D-Link dge-530t User Manual
  1. Manuals
  2. Brands
  3. D-Link Manuals
  4. Pci adapter
  5. DGE-530T
  6. User manual

D-Link dge-530t User Manual

Gigabit
Hide thumbs Also See for dge-530t:
Table of Contents

Quick Links

Table of Contents
loading

Related Manuals for D-Link dge-530t

Summary of Contents for D-Link dge-530t

  • Page 2: Preface

    Preface D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes. Manual Revisions Revision Date Description October 20, 2010 • Updated for hardware revision C...

  • Page 3: Table Of Contents

    Warranty................35 Ethernet Diagnostics Utility ............17 Registration..............40 Installation................17 Configure VLAN Settings ............19 Add a VLAN ................19 Delete a VLAN ..............20 Modify a VLAN ..............21 Cable Diagnostics Feature ............22 Wake on LAN ................23 Connecting the WoL Cable ..........24 D-Link DGE-530T User Manual...

  • Page 4: Product.overview

    Quick Install Guide CAUTION: Under ordinary circumstances, a DGE-530T card will not be affected by a static charge that may be received through your body during handling of the unit. In special circumstances, the user may carry an extraordinarily high static charge and it is good practice to reduce the charge by touching a ground before handling the adapter card.

  • Page 5: Introduction

    Introduction The D-Link DGE-530T is ideal for the small office or home office environment. After completing the steps in this manual, you will have the ability to share information and resources - such as files and printers - and take full advantage of a “connected”...

  • Page 6: Features

    Section 1 - Product Overview Features Designed for versatility and performance, the DGE-530T Network Adapter provides the following: • Universal Bus support 3.3V • Compliance with IEEE 802.3ab 1000BASE-T Gigabit Ethernet standards, IEEE 802.3u Fast Ethernet standards • Supports Wake-on-LAN •...
  • Page 7 Microsoft Windows® 2003 Microsoft Windows® XP 64-bit/32-bit Netware Server 4.x , 5.x , 6.x Linux for Kernel 2.4.x , 2.6.x Novell Netware DOS ODI DOS NDIS2 MAC OS 10.2, 10.3, 10.4 FreeBSD v4.x-v5.1 Novell Netware Client32 ODI D-Link DGE-530T User Manual...

  • Page 8: Hardware Overview

    Green light indicates there is a connection to an Ethernet device at any of the ports and the transmission Full Duplex of data is occurring at full duplex (20/200/2000Mbps). Ethernet Port Connect to a 10/100/1000 Ethernet device such as a router or hub. D-Link DGE-530T User Manual...

  • Page 9: Installation

    Step.1 - When the autorun screen appears, click Install.(this will launch the Network Utility program and install the drivers).. An Installation Wizard will guide you through the process, no matter which operating you are running. Your DGE-530T will be installed successfully in just a few moments, allowing you to enjoy the many advantages of joining an Ethernet LAN.
  • Page 10 Section 2 - Installation Step.2 - Click.Agree Step.3 - Click.OK D-Link DGE-530T User Manual...
  • Page 11 Section 2 - Installation Step.4 - Click.OK Step.5 - Click.Finish D-Link DGE-530T User Manual...

  • Page 12: Hardware Installation

    Note:.Write down the serial number and hardware revision (e.g. C1) before installing the adapter. If you contact technical support, you will need this information. 2. Insert the contact edge of the DGE-530T card into the connector of any available PCI Bus Master expansion slot. Press the card firmly into the connector such that the card’s contacts are fully seated in the connector.
  • Page 13 Once you boot your computer, Windows will automatically install your adapter. ® Windows®.XP.users: You will receive a bubble stating that Windows found the DGE-530T adapter. Windows®.7/Vista®.users: You will receive a bubble stating that Windows has finished installing the DGE-530T adapter. D-Link DGE-530T User Manual...

