Fujitsu SK-96380-120PMC User Manual

Fujitsu SK-96380-120PMC User Manual

Mb96300 series

Quick Links

Fujitsu Microelectronics Europe
FMEMCU-UG-960019-11
User Guide
MB96300 SERIES
EVALUATION BOARD
SK-96380-120PMC
USER GUIDE
X
Table of Contents
loading

Summary of Contents for Fujitsu SK-96380-120PMC

  • Page 1 Fujitsu Microelectronics Europe FMEMCU-UG-960019-11 User Guide MB96300 SERIES EVALUATION BOARD SK-96380-120PMC USER GUIDE...
  • Page 2: Revision History

    SK-96380-120PMC User Guide Revision History Revision History Date Issue 01.12.2008 V1.0, HWe, First Release 12.12.2008 V1.1, HWe, Chapter 8 (China RoHS) and chapter 9 (Recycling) added This document contains 34 pages. UG-960019-11 - 2 - © Fujitsu Microelectronics Europe GmbH...
  • Page 3: Warranty And Disclaimer

    To the maximum extent permitted by applicable law, Fujitsu Microelectronics Europe GmbH restricts its warranties and its liability for the SK-96380-120PMC Board and all its deliverables (e.g. software include or header files, application examples, target boards, evaluation boards, engineering samples of IC’s etc.), its performance and any consequential damages, on the use of the Product in...
  • Page 4: Table Of Contents

    Alarm Comparator Connector (J2)................. 26 External Supply Voltage Vin (J3) ................26 Vcc 5 Volts (J4) ..................... 26 4.10 Vcc 3.3 Volts (J5) ....................26 4.11 LIN Bus Inhibit (J6)....................26 UG-960019-11 - 4 - © Fujitsu Microelectronics Europe GmbH...
  • Page 5 5 PROGRAMMING THE INTERNAL FLASH MEMORY........... 27 Asynchronous Mode....................27 Synchronous Mode ....................29 6 APPENDIX ........................30 Related Products....................30 7 INFORMATION IN THE WWW..................31 8 CHINA-ROHS REGULATION ..................32 9 RECYCLING ........................34 © Fujitsu Microelectronics Europe GmbH - 5 - UG-960019-11...
  • Page 6: Overview

    Chapter 1 Overview 1 Overview 1.1 Abstract The SK-96380-120PMC is a multifunctional evaluation board for the Fujitsu 16FX Flash microcontroller MB96380 Series. It can be used stand-alone for software development and testing or as a simple target board to work with the emulator system.
  • Page 7: Features

    SK-96380-120PMC User Guide Chapter 1 Overview 1.2 Features < Supports Fujitsu’s 16FX MB96380 Series with 120 pin PMC / M21 package or the MB2198 Emulator System with the Probe Cable MB2198-16FX-120P-M21 < 9-15V unregulated external DC power supply < On-board 3.3V and 5.0V switching mode voltage regulators <...
  • Page 8: General Description

    SK-96380-120PMC User Guide Chapter 1 Overview 1.3 General Description The SK-96380-120PMC supports the F MC-16FX microcontrollers of MB96380 Series with LQFP120-M21 (PMC) package. It can be used as a stand-alone evaluation board or as a target board for the emulator debugger.
  • Page 9 If the board is used as an emulator target board, the microcontroller must be removed from the socket and the corresponding probe cable has to be mounted: Series V-Chip Probe cable Socket MB2198-16FX-120P-M21 MB96380 MB96V300B NQPACK120SD, HQPACK120SD Table 1-1: Emulation System © Fujitsu Microelectronics Europe GmbH - 9 - UG-960019-11...
  • Page 10: Installation

    1. Power up the Emulator Main Unit (MB2198-01) 2. Power up the Adapter Board (MB2198-500), if needed 3. Power up the target Board (SK-96380-120PMC) To turn off the system, switch off the components in reverse order, beginning with the target Board.
  • Page 11: Default Jumper Settings For Mb96380 Series

    SOT2 : RS232 / LIN Jumper 3 pin JP40 UART2 : RS232 / LIN Jumper 3 pin JP41 UART Reset / Inverter Jumper 3 pin Open JP42 UART2 : LIN VBat Jumper 2 pin Open © Fujitsu Microelectronics Europe GmbH - 11 - UG-960019-11...
  • Page 12 Jumper 2 pin Open JP46 Direct Reset / Delayed Solder JP 3 pin JP48 MCU Reset Jumper 2 pin Closed JP78 ALARM0 Jumper 2 pin Closed L 10 Table 2-1: Jumper Settings UG-960019-11 - 12 - © Fujitsu Microelectronics Europe GmbH...
  • Page 13: Jumper Location

