's manual 11. Stop button for the engine Symbols on the product WARNING: This product can be dangerous and cause serious injury or death to the operator or others.

  • Page 4: Safety

    UKCA label 1. Product type 2. Product number 3. Product weight 4. Serial number 5. Manufacturer 6. Rated power 7. Production year Product liability The product agrees with the applicable UK directives. Type plate As referred to in the product liability laws, we are not liable for damages that our product causes if: •...
  • Page 5 Safety instructions for operation in fingers, hands, wrists, arms, shoulders, and/or nerves and blood supply or other body parts. The injuries can be debilitating and/or permanent, and can increase gradually during weeks, months or WARNING: Read the warning instructions years. Possible injuries include damage to the blood that follow before you use the product.
  • Page 6 • Do not breathe the exhaust fumes. Husqvarna service agent. • Make sure that the airflow in the work area is sufficient. This is very important when you operate...
  • Page 7 To do a check of the vibration damping system • Do not use your fingers to examine the engine for leaks. 1. Make sure that there are no cracks or deformation • Keep fuel in approved containers only. on the vibration damping units. •...

  • Page 8: Assembly

    Assembly To assemble the product a) If 1 handle section is not sufficiently long, install a second handle section. 1. Remove the nut (A) and the washer (B) from the 5. Attach the throttle control to the handle with a clamp. swivel screw.
  • Page 9 necessary. Differences in the speed of the movement 4. Pull the starter rope handle until the engine starts. and the vibration frequency gives different results. To start the product 1. Set the choke control in the correct position. 5. If the choke is closed, open the choke immediately. 6.

  • Page 10: Maintenance

    8. When you start at the next section of the concrete 2. Put the handle on your shoulder. surface, put 15 cm/5.9 in. (A) of the beam on the 3. Pull the beam rearward. At the same time turn the smooth concrete surface to make an overlap.

  • Page 11: Troubleshooting

    Maintenance Each 2 After the Yearly or Each use Each 25h Each 50h years or first 10h each 100h each 300h Do a check of the fuel level and the engine oil level. Do a check of the throttle control and the throttle wire.

  • Page 12: Transportation, Storage And Disposal

    Discard all chemicals, such as engine oil or fuel, at a service center or at an applicable disposal location. • When the product is no longer in use, send it to a Husqvarna dealer or discard it at a recycling location. • During transportation, keep the engine in a vertical position to prevent fuel leakage.
  • Page 13 Handle dimensions (2 pcs) L*W, diameter, mm/in. 1800*2, 44 / 70.86*0.08, 1.73 Operation width of the beam, m/ft. 2/6.56 Lubrication Shell Regina 2 or equivalent type of grease * = For further information and questions about this specific engine, refer to the engine manual or the web site of the engine manufacturer.
  • Page 14 Min. length, mm/in. 2200/86.6 Max. length, mm/in. 4000/157.5 Height, mm/in. 350/13.8 Operation width, mm/in. 2000/78.7 1168 - 004 - 14.01.2022...

  • Page 15: Ec Declaration Of Conformity

    EC Declaration of Conformity EC Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Concrete Compactor, Vibrating Beam Brand Husqvarna Type/Model BV 20G Identification Serial numbers dating from 2021 and onwards...
  • Page 16 UK Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, SWEDEN, Tel: +46 36 146500 declare on our sole responsibility that the product: Description Concrete Compactor, Vibrating Beam Brand Husqvarna Type/Model BV 20G Identification Serial numbers dating from 2021 and onwards...
  • Page 17 1168 - 004 - 14.01.2022...
  • Page 18 1168 - 004 - 14.01.2022...
  • Page 19 1168 - 004 - 14.01.2022...
  • Page 20 www.husqvarnacp.com Original instructions 1159986-26 2022-01-14...

Table of Contents