Available languages
Available languages
Quick Links
JS PRODUCTS | 6445 MONTESSOURI STREET, LAS VEGAS, NV 89113
(FEB 21)
Part No. 41603
Copyright © 2021 D
D
WALT
and the D
WALT Logo are trademarks of the D
®
E
E
and are used under license. The yellow/black color scheme is a trademark for D
power tools & accessories.
Definitions: Safety Guidelines
The definitions below describe the level of severity for each signal word. Please
read the manual and pay attention to these symbols.
WARNING:
Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION:
Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
(Used without word) Indicates a safety related message.
NOTICE:
Indicates a practice not related to personal injury which, if not avoided,
may result in property damage.
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D
CALL US TOLL FREE AT: 1-844-377-8451
WARNING! Read and understand all instructions.
important safety and operating instructions.
before assembling this storage rack and save it for reference.
SAVE THESE INSTRUCTIONS
TECHNICAL SPECIFICATIONS
Technical Specifications
Auto-Darkening Viewing Area
Cartridge Size
Light State
Dark State
Grind Mode
Arc Sensor
UV/IR Protection
Switching Time
Sensitivity Control
Delay Control
Power Supply
TIG AMP Rating
Operating Temperature
Storing Temperature
Weight
DXMF21011
Copyright © 2021, D
WALT
E
WALT.
E
WALT Industrial Tool Co., or an affiliate thereof
E
WALT TOOL,
E
This manual contains
Please read this manual carefully
3.86" x 2.44"
4.53" x 4.53"
DIN 4
DIN 5-8 / 9-13
Yes
4
Up to DIN 16
1/15,000 s
Digital (5 settings)
Digital (0.1-1.0 s)
1x CR2450 Li Battery, solar assist
DC ≥ 5, AC ≥ 5
23˚F to 131˚F
-4˚F to 158˚F
1.55 lb (730 g)
WARNINGS
• Important safety information enclosed. Read this manual before using this product. Failure to observe
the following warnings could result in injury.
• Arc rays can injure eyes and burn skin. Use proper eye, ear, respiratory and body protection. Welding
helmets alone do not provide unlimited protection.
• Never place this helmet and auto-darkening filter on a hot surface.
• Do not use this helmet while working with or around explosive or corrosive liquids.
• This auto-darkening helmet is not suitable for laser welding and oxyacetylene.
• Do not weld while in the overhead position while using this welding helmet and auto-darkening filter.
• Danger of explosion if battery is incorrectly replaced. WARNING: DO NOT INGEST BATTERY;
CHEMICAL BURN HAZARD. This product contains a coin/button cell battery. If the coin/button
cell battery is swallowed it can cause severe internal burns in just 2 hours and can cause death.
• Keep new and used batteries away from children. If the battery compartment does not close securely,
stop using the product and keep away from children.
• If you think batteries might have been swallowed or placed inside any part of the body, seek immediate
medical attention.
• If the coin cell battery comes in contact with the skin, immediately wash area with mild soap and water.
If coin cell battery liquid gets into the eye, rinse water over the open eye for 15 minutes or until irritation
ceases. If medical attention is needed, the battery electrolyte is composed of organic solvent and
lithium salts.
• Do not incenerate or dispose of tool together with household waste material! Tool that has reached
the end of its life must be collected separately and returned to an environmentally compatible
recycling facility.
SAFETY INSTRUCTIONS
• Before welding, always inspect the helmet and auto-darkening filter to be sure they are fitted properly
and in good condition.
• Keep the sensors, solar cells, and filter lens clean. See MAINTENANCE for details on CLEANING
AND STORAGE.
• Inspect the auto-darkening filter lens frequently and replace any scratched, cracked or pitted filter lens
or protective lens.
PARTS LIST
No.
1
2
3
4
5
6
7
8
9
WALT
E
1
OPERATION
Headgear Adjustment
1. Adjust the headgear diameter with the twist knob on the back. Twist clockwise to tighten and
counter-clockwise to loosen.
