Summary of Contents for Toshiba LTA057A341F
- Page 1 TO：Advantech Co.,Ltd. CUSTOMER APPROVAL Customer Signature： Specification for： LTA057A341F Date of issue Nov 7,2008 Great Tech Corp. 6F., NO.309, Chuang-Ching Rd., Taipei, Taiwan Tel：+886-2-27299268 Fax：+886-2-27298689...
-
Page 2: Revision History Sheet
Sheet Specification No. TENTATIVE Revision History Sheet Date Rev. Item Reason (New) Toshiba Matsushita Display Technology Co.,Ltd Date: 2008 – 11- 07 New No. LTA057A341F-14 Date: ←# Special ←& Addition ← Change... -
Page 3: Caution And Handling Precaution
Sensitive parts inside LCD module may be damaged, and dusts or scratches may cause fire or breakage of circuits or parts or surface damage of display. Toshiba Matsushita Display Technology does not warrant the modules, if customer disassembled or modified them. - Page 4 Be careful with edges of glass parts and touch panel identically. For designing the system, give special consideration that the wiring and parts do not touch those edges. Toshiba Matsushita Display Technology Co.,Ltd Date: 2008 – 11- 07 New No.
- Page 5 The performance and quality of the LCD module are warranted only when the LCD module is used within “the recommended operation conditions”. Toshiba Matsushita Display Technology never warrants the performance and quality of the LCD module when you use the LCD module over “the recommended operation conditions”, although within “the absolute maximum rating”.
- Page 6 However, there are the above performance differences by system structure, so final conclusion for the grounding should be decided after confirmation of matching with system side. Toshiba Matsushita Display Technology Co.,Ltd Date: 2008 – 11- 07 New No. LTA057A341F-14 Date: ←# Special...
- Page 7 Hold a metal frame (bezel) part with both hands when carrying a LCD module with hand. Holding FPC may cause failures, in the worst case, it may cause smoke and/or fire. Toshiba Matsushita Display Technology Co.,Ltd Date: 2008 – 11- 07 New No.
- Page 8 Handle the LCD module fingerstalls or soft and dust-free gloves that do not produce dust when performing incoming inspection of modules or assembling sets. Handling them with bare hand may damage module display quality. Toshiba Matsushita Display Technology Co.,Ltd Date: 2008 – 11- 07 New No.
- Page 9 ∗2) EXCESSIVE FORCE Avoid applying excessive force, like pushing the surface of LCD panel. This may cause scratches or breakage of the panel, or a failure of the module. Toshiba Matsushita Display Technology Co.,Ltd Date: 2008 – 11- 07 New No. LTA057A341F-14 Date: ←# Special...
- Page 10 The signal should be applied after power supplies are turned on. The signal should be removed before power supplies are turned off. The detailed sequence of power supplies and signals are described in this specifications. Toshiba Matsushita Display Technology Co.,Ltd Date: 2008 – 11- 07 New No. LTA057A341F-14 Date: ←# Special...
- Page 11 Since some of the cartons for packing or the rubber parts etc. generate corrosive gas, confirm a reliability check in the set assembling state or the packing state before the adoption. Toshiba Matsushita Display Technology Co.,Ltd Date: 2008 – 11- 07 New No.