  • Page 14: Verify Installation

    Windows® 2000/XP: Click on the.System.icon. Click the.Hardware.tab.and then click.Device.Manager.. Windows Vista®: Click on the.System.and.Maintenance.icon and then click on.Device.Manager. Windows® 7: Click on the.System.and.Security.icon and then click on.Device.Manager under System. Step.3: Scroll down and click the plus (+) sign next to.Network.Adapters.. The D-Link.DGE-530T.Gigabit.Ethernet.Adapter.will be listed. D-Link DGE-530T User Manual...

  • Page 15: Uninstalling The Adapter

    When uninstalling the DGE-530T in Windows® 7, Vista®, and Windows® Server 2008 the following pop-up warning message will be displayed indicating an unidentified program wants to access your computer: Click.Allow Click Allow to continue with the uninstall procedure. The DGE-530T drivers are WHQL-certified and should not cause any damage to your PC. D-Link DGE-530T User Manual...

  • Page 16: Verify Connectivity

    Verify Connectivity After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e router) automatically. To verify your IP address, please see the following steps below: Windows®...

  • Page 17: Advanced.features

    Section 3 - Advanced Features Advanced Features Ethernet Diagnostics Utility Installation The following will show you how to install the D-Link Ethernet Diagnostics Utility. The utility will work with Windows® 7, Vista®, and XP. Step.1 - Click Install.Diagnostics.Utility. Step.2 - Click Next.
  • Page 18 To run the utility in the future, you can double-click the utility icon in the lower-right corner on the task bar or from the start menu (click Start > All.Programs > DLink > Diagnostics > Diagnostics.Utility). D-Link DGE-530T User Manual...

  • Page 19: Configure Vlan Settings

    Section 3 - Advanced Features Configure VLAN Settings Add a VLAN Step.1 - Open the D-Link Ethernet Diagnostic Utility and click on VLAN. Assign a VLAN ID in the box and click Add. Step.2.- Click Yes to continue. Step.3.- Your VLAN will be created which may take up to 1 minute.

  • Page 20: Delete A Vlan

    Section 3 - Advanced Features Delete a VLAN WARNING: Deleting a VLAN will remove all the VLANs. Step.1 - Open the D-Link Ethernet Diagnostic Utility and click on VLAN. Click on the VLAN you want to remove and click Delete.

  • Page 21: Modify A Vlan

    Modify a VLAN You can change existing VLAN settings and modify VLAN IDs. Follow the steps below: Step.1 - Open the D-Link Ethernet Diagnostics Utility and click on VLAN. Step.2.- Click Modify.VID and change the existing ID to your desired ID number.

  • Page 22: Cable Diagnostics Feature

    To start the diagnostic, first disconnect the cable from the remote end node so there is just an open cable connected to the DGE-530T. Then check the boxes of the items you want tested and click Start.Test. The status of the test will be displayed upon completion of the test.

  • Page 23: Wake On Lan

    • IT departments can upgrade software on computers after hours from a remote station. Launch the Ethernet Diagnostic Utility and click on the D-Link adapter. Click Wake.On.LAN to “wake up” your adapter from a remote location. D-Link DGE-530T User Manual...

  • Page 24: Connecting The Wol Cable

    The name of this function is system dependent, but may be located in a category heading titled something like Power Management. Refer to your computer’s manual for more information regarding the CMOS Setup Utility and BIOS settings. D-Link DGE-530T User Manual...

  • Page 25: Qos

    QoS. These priority tagged frames will let real-time programs optimally utilize the network bandwidth. High priority packets will be processed before low priority packets. Note: To implement QoS on the DGE-530T, it must be connected to a switch or other device that supports and is configured for 802.1p QoS.

  • Page 26: Ieee 802.1P Priority Tagging

    (requiring a direct connection to a switch) and the switch’s data buffer is about to overflow, a Pause frame will be transmitted to the DGE-530T. The ensuing idle time keeps the buffer from overflowing and prevents data from being lost. This enhancement can improve network throughput, avoid collisions and prevent lost data, helping the network achieve optimal performance.