2. Adjust the height by sliding the strap to the appropriate size and snapping the pin into the hole to lock
securely in place.
3. To adjust the viewing angle, loosen the knobs on both sides of the helmet and change angle locker
to the desired tilt position (there are 5 positions with the helmet set in the middle by default.) After
achieving the desired angle, tighten the knobs until they are snug. The helmet should still swing up, but
should not drift downward when in place for welding.
4. To adjust the distance between the user's face and auto-darkening filter, loosen the knobs on both
sides of the helmet until the headband can move back and forth freely. Reposition the headband at one
of the 3 slots as desired (there are 3 positions with the helmet set in the middle by default). This should
be done one side at a time and both sides should be located at the same position for proper
auto-darkening filter operation.
Mode Control
• There are 3 modes available with the "MODE" button: "GRIND", "WELD", and "CUT.
- Selecting "GRIND" mode will be suitable for grinding applications.
- Selecting "WELD" mode will be suitable for welding applications; shades DIN 9-13 will be available.
- Selecting "CUT" mode will be suitable for cutting applications; shades DIN 5-8 will be available.
Shade Control
• Select the mode most suitable for your application. When the appropriate mode is selected, either
"WELD" or "CUT," press the "SHADE" button to cycle through the shades. Select the shade that is
most suitable for your application.
Description
Frame
Front Protective Lens (41603-FPL)
Auto-Darkening Filter (41603-ADF)
Inner Protective Lens (41603-IPL-5PK)
Welding Helmet
Right Lens
Left Lens
Sweat Band
Headgear (41603-HDGR)
7
4
5
3
2
Qty.
1
1
1
5
1
1
1
1
1
9
8
6
Summary of Contents for DeWalt DXMF21011
- Page 1 Right Lens Left Lens Sweat Band JS PRODUCTS | 6445 MONTESSOURI STREET, LAS VEGAS, NV 89113 Headgear (41603-HDGR) (FEB 21) Part No. 41603 DXMF21011 Copyright © 2021, D WALT Copyright © 2021 D WALT. WALT and the D WALT Logo are trademarks of the D WALT Industrial Tool Co., or an affiliate thereof...
-
Page 2: Troubleshooting
MIG (light) WALT et le logo D WALT sont des marques de commerce de DEWALT Industrial Tool Co. ou d’une ® TIG, GTAW société affiliée à cette dernière et sont utilisés sous licence. L’agencement de couleurs jaune et noir est une marque de commerce des outlils électriques et accessorires D... -
Page 3: Liste Des Pièces
- Le mode « COUPAGE » convient aux travaux de coupage; les nuances DIN 5-8 sont disponibles. Si pour toute raison vous n’êtes pas entièrement satisfait de votre masque de soudeur DEWALT, vous pouvez le retourner dans les 90 jours à compter de la date d’achat, accompagné du reçu, pour un Commande de L’obscurcissement... -
Page 4: Especificaciones Técnicas
GUARDE ESTAS INSTRUCCIONES FUNCIONAMIENTO Ajuste del Arnés ESPECIFICACIONES TÉCNICAS 1. Ajuste el diámetro del arnés con la perilla giratoria en la parte posterior. Gire en sentido horario para apretar y en sentido antihorario para aflojar. Especificaciones Técnicas 2. Ajuste la altura deslizando la correa al tamaño apropiado y colocando el pasador en el orificio para Área de visualización de 3.86"... -
Page 5: Solución De Problemas
SOLUCIÓN DE PROBLEMAS PROBLEMA POSIBLES CAUSAS SOLUCIÓNES SUGERIDAS Dificulad para ver a travé - La lente protectora está sucia - Limpie o reemplace la lente protectora del filtro de oscurecimiento - La lents del filtro de oscurecimiento automático - Limpie la lente del filtro automático está...