Electrolux 300 Series Use & Care Manual
Hide thumbs
Also See for 300 Series:
- Use & care manual (100 pages) ,
- Installation instructions manual (50 pages) ,
- Owner's manual (11 pages)
Related Manuals for Electrolux 300 Series
Summary of Contents for Electrolux 300 Series
- Page 1 Use & Care Manual Washing Machine Manuel d’utilisation et d’entretien Machine à laver Manual de uso y cuidado Lavadora electroluxappliances.com\register...
-
Page 2: Table Of Contents
Table of contents Please read and save this manual Important Safety Information ......2 Thank you for choosing Electrolux, our Features ..............6 premium brand in home appliances. This Use Pre-Installation Requirements ......7 & Care Manual is part of our commitment to customer satisfaction and product quality Installation ...............12... - Page 3 IMPORTANT SAFETY INFORMATION Important safety instructions Definitions Safety precautions This is the safety alert symbol. It is used DO NOT attempt to install or operate your to alert you to potential personal injury unit until you have read the safety precautions hazards.
- Page 4 IMPORTANT SAFETY INFORMATION Protect children Refer to the Installation sections of this manual for detailed grounding • DO NOT allow children to play on or in procedures. If the washer is moved the washer. Close supervision of children to a new location, have it checked is necessary when the washer is used near and reinstalled by a qualified service children.
- Page 5 IMPORTANT SAFETY INFORMATION WARNING WARNING HARMFUL VAPOR HAZARD RISK OF INJURY DO NOT WASH: Water resistant and water DO NOT use or mix liquid chlorine bleach with other household chemicals such repellent clothing or other materials. Failure to follow these instructions may as toilet cleaners, rust removers, acids such as vinegar, or products containing result in an abnormal vibrating and out-...
-
Page 6: Features
8. Serial and model # 16. Door stand ventilation Refer to the table below for an overview of features available for each model series. no yes 300 Series no yes no yes no yes yes yes yes 18 400 Series... -
Page 7: Pre-Installation Requirements
PRE-INSTALLATION REQUIREMENTS Installation Checklist Shipping Hardware Drain Foam shipping support (under wash Stand pipe or wall drain height tub) removed and stored minimum 24” Shipping bolts and spacers removed Verify anti-siphon disc is attached from rear of appliance and stored toward end of drain hose ... - Page 8 PRE-INSTALLATION REQUIREMENTS Grounding requirements NOTE The washer MUST be grounded. In the Because of potentially inconsistent event of malfunction or breakdown, voltage capabilities, the use of this washer grounding will reduce the risk of with power created by gas powered electrical shock by a path of least generators, solar powered generators, resistance for electrical current.
- Page 9 PRE-INSTALLATION REQUIREMENTS 96" (244 cm) max. 60 sq. Inches 24" (61 cm) min. NOTE 120 sq. Inches Equally Divided Split Vent Drain hose length is 59 in. (150 cm). For Door installations requiring a longer drain hose, use hose P/N 137098000, available from an authorized parts distributor.
- Page 10 PRE-INSTALLATION REQUIREMENTS 120 sq. Inches min. Louvered Opening Bi-Fold louvered doors with 120 sq. in of ventilation 120 sq. Inches of wall venting Louvered Door MIN. INSTALLATION CLEARANCES - Inches (cm) Sides Rear Front 0" 0" 0" Alcove/ Open recess (0 cm) (0 cm) (0 cm)
- Page 11 PRE-INSTALLATION REQUIREMENTS Washer dimensions 53.5" (136 cm)* to clear open door 27.0" 32" (81.25 cm)* (68.5 cm) to front of closed door water supply connection on rear of unit 38.0" (96.5 cm) power cord drain hose on on rear rear of unit of unit 53.25"...
-
Page 12: Installation
INSTALLATION Unpacking the washer Carefully return the washer to an upright position. WARNING ELECTRICAL SHOCK HAZARD Improper connection of the equipment Carefully move the washer to within 4 grounding conductor can result in a risk feet (1 m) of its final location. of electrical shock. - Page 13 Save all shipping bolts and spacers for future use. If the washer is to be transported at a later date, the shipping hardware must be reinstalled to help prevent shipping damage * on select models For 300 Series: For 400, 500, and 600 Series: Remove all of the following:...
- Page 14 Press down on (color: blue) on the left side (400, 500, alternate corners washer. 600 models only). and sides and feel On 300 series, the for the slightest cold inlet is on the movement. Adjust right side. the appropriate leg(s) so the...
- Page 15 INSTALLATION Tighten by NOTE hand until snug. Then tighten The standpipe inside diameter must be each supply 1-1/4” (3.2 cm) minimum. There must be connection an air gap around the drain hose in the another 2/3 turn standpipe. A snug hose fit can cause a with pliers.
- Page 16 INSTALLATION Reversing the door NOTE Door reversibility is available on all models. Tools needed for IMPORTANT reversal: BEFORE YOU REVERSE WASHER DOOR: 1. Be sure you have adequate swing area before reversing Screwdriver with #2 door. square bit 2. Gather your tools - including a screw driver with a #2 square bit and plastic knife (or small, flat prying tool that won’t damage paint).