  • Page 27: About Pci Bus

    DGE-530T Adapter serving your station (installed in your computer), and the switch through which it is connected to the LAN. The options to be negotiated between the DGE-530T and its supporting switch includes Ethernet type (1000BASE-T Gigabit Ethernet or 100BASE-TX Fast Ethernet) and duplex mode (half-duplex, being one-way-at- a-time, or full duplex, being simultaneous transmit-and receive.)
  • Page 28 If the switch does not support auto-negotiation, the (single capability) message will be recognized by the DGE-530T auto-negotiation facility, which will switch to those settings of its own capabilities, which match that of the switch.

  • Page 29: Troubleshooting

    • that the proper grade of cable is employed for the network connection; • that the supporting hub is properly qualified for the application. The DGE-530T Adapter features four LED indicators: Green light indicates a connection to a 10Mbps device. The light will blink during data transmission.

  • Page 30: Networking.basics

    Check your IP address After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e router) automatically. To verify your IP address, please see the following steps below.

  • Page 31: Statically Assign An Ip Address

    Connections Windows® 7: Click on Start > Control.Panel.>.Network.and.Internet.>.Network.and.Sharing.Center.>.Change.Adapter. Settings Step.2: Right-click on the Local.Area.Connection, which represents your D-Link network adapter, and select Properties. Step.3: Highlight Internet.Protocol.(TCP/IP) and click Properties. Step.4: Click Use.the.following.IP.address and enter an IP address that is on the same subnet as your network or the LAN IP address on your router.
  • Page 32 Set Primary DNS the same as the LAN IP address of your router (192.168.0.1). The Secondary DNS is not needed or you may enter a DNS server from your ISP. Step.5: Click OK twice to save your settings. D-Link DGE-530T User Manual...

  • Page 33: Technical.specifications

    • Novell Netware DOS ODI • Assigned by Plug and Play system • DOS NDIS2 Physical.Dimensions • MAC OS 10.2, 10.3, 10.4 • 4.8in x 2.3in (12.2cm x 5.9cm) • FreeBSD v4.x-v5.1 • Novell Netware Client32 ODI D-Link DGE-530T User Manual...

  • Page 34: Contacting.technical.support

    Contacting Technical Support D-Link provides free technical support for customers within the United States and within Canada for the duration of the warranty period on this product. U.S. and Canadian customers can contact D-Link technical support through our web site or by phone.

  • Page 35: Warranty

    Warranty Period or ninety (90) days, whichever is longer, and is subject to the same limitations and exclusions. If a material defect is incapable of correction, or if D-Link determines that it is not practical to repair or replace the defective Hardware, the actual price paid by the original purchaser for the defective Hardware will be refunded by D-Link upon return to D-Link of the defective Hardware.
  • Page 36 Software or to refund the portion of the actual purchase price paid that is attributable to the Software. Except as otherwise agreed by D-Link in writing, the replacement Software is provided only to the original licensee, and is subject to the terms and conditions of the license granted by D-Link for the Software.
  • Page 37 D-Link Systems, Inc., 17595 Mt. Herrmann, Fountain Valley, CA 92708. D-Link will not be held responsible for any packages that are lost in transit to D-Link. The repaired or replaced packages will be shipped to the customer via UPS Ground or any common carrier selected by D-Link.
  • Page 38 FOR WARRANTY SERVICE) RESULTING FROM THE USE OF THE PRODUCT, RELATING TO WARRANTY SERVICE, OR ARISING OUT OF ANY BREACH OF THIS LIMITED WARRANTY, EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE SOLE REMEDY FOR A BREACH OF THE FOREGOING LIMITED WARRANTY IS REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR NONCONFORMING PRODUCT.
  • Page 39 • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. For detailed warranty information applicable to products purchased outside the United States, please contact the corresponding local D-Link office. D-Link DGE-530T User Manual...

  • Page 40: Registration

    Appendix E - Registration Registration Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights. Version 3.0 October 20, 2010 D-Link DGE-530T User Manual...

Table of Contents