    SK-96380-120PMC User Guide Chapter 2 Installation 2.3 Jumper Location The following picture shows the silk plot of the starter-kit with marked default jumper settings. Figure 2-1: Default Jumper Settings © Fujitsu Microelectronics Europe GmbH - 13 - UG-960019-11...
  • Page 14: Jumpers And Switches

    MD0 MD1 MD2 nc DIP-Switch S1 (RUN Mode) Figure 3-1: MCU mode switch: RUN mode (Fixed Vector Mode) MD0 MD1 MD2 nc DIP-Switch S1 (Programming Mode) Figure 3-2: MCU mode switch: Flash Programming mode UG-960019-11 - 14 - © Fujitsu Microelectronics Europe GmbH...
  • Page 15: Power Supply (S2, Jp: 8, 15, 16, 17, 22)

    SMC (DVCC) supply voltage is set to 3.3V Closed Board is always switched on JP22 (Mains) Open Board power is controlled by switch S2 Table 3-2: Power Supply Configuration By default, all Board supplies are set to 5V. © Fujitsu Microelectronics Europe GmbH - 15 - UG-960019-11...
  • Page 16: Subclock (Jp: 1, 2)

    Pin 69 is connected to the 32 kHz sub-clock (X1A) (X1A) Pin 69 is used as port pin P04_1 Default: JP1: 1-2, JP2: 1-4 By default, the 32 kHz sub-clock-crystal is connected to the microcontroller. UG-960019-11 - 16 - © Fujitsu Microelectronics Europe GmbH...
  • Page 17: Analog Power Supply Voltage (Jp: 11, 12, 13, 14)

    JP78 One potentiometer can be connected to the ALARM0/AN8 Jumper Setting Description Closed Pin 26 (ALRAM0/AN8) of the MCU is connected to RP2 JP78 (ALARM0) Open Pin 26 (ALRAM0/AN8) of the MCU is not connected Table 3-4: Alarm Comparator © Fujitsu Microelectronics Europe GmbH - 17 - UG-960019-11...
  • Page 18: Reset Generation (Jp: 33, 41, 46, 48)

    If JP41 (DTR/DTRx) is set, the UART RESET jumper (JP33) and the according DTR/RTS (JP23 and JP38) jumper have to be set, too. If the reset LED is steadily on, check the power supply input voltage and the settings for the reset-generation by UART. UG-960019-11 - 18 - © Fujitsu Microelectronics Europe GmbH...
  • Page 19: User Buttons Sw1, Sw2, Sw3, Sw4, Sw5, Sw6 (Jp: 3, 4, 5, 6, 7)

    A 10k pull-up resistor is connected to SDA0 (SDA0) Open No pull-up resistor is connected to SDA0 Closed A 10k pull-up resistor is connected to SCL0 JP10 (SCL0) Open No pull-up resistor is connected to SCL0 © Fujitsu Microelectronics Europe GmbH - 19 - UG-960019-11...
  • Page 20: Lin / Uart

    LIN-UART0 is LIN Slave Closed LIN bus (X5 pin 1) is powered by the board JP28 (LIN Vbat) Open LIN bus (X5 pin 1) is not powered by the board Table 3-7: UART0 Settings UG-960019-11 - 20 - © Fujitsu Microelectronics Europe GmbH...
  • Page 21: Can Interfaces (Jp: 24, 26, 34, 35)

    TX0 is connected to CAN0 (X6) (CAN0 TX) JP34 Closed RX1 is connected to CAN1 (X8) (CAN1 RX) JP35 Closed TX1 is connected to CAN1 (X8) (CAN1 TX) Table 3-9: CAN Settings © Fujitsu Microelectronics Europe GmbH - 21 - UG-960019-11...
  • Page 22: Connectors

    Connected to DTR (pin 4) Can be connected with CTS by jumper Can be connected with RTS by jumper LGND Ground normally used for LIN connection Shield Ground Table 4-1: UART Connector Signals UG-960019-11 - 22 - © Fujitsu Microelectronics Europe GmbH...
  • Page 23: Can Connector (X6, X8)