-
Page 12: Table Of Contents
8. Packaging 8.1 Carton 9. Warranty 10. Regulation 10.1 Regulation 10.2 Environment 11. Measuring Method 11.1 Measuring Systems 11.2 Measuring Methods Toshiba Matsushita Display Technology Co.,Ltd Date: 2008 – 11- 07 New No. LTA057A341F-14 Date: ←# Special ←& Addition ← Change... -
Page 13: Scope
Sheet Specification No. TENTATIVE 1. Scope This specification is applicable to Toshiba Matsushita Display Technology's 14cm diagonal size TFT-LCD module "LTA057A341F" designed for Industrial. 2. Product Specifications 2.1 General Specifications Item Specifications Display Mode TN color(64 gray scales, 256k colors) -
Page 14: Absolute Maximum Ratings
Operation Dry Bulb Temperature [ C] Notes 5) Do not exceed the maximum current value for environmental temperature as the below LED characteristic’s chart. Toshiba Matsushita Display Technology Co.,Ltd Date: 2008 – 11- 07 New No. LTA057A341F-14 Date: ←# Special ←&... -
Page 15: Mechanical Specifications
Sheet Specification No. TENTATIVE 2.3 Mechanical Specifications 2.3.1 Weight 125 ± 30g Toshiba Matsushita Display Technology Co.,Ltd Date: 2008 – 11- 07 New No. LTA057A341F-14 Date: ←# Special ←& Addition ← Change... -
Page 16: Dimensional Outline
86.4(Active Area) 5.9+/-0.8 8.3 MAX. 8.3 MAX. 89.4 4-R0.3 4-R0.3 4-diameter 1.6 depth max 3.1 4-hole depth max 3.1 60.6 Toshiba Matsushita Display Technology Co.,Ltd Date: 2008 – 11- 07 New No. LTA057A341F-14 Date: ←# Special ←& Addition ← Change... - Page 17 Specification No. TENTATIVE (back figure) Unit : mm Standard Tolerance : ±0.5 96.4 49.1+/-1 4-diameter 2.6 depth max. 4.2 4.5+/-1 Toshiba Matsushita Display Technology Co.,Ltd Date: 2008 – 11- 07 New No. LTA057A341F-14 Date: ←# Special ←& Addition ← Change...
-
Page 18: Electrical Specifications
LE D B/ L OF F Notes 1) When turn V on and turn it off, the form of voltage should be input with no ripple signal. Toshiba Matsushita Display Technology Co.,Ltd Date: 2008 – 11- 07 New No. LTA057A341F-14 Date: ←# Special... -
Page 19: Timing Chart
Hsync t hfp t hds t hde RGB Data 1 2 3 4 NCLK Toshiba Matsushita Display Technology Co.,Ltd Date: 2008 – 11- 07 New No. LTA057A341F-14 Date: ←# Special ←& Addition ← Change... -
Page 20: Timing Specifications
Note 6) CLK count of each Horizontal Period (th) should be always the same. Vertical blanking term should be “n” X “Horizontal Period” (th). (n: integer) Frame period(tv) should be always the same. Toshiba Matsushita Display Technology Co.,Ltd Date: 2008 – 11- 07 New No. LTA057A341F-14 Date: ←# Special... -
Page 21: Reverse Function Setting
”L”(GND) or “NC”(Open)CN1: (Reverse Scan Control Terminals) Terminal No. Symbol Setting ”H”(3.3V) ”L”(GND) or “NC”(Open) Toshiba Matsushita Display Technology Co.,Ltd Date: 2008 – 11- 07 New No. LTA057A341F-14 Date: ←# Special ←& Addition ← Change... -
Page 22: Interface Connector
Note 1) NC terminal should be open. (Don’t use.) Note 2) Please connect GND pin to ground. Don't use it as no-connect nor connection with high impedance. Note 3) Refer to 2.4.7. Toshiba Matsushita Display Technology Co.,Ltd Date: 2008 – 11- 07 New No. LTA057A341F-14 Date: ←# Special... -
Page 23: Colors Combination Table
Scale of L3… ↓ White & Black Light White White L63 Note 1) L: Low level voltage, H: High level voltage Toshiba Matsushita Display Technology Co.,Ltd Date: 2008 – 11- 07 New No. LTA057A341F-14 Date: ←# Special ←& Addition ← Change... -
Page 24: Recommended Operating Conditions
RECOMMENDED LED DRIVING BLOCK DIAGRAM current output driving circuit (Customer side) Keep same wave form (peak, width & duty) for each LED lines. Toshiba Matsushita Display Technology Co.,Ltd Date: 2008 – 11- 07 New No. LTA057A341F-14 Date: ←# Special ←& Addition... -
Page 25: Electrical Characteristics