- Page 17 INSTALLATION Reinstalling door lock and hole Release wiring harness from retainer on plastic terminal cap. Then release cover terminal from terminal cap. Save the cap to reinstall later. Move the plastic cover to the other side of the front panel. Position the cover so the “hook”...
- Page 18 INSTALLATION Make sure the alignment tabs reengage. Insert hinge locating pins into the hole that were previously covered by the plastic hole cover. Press on the face of the hinge to snap the other locating pins into place. Connect to Notches 4.
-
Page 19: Accessories And Replacement Parts
U.S. or 1-800-265-8352 in Canada, or visit Titanium - P/N 5304475700 our website, www.electroluxappliances.com *Other colors may be available. Contact the in the U.S. or www.electroluxappliances.ca in source where you purchased your washer. Canada for the Electrolux Authorized Parts Distributor nearest you. -
Page 20: Controls And Settings
This manual covers many models and not all cycles, options, or features listed are available on every model. Consoles shown above for reference only. Your model may differ. PODS is a registered trademark of Procter & Gamble Company, Cincinnati OH, used under license by Electrolux. ®... - Page 21 CONTROLS AND SETTINGS Settings chart - 300 series washer START PAUSE HEAVY HIGH EXTRA RINSE EXTENDED REFRESH LUXC AR E WAS H WARM NORMAL MEDIUM CALL SERVICE CANCEL FAST WASH DELAY TIME COOL LIGHT DELICATES CONTROL LOCK RINSE & SPIN...
- Page 22 PODS ® = Available selections. = Factory presets. = Non-modifiable presets. PODS is a registered trademark of Procter & Gamble Company, Cincinnati OH, used under license by Electrolux. ®...
- Page 23 PODS ® = Available selections. = Factory presets. = Non-modifiable presets. PODS is a registered trademark of Procter & Gamble Company, Cincinnati OH, used under license by Electrolux. ®...
- Page 24 PODS ® = Available selections. = Factory presets. = Non-modifiable presets. PODS is a registered trademark of Procter & Gamble Company, Cincinnati OH, used under license by Electrolux. ®...
- Page 25 CONTROLS AND SETTINGS Cycle selection To stop the cycle, press cancel. Press the power button to turn on the unit. Then, turn the cycle selector in either direction or press the cycles button NOTE (dependent on model) to scroll to the desired cycle.
- Page 26 CONTROLS AND SETTINGS Cycles LOAD LOAD TYPE CYCLE DESCRIPTION OPTIC WHITES White loads • SmartBoost action • longer agitation • optimized temperatures WHITEST WHITES White loads • longer agitation • higher temperatures WHITES White loads • longer agitation HEAVY DUTY Large heavily soiled loads •...
- Page 27 Cold water is added to cool prone to dye transfer. For use with cold down the load prior to drain and spin. water detergents. PODS is a registered trademark of Procter & Gamble Company, Cincinnati OH, used under license by Electrolux. ®...
- Page 28 CONTROLS AND SETTINGS NOTE NOTE If changes to the settings or options are The washer will ALWAYS use a small attempted after the cycle starts, you will amount of HOT water to dissolve the pack hear several beeps when the buttons are when the PODS option has been selected.
- Page 29 (on select models) After the final spin, the washer will perform a “dry” agitation to loosen the garments from the side of the drum. PODS is a registered trademark of Procter & Gamble Company, Cincinnati OH, used under license by Electrolux. ®...
- Page 30 CONTROLS AND SETTINGS Chime cancel to turn off the alert message. The washer will continue to perform rinse cycles A signal will sound at the end of each cycle until suds are removed. (and periodically during extended refresh) if Reversed Hose Detection option is activated.
- Page 31 CONTROLS AND SETTINGS Door stand ventilation Help prevent odor buildup and reduce humidity between washes by utilizing your washer’s door stand ventilation feature. Open the door, locate the stand below the door latch and rotate the stand counter- clockwise to unlock it. ...
-
Page 32: Operating Instructions
OPERATING INSTRUCTIONS Operating the washer WARNING To reduce the risk of fire, electric shock or injury to persons, read the Important Safety Instructions in this Use & Care Manual before operating your washer. WARNING CAUTION RISK OF INJURY ENTRAPMENT and TIP-OVER HAZARD DO NOT wash water resistant and water DO NOT leave the door open if there are repellent clothing or other materials. - Page 33 PODS is a registered trademark of Procter & Gamble Company, Cincinnati OH, used under license by Electrolux. ®...
- Page 34 OPERATING INSTRUCTIONS Adding laundry products Laundry product dispensers Product dispenser - three compartment dispenser (300 Series) Detergent - Liquid or Powder Liquid Bleach Liquid Fabric Softener Product dispenser - Adaptive Dispenser™ (400, 500, and 600 Series) Detergent - Detergent Pack...
- Page 35 OPERATING INSTRUCTIONS Adding laundry detergent to the Adding laundry detergent to the adaptive dispenser™ three compartment dispenser Liquid detergent Liquid or powder detergent • Use the cap or scoop provided by • Use the cap or scoop provided by the detergent to add recommended the detergent to add recommended amount of detergent to the detergent amount of detergent.