    Description Not used CANL LOW-level CAN voltage input/output Ground Not used Not used Not used CANH HIGH-level CAN voltage input/output Not used Not used Shield Ground Table 4-2: CAN Connector Signals © Fujitsu Microelectronics Europe GmbH - 23 - UG-960019-11...
  • Page 24: User-Leds & Optional Lc-Display (J1)

    Figure 4-4: User LEDs/LCD 9 10 GND GND VCC DB4 DB5 DB6 Port 09_0 09_1 09_2 09_3 09_4 09_5 09_6 09_7 Table 4-3: User LEDs/LCD Pin 15: Vcc via 39S/0.5W for LCD backlight UG-960019-11 - 24 - © Fujitsu Microelectronics Europe GmbH...
  • Page 25: In-Circuit-Programming Connector (X4)

    Not used MCU mode pin MD0 Not used RSTX MCU reset signal SIN2 UART2 receive data SOT2 UART2 transmit data SCK2 UART2 clock Board supply voltage Ground Table 4-4: In-circuit programming connector © Fujitsu Microelectronics Europe GmbH - 25 - UG-960019-11...
  • Page 26: Alarm Comparator Connector (J2)

    To this connector the INH pin of the LIN1 transceiver is connected. 4.13 VCC Connector (J7) On this connector the VCC supply (see chapter 3.2) can be measured. 4.14 GND Connector (J8) Ground reference terminal GND. UG-960019-11 - 26 - © Fujitsu Microelectronics Europe GmbH...
  • Page 27: Programming The Internal Flash Memory

    (SOT2) JP40 UART2 RS232 transceiver is selected for X9 (RS232/LIN) JP42 UART2 Open X9-1 is disconnected from the power supply (Vbat) Table 5-2: Jumper Settings for Programming via UART 2 (X9) © Fujitsu Microelectronics Europe GmbH - 27 - UG-960019-11...
  • Page 28 2) Connect the configured UART (see above) to your serial PC communication port. A straight 1:1 cable connection has to be used. 3) Start the tool “Fujitsu Flash MCU Programmer” software and make the settings: Set Device Type Select COM Port...
  • Page 29: Synchronous Mode

    10 GND Figure 5-1: Flash Programming Socket Note: Please open the jumpers JP37 (SIN2) and JP39 (SOT2) in order to avoid that the synchronous programming tool drives against the on-board RS232 transceiver! © Fujitsu Microelectronics Europe GmbH - 29 - UG-960019-11...
  • Page 30: Appendix

    (Tokyo Eletech Corp. www.tetc.co.jp/e_tet.htm) < MB2198-16FX-120P-M21 Emulator probe cable for MB96F38x MCU < MB96300 Series < MB96V300 MB96300 Series Evaluation chip < MB96F38xRS Flash MCU (Single Clock) < MB96F38xRW Flash MCU (Dual Clock) UG-960019-11 - 30 - © Fujitsu Microelectronics Europe GmbH...
  • Page 31: Information In The Www

    Microcontrollers (8-, 16- and 32bit), Graphics Controllers Datasheets and Hardware Manuals, Support Tools (Hard- and Software) http://mcu.emea.fujitsu.com/ Power Management Products http://www.fujitsu.com/emea/services/microelectronics/powerman/ Media Products: SAW filters, acoustic resonators and VCOs http://www.fujitsu.com/emea/services/microelectronics/saw/ For more information about FUJITSU MICROELECTRONICS http://www.fujitsu.com/emea/services/microelectronics/ © Fujitsu Microelectronics Europe GmbH - 31 - UG-960019-11...
  • Page 32: China-Rohs Regulation

    “Year”. UG-960019-11 - 32 - © Fujitsu Microelectronics Europe GmbH...
  • Page 33 X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in SJ/T11363-2006. • Data listed in the table represents best information available at the time of publication © Fujitsu Microelectronics Europe GmbH - 33 - UG-960019-11...
  • Page 34: Recycling

    According to the European WEEE-Directive and its implementation into national laws we take this device back. For disposal please send the device to the following address: Fujitsu Microelectronics Europe GmbH Warehouse/Disposal Monzastraße 4a 63225 Langen UG-960019-11 - 34 - © Fujitsu Microelectronics Europe GmbH...

Table of Contents