Available languages
Available languages
Quick Links
JS PRODUCTS | 6445 MONTESSOURI STREET, LAS VEGAS, NV 89113
(MAY18)
Part No. 56831
Copyright © 2018 D
D
WALT
and the D
WALT Logo are trademarks of the D
®
E
E
and are used under license. The yellow/black color scheme is a trademark for D
power tools & accessories.
Definitions: Safety Guidelines
The definitions below describe the level of severity for each signal word. Please
read the manual and pay attention to these symbols.
WARNING:
Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION:
Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
(Used without word) Indicates a safety related message.
NOTICE:
Indicates a practice not related to personal injury which, if not avoided,
may result in property damage.
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D
CALL US TOLL FREE AT: 1-844-377-8451
WARNING! Read and understand all instructions.
important safety and operating instructions.
before assembling this storage rack and save it for reference.
SAVE THESE INSTRUCTIONS
TECHNICAL SPECIFICATIONS
Technical Specifications
Total Capacity
Capacity per Shelf
Height
Width
Depth
GENERAL SAFETY
• Keep work area clean and dry.
• Use correct/recommended tools for the job.
• Never leave unattended tools plugged in or running.
• Never force a part into place.
• Wear appropriate safety apparel for the job you are doing.
• Wear safety glasses/goggles.
• Never crawl, sit, stand, or climb on the rack.
• Keep small parts away from children. Never leave a small child unattended while assembling.
• Always use common sense – your personal safety is your responsibility.
SPECIFIC SAFETY FOR WALL MOUNT BRACKET
WARNING:
Serious injury or death can occur from the rack tipping over. To prevent this, the rack
must be secured to a wall, especially in earthquake -prone areas, or where surfaces are uneven, and where
children and/or pets are present.
Different wall materials require different types of fasteners. Use fasteners suitable for your specific type of
wall. If you are uncertain about what type of fastener to use, then please contact your local hardware store.
DXST4500
Copyright © 2018, D
WALT
E
WALT.
E
WALT Industrial Tool Co., or an affiliate thereof
E
WALT TOOL,
E
This manual contains
Please read this manual carefully
4,500 lb (2,041 kg)
*when weight is evenly distributed
1,500 lb (680 kg)
*when weight is evenly distributed
47" (119.4 cm)
49.5" (126 cm)
18" (45.7 cm)
WARNING:
FOR THIS RACK
• Maximum load for each shelf: Up to 1,500 lb (680 kg) when weight is evenly distributed.
• It is recommended that the heaviest load be placed on the bottom shelf.
Parts List
No. Description
1
Vertical Beam
2
Pre-Bolted Vertical Assembly
3
Vertical Assembly Bolt
4
Crossbeam
5
Shelf Support Strap
6
Safety Strap With Weld Nut
7
Safety Strap Bolt
8
Laminate Deck
9
Locking Shelf Pin
3
5
6
7
9
10
11
WALT
E
1
4
Tools Required for Rack Assembly: 4 mm Hex Key (included) OR 4 mm Hex Bit (included); Rubber
Mallet (not included).
BEFORE YOU BEGIN:
• Read all instructions thoroughly.
• Remove all components from the box, and lay them on the floor in an orderly fashion.
• Wear eye protection.
• Be cautious of sharp edges.
• Keep this information for further reference.
• If you are not stacking a second rack at this time, then please store the Stacking Plates for potential
future use as they will be needed.
WARNING:
Serious or fatal crushing injuries can occur from rack tipping over. To prevent this, the
assembled rack must always be secured to a wall, especially in earthquake-prone environments, where
surfaces are uneven, and where children and/or pets are present.
Expandable Upright Frame Instructions (Fig. 1-2)
NOTE: For ease of assembly, two (2) vertical beams feature pre-bolted horizontal and diagonal beams, as
well as pre-attached U-bracket covers.
1. Place one (1) vertical beam and one (1) pre-bolted vertical beam on the floor, parallel to one another
(about 18"/45.7 cm apart). The widest part of the teardrop-shaped hole pattern on each beam should
be facing upward (or away from you). (Fig. 1)
2. There are two versions of the U-bracket covers - an "A" side and a "B" side. Before moving forward,
cover the U-shaped brackets on the vertical beam with the covers by mirroring the covers on the pre-
bolted vertical assembly.
3. Insert the free end of the diagonal beam into the free end of the horizontal beam. Align the holes, and
insert both beams into the U-shaped bracket at the top of the opposing vertical beam. Use the included
hex key or drill bit to thread the vertical assembly bolt through the holes and into the weld nut attached
to the U-shaped bracket. Do not fully tighten the bolt yet. (Fig. 2)
NEVER EXCEED THE FOLLOWING WEIGHT LIMITS
Qty.
No. Description
2
10
Carriage Bolt
2
11
10 mm Nut
4
12
10 mm Wrench
6
13
4 mm Hex Key
9
14
4 mm Hex Bit
6
15
Wall Mount Bracket Assembly
12
16
Stacking Plate
3
17
U-Bracket Cover
16
READ ALL INSTRUCTIONS
Qty.
2
2
1
1
1
1
2
4
12
13
14
15
16
17
8
2
Related Manuals for DeWalt DXST4500
Summary of Contents for DeWalt DXST4500
- Page 1 Stacking Plate Laminate Deck U-Bracket Cover Locking Shelf Pin JS PRODUCTS | 6445 MONTESSOURI STREET, LAS VEGAS, NV 89113 (MAY18) Part No. 56831 DXST4500 Copyright © 2018, D WALT Copyright © 2018 D WALT. WALT and the D WALT Logo are trademarks of the D WALT Industrial Tool Co., or an affiliate thereof...
- Page 2 (Fig. 5). If you plan to stack another DXST4500 Industrial Rack on top, then DO NOT attach the third set of crossbeams to the very top of the upright frames. See Stacking Instructions.
-
Page 3: Spécifications Techniques
Assurez-vous que les traverses sont fixées au même niveau sur les deux côtés (Fig. 5). Si vous envisagez d’empiler un autre support industriel DXST4500 sur le dessus, ne fixez PAS le troisième ensemble de traverses sur le dessus des cadres verticaux. Voir les instructions d’empilement. -
Page 4: Especificaciones Técnicas
Instructions d’empilement (Fig. 14-15) GUARDE ESTAS INSTRUCCIONES REMARQUE : Chaque étagère industrielle DXST4500 est livrée avec deux plaques (2) d’empilement. Pour empiler en toute sécurité deux de ces supports, vous DEVEZ utiliser quatre (4) de ces plaques. ESPECIFICACIONES TÉCNICAS REMARQUE : Il est recommandé... - Page 5 (Fig. 5). Si tiene pensado colocar otro estante industrial DXST4500 en la parte superior, entonces NO conecte el tercer juego de travesaños en la parte superior de los marcos verticales. Consulte las instrucciones de apilamiento.
- Page 6 FIG. 13 Instrucciones de apilamiento (Fig. 14-15) NOTA: cada estante industrial DXST4500 viene con dos (2) placas de apilamiento. Con el fin de colocar juntos de forma segura dos de estos estantes, debe utilizar cuatro (4) de estas placas. NOTA: Se recomienda que una persona tenga agarrado los marcos verticales en su lugar, mientras que otra persona instala las placas de apilamiento.