- Page 36 • Use of a fabric softener-dispensing ball is products may be added with detergent. not recommended in front load washers. PODS is a registered trademark of Procter & Gamble Company, Cincinnati OH, used under license by Electrolux. ®...
-
Page 37: Normal Operating Sounds
NORMAL OPERATING SOUNDS Normal operating sounds You may or may not hear the following sounds from your new washer: A. DRAIN HOSE The washer has a flexible drain hose to carry water from the washer to the stand pipe of your home. You will hear water flowing into your stand pipe. -
Page 38: Stain Removal Guide
STAIN REMOVAL GUIDE Stain removal procedures WARNING To reduce the risk of fire or serious injury to persons or property, comply with the basic HARMFUL VAPOR HAZARD warnings listed below: DO NOT use or mix liquid chlorine bleach • Read and comply with all instructions with other household chemicals such on stain removal products. - Page 39 STAIN REMOVAL GUIDE Stain removal suggestions STAIN TREATMENT Adhesive tape, gum, Apply ice. Scrape off excess. Place stain down on paper towels. Saturate rubber cement with prewash stain remover or nonflammable dry cleaning fluid. Baby formula, dairy Use product containing enzymes to pretreat or soak stains. Soak for products, egg 30 minutes or more.
-
Page 40: Care And Cleaning
CARE AND CLEANING Inside routine cleaning WARNING (preventative) HARMFUL VAPOR HAZARD To help prevent odors or humidity DO NOT use or mix liquid chlorine bleach accumulation leave the door open with with other household chemicals such the door stand ventilation feature (on as toilet cleaners, rust removers, acid select models) for a few hours after use or or products containing ammonia. - Page 41 CARE AND CLEANING Rinse the drawer and inserts with Remove the detergent cup and top hot tap water to remove traces of cover from the dispenser drawer. accumulated powders and liquids. 4. Remove the bottom cover from the Large amounts of fabric softener dispenser drawer.
- Page 42 CARE AND CLEANING Inside cleaning (aggressive) IMPORTANT In cases where clean washer cycle along with care and cleaning of rubber gasket See Inside Routine Cleaning for future folds isn’t done, and severe odor or residue cleaning maintenance which is necessary buildup have developed, follow the below to avoid repeating issues.
- Page 43 CARE AND CLEANING Outside routine cleaning Winterizing instructions • When washing is completed, wipe top Turn off water supply faucets. and sides of washer with a damp cloth. Disconnect hoses from water supply • Clean the cabinet with mild soap and drain water from hoses.
- Page 44 CARE AND CLEANING Water inlet hose inspection Reconnecting water supply and electrical Periodically inspect all water inlet hoses for water leaks, wear, cuts, corrosion and IMPORTANT bulges. Replace all hoses, if any sign of the above is visible. All hoses should be replaced every 5 years to reduce the risk of When reinstalling the washer after hose failures.
-
Page 45: Troubleshooting
TROUBLESHOOTING Common washing inquiries Many washing problems involve poor soil and stain removal, residues of lint and scum, and fabric damage. For satisfactory washing results, follow these suggestions provided by The Soap and Detergent Association. PROBLEM POSSIBLE CAUSES SOLUTIONS PREVENTIVE MEASURES Blue stains •... - Page 46 TROUBLESHOOTING PROBLEM POSSIBLE CAUSES SOLUTIONS PREVENTIVE MEASURES Pilling • Pilling is normal • Use a lint brush or • Use fabric softener in with synthetic and shaver to remove pills. washer to lubricate (Fibers ball up permanent press fibers. and cling to fabrics.
- Page 47 • Remove wash load immediately upon cycle completion. • Pour one cup liquid chlorine bleach in standpipe; let remain a day and flush with water. PODS is a registered trademark of Procter & Gamble Company, Cincinnati OH, used under license by Electrolux. ®...
- Page 48 TROUBLESHOOTING Before calling Before calling for service, review this list. It may save both time and expense. The list includes common occurrences that are not the result of defective workmanship or materials in this washer. PROBLEM POSSIBLE CAUSES SOLUTIONS NOISE (Please refer to Normal Operating Sounds ) High pitch “jet •...
- Page 49 TROUBLESHOOTING PROBLEM POSSIBLE CAUSES SOLUTIONS Washer does • Electrical power cord may not be • Make sure plug fits tightly in wall not start plugged in or connection may be outlet. loose. • Reset circuit breaker or replace • House fuse blown, circuit breaker fuse.
- Page 50 TROUBLESHOOTING PROBLEM POSSIBLE CAUSES SOLUTIONS Warm or hot • Hot water heater is set too low or • Measure hot water temperature at water is not hot is a distance from washer. nearby faucet with candy or meat enough thermometer. Water temperature should be at least 120°F (49°C).
-
Page 51: Limited Warranty
LIMITED WARRANTY For the applicable warranty period as set forth below, as measured from your original date of purchase, Electrolux will repair or replace any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed, used and maintained in accordance with the provided instructions. - Page 52 electroluxappliances.com...