Table of Contents
Table of Contents
Related Manuals for Husqvarna 125LDx
Summary of Contents for Husqvarna 125LDx
- Page 1 LD x EN FR ES...
-
Page 2: Key To Symbols Symbols
Only use non- -metallic, flexible cutting attachments, i.e. trimmer heads with trimmer line. This product is in accordance with applicable EC directives. Only intended for trimmer heads. Noise emission to the environment according to the European Community’s Directive. The machine’s... -
Page 3: Table Of Contents
... . Note the following before starting: Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice. -
Page 4: What Is What
WHAT IS WHAT? Know your trimmer 1. Trimmer head 12. Starter handle 2. Grease filler cap 13. Fuel tank 3. Bevel gear 14. Choke control 4. Cutting attachment guard 15. Primer bulb 5. Upper shaft 16. Air filter cover 6. Lower shaft 17. -
Page 5: General Safety Precautions
Personal protective equipment IMPORTANT! Whenever you use a clear- ing saw, brushcutter or trimmer you must wear personal protective equipment that is approved by the authorities. Personal protective equipment does not eliminate... -
Page 6: Machine's Safety Equipment
GENERAL SAFETY PRECAUTIONS Machine’s safety equipment This section describes the machine’s safe- ty equipment, its purpose, and how checks and maintenance should be carried out to ensure that it operates correctly. See the “What is what” section to locate where this equipment is positioned on your machine. - Page 7 See the section on “Technical data”. If an incorrect or faulty guard is fitted this can cause serious personal injury. Use of incorrectly wound trimmer line or an incorrect cutting attachment increases the level of vibration. WARNING: Overexposure to...
-
Page 8: Cutting Equipment
S The length of the trimmer line is also im- portant. A longer trimmer line requires greater engine power than a shorter trimmer line of the same diameter. -
Page 9: Assembly
S Insert hex wrench (G) in the hole to lock the shaft. S Screw on the trimmer head (H) in the op- posite direction to the direction of rota- tion. S To dismantle, follow the instructions in... -
Page 10: Fuel Handling
HUSQVARNA two- -stroke oil, which is specially formulated for our two- -stroke engines. Mixture 1:50 (2%). S If HUSQVARNA two- -stroke oil is not avail- able, you may use another two-stroke oil of good quality that is intended for air cooled engines. -
Page 11: Fuelling
FUEL HANDLING Mixing S Always mix the petrol and oil in a clean container intended for fuel. S Always start by flling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of petrol. -
Page 12: Starting And Stopping
(CAUTION! Not with your foot). Then grip the starter handle with your right hand and pull the starter cord. S Check that the trimmer head and trimmer guard are not damaged or cracked. Replace the trimmer head or trimmer guard if they have been exposed to impact or are cracked. - Page 13 STARTING AND STOPPING NOTE: If engine dies, return blue engine choke lever to the closed position and repeat starting steps. CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended. This can damage the machine.
-
Page 14: Working Techniques
Grass trimming with a trimmer head Trimming S Hold the trimmer head just above the ground at an angle. It is the end of the trimmer line that does the work. Let the trimmer line work at its own pace. Never press the trimmer line into the area to be cut. - Page 15 S Do not allow the trimmer head to con- - stantly come into contact with the ground during normal cutting. Constant contact of this type can cause damage and wear to the trimmer head.
-
Page 16: Maintenance
Carburetor Your Husqvarna product has been designed and manufactured to specifications that re- duce harmful emissions. After the engine has used 8- -10 tanks of fuel, the engine will be run- -in. -
Page 17: Spark Plug
MAINTENANCE WARNING: Mufflers get very hot during use and remain so for some time after stopping. This also ap- plies at idle speed. Contact can re- sult in burns to the skin. Remember the risk of fire! WARNING: The inside of the muffler contain chemicals that may be carcinogenic. -
Page 18: Bevel Gear
However, be- fore using the machine you should check that the bevel gear is filled three- -quarters full with grease. Use HUSQVARNA special grease. The grease in the bevel gear does not nor- mally need to be changed except if repairs... -
Page 19: Maintenance Schedule
Check that the guard is undamaged and not cracked. Replace the guard if it has been exposed to impact or is cracked. Check that the trimmer head is undamaged and not cracked. Replace the trimmer head if necessary. Check that nuts and screws are tight. -
Page 20: Technical Data Technical Data
TECHNICAL DATA Technical data Engine Cylinder displacement, cm Cylinder bore, mm Stroke, mm Idle speed, rpm Recommended max. fast idle speed, rpm Speed of output shaft, rpm Max. engine output, acc. to ISO 8893, kW Catalytic converter muffler Speed- -regulated ignition system Ignition system Manufacturer/type of ignition system Spark plug... -
Page 21: Ec- -Declaration Of Conformity (Applies To Europe Only)
DECLARATION OF CONFORMITY EC Declaration of Conformity (Only applies to Europe) We, Husqvarna Outdoor Products Italia, S.p.A., Valmadrera, Italy. Tel: +39- -0341- -203211, declare that the grass trimmer model Husqvarna 125LD 2006- -305N00001 and onwards (the year is clearly stated on the rating plate, followed by the serial number), comply with the requirements of the COUNCIL’S DIRECTIVES:... - Page 22 Trimmer Head Line Loading Instructions...
- Page 23 Plastic Blades (Tri Cut)