1. White 2. Yellow 3. Purple 4. Red 5. Light Blue 6. Green 7 Blue 8.Black Toshiba Matsushita Display Technology Co.,Ltd Date: 2008 – 11- 07 New No. LTA057A341F-14 Date: ←# Special ←& Addition ← Change... -
Page 26: Optical Characteristics
Note 2) The above test limit must be applied for initial use. Characteristics will be shifted by long period operation, but it is not irregular phenomena. Theoretically brightness characteristics will be decreased due to color shift due to optical components change. Toshiba Matsushita Display Technology Co.,Ltd Date: 2008 – 11- 07 New No. LTA057A341F-14 Date: ←# Special... -
Page 27: Quality
Item Description Class Important Dimensions Dimensional outline, Dimensional between Major the mounting holes. Others Dimensions specified in this specifications Minor Toshiba Matsushita Display Technology Co.,Ltd Date: 2008 – 11- 07 New No. LTA057A341F-14 Date: ←# Special ←& Addition ← Change... -
Page 28: Appearance Test
Note 2) Dusts which are bigger not less than 0.10mm (0.1≤W) shall be judged by "Average Diameter". Average Diameter D = (a+b)/2 Note 3) The dust on the surface which can be removed is not made an issue. Toshiba Matsushita Display Technology Co.,Ltd Date: 2008 – 11- 07 New No. LTA057A341F-14 Date: ←# Special... -
Page 29: Display Quality
Note 4) After the power of LCD is turned off, the last displayed image remains in the display for a few minutes. But this remained image is not Error. So phenomenon of remained display is not subject to display quality criteria. Toshiba Matsushita Display Technology Co.,Ltd Date: 2008 – 11- 07 New No. LTA057A341F-14 Date: ←# Special... -
Page 30: Reliability Test
2) Current consumption should be smaller than the specified value. 3) Appearance and display quality should not have distinguished degradation. 4) Luminance should be larger than 50% of the minimum value specified in 5.2. Toshiba Matsushita Display Technology Co.,Ltd Date: 2008 – 11- 07 New No. LTA057A341F-14 Date: ←# Special... -
Page 31: Labels
Sheet Specification No. TENTATIVE 6.7 Labels (1) Product Label The liquid crystal display module number Toshiba Matsushita Display Technology Co.,Ltd. 2-dimensional symbol LTA057A341F 8H 000001 MADE IN ***** Product code Product code: 8 000001 : Manufacturing place code & Production date... -
Page 32: Lifetime
As the result, there is possibility to have out of specification for the optical characteristics as “5.2”. But this is not irregular phenomena. Moreover, LED also has the characteristic of color shift by long period operation. Toshiba Matsushita Display Technology Co.,Ltd Date: 2008 – 11- 07 New No. LTA057A341F-14 Date: ←# Special... -
Page 33: Packaging
(3) Packaging Material Number Quantity Description Static electricity protective sack 1set Holder(inner box) Static electricity protective bag Silica gel Plastics adhesive tape Toshiba Matsushita Display Technology Co.,Ltd Date: 2008 – 11- 07 New No. LTA057A341F-14 Date: ←# Special ←& Addition ← Change... -
Page 34: Warranty
The set (which our LCD module is assembled into) to conform the regulations below, take measures in set side. Toshiba Matsushita Display Technology is not liable for the regulations to the complete set, nor can guarantee our LCD module conform the regulation by itself. - Page 35 L 0 : Luminance on the black raster (gray scale level L0) (3) Viewing Angle: Viewing angle is defined as the angles(θ, φ), in which specified contrast ratio can be obtained. (Refer to 11.1(3) for the axes.) Toshiba Matsushita Display Technology Co.,Ltd Date: 2008 – 11- 07 New No. LTA057A341F-14 Date: ←# Special...
- Page 36 Photodiode : S1223-01 HAMAMATSU PHOTONICS K.K. White Display: White Raster (gray scale level L63) Black Display: Black Raster (gray scale level L0) Toshiba Matsushita Display Technology Co.,Ltd Date: 2008 – 11- 07 New No. LTA057A341F-14 Date: ←# Special ←& Addition...