Related Manuals for Bosch GLL40-20G
Summary of Contents for Bosch GLL40-20G
- Page 1 IMPORTANT: IMPORTANT : Read Before Using Lire avant usage Operating / Safety Instructions Consignes d’utilisation / de sécurité GLL40-20G Prof essi onal GLL40 -20G English Version See page 5 1.800.544.2843 www.calcert.com [email protected]...
- Page 2 1.800.544.2843 www.calcert.com [email protected]...
- Page 3 1.800.544.2843 www.calcert.com [email protected]...
- Page 4 WARNING Make sure that this device and the tool are securely mounted before operation. AVERTISSEMENT Assurez-vous que cet appareil et l’outil sont solidement assujettis avant de les utiliser. ADVERTENCIA Asegúrese de que este dispositivo y la herramienta estén montados de manera segura antes de su utilización.
-
Page 5: Safety Symbols
Safety Symbols The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols. This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. -
Page 6: General Safety Rules
General Safety Rules Read all instructions. Failure to follow all instructions listed below may result in hazardous radiation exposure, electric shock, fire and/or serious injury. The term “tool” in all of the warnings listed below refers to your mains-operated (corded) tool or battery-operated (cordless) tool. The following labels are on your laser tool for your convenience and safety. - Page 7 ALWAYS position the laser tool securely. Damage to the laser tool and/or serious injury to the user could result if the laser tool fails. ALWAYS use only the accessories that are recommended by the manufacturer of your laser tool. Use of accessories that have been designed for use with other laser tools could result in serious injury.
- Page 8 DO NOT operate the laser tool around children or allow children to operate the laser tool. Serious eye injury could result. DO NOT use laser tools, attachments and accessories outdoors when lightning conditions are present. Do not operate the measuring tool in explosive environments, such as in the presence of flammable liquids, gases or dusts.
- Page 9 Stay alert, watch what you are doing and use common sense when operating a tool. Do not use a tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating a tool may result in serious personal injury or incorrect measurement results.
- Page 10 Do not use the tool if the switch does not turn it on and off. Any tool that cannot be controlled with the switch is dangerous and must be repaired. Store idle tool out of the reach of children and do not allow persons unfamiliar with the tool or these instructions to operate the tool.
-
Page 11: Intended Use
Intended Use The tool is intended for determining and checking horizontal and vertical lines. The measuring tool is suitable exclusively for operation in enclosed working sites. Features The numbering of the product features shown refers to the illustration of the tool on the graphic page. 7 Fastening screw of flexible 1 Laser beam outlet mounting device... -
Page 12: Technical Data
Technical Data Model Number ....... GLL40-20G Article number ......3 603 K63 V10 Working range . - Page 13 condensation which is expected. In such conditions, equipment is normally protected against exposure to direct sunlight, precipitation, and full wind pressure, but neither temperature nor humidity is controlled. Preparation Inserting/Replacing the Battery Use only alkaline batteries. To open the battery lid 4, press the latch of the battery lid 3 and fold the battery lid up.
-
Page 14: Operation
Operation Initial Operation Protect the tool against moisture and direct sun irradiation. Do not subject the tool to extreme temperatures or variations in temperature. As an example, do not leave it in vehicles for longer periods. In case of large variations in temperature, allow the tool to adjust to the ambient temperature before operation. - Page 15 To switch off the tool, slide the On/Off switch 2 to the “Off” position. When switching off, the leveling unit is locked. Application The measuring tool is used for determining and checking horizontal and vertical lines. Automatic Leveling Working with Automatic Leveling Position the tool on a level and firm base or to a tripod 12.
-
Page 16: Working Advice
Working Advice Always use the center of the laser line for marking. The width of the laser line changes with the distance. Attaching with the Flexible Mounting Device With the flexible mounting device 8, you can fasten the measuring tool to different objects ranging in thickness between 1/2 and 2-3/8 in (12 and 60 mm), such as vertical or horizontal boards or pipes. -
Page 17: Maintenance And Service
If the tool should fail despite the care taken in manufacturing and testing procedures, repair should be carried out by an authorized after-sales service center for Bosch power tools. In all correspondence and spare parts orders, please always include the 10-digit article number given on the type plate of the tool. - Page 18 MEASURING TOOL PRODUCTS Robert Bosch Tool Corporation (“Seller”) warrants to the original purchaser only, that all Bosch lasers and measuring tools will be free from defects in material or workmanship for a period of one (1) year from date of purchase.
- Page 19 THIS WARRANTY PROGRAM DOES NOT APPLY TO TRIPODS AND RODS. Robert Bosch Tool Corporation (“Seller”) warrants tripods and leveling rods for a period of one (1) year from date of purchase. THIS LIMITED WARRANTY DOES NOT APPLY TO OTHER ACCESSORY ITEMS AND RELATED ITEMS. THESE ITEMS RECEIVE A 90 DAY LIMITED WARRANTY.