Table of Contents
Quick Links
Table of Contents
Related Manuals for Fujitsu ScanZen EK6
Summary of Contents for Fujitsu ScanZen EK6
- Page 1 Consumable Replacement and Cleaning Instructions CG00002-297901 ©ScanZen...
-
Page 2: Consumables And Replacement Cycles
Consumables and Replacement Cycles To maintain high-quality scanned images, it’s important to clean your scanner regularly and replace the consumables according to their recommended life cycle. Your scanner records the number of sheets you scan. This helps you to know when you should clean and replace the consumables. -
Page 3: Replacing The Roller Set
Replacing the Roller Set The roller set consists of a brake roller and a pick roller. Here’s how to replace the rollers: 1. Remove all documents from the ADF paper chute (feeder). 2. Open the ADF. 3. Remove the brake roller. a. - Page 4 5. Attach a new brake roller on the shaft. Insert the protrusion on the shaft into the slot. Notch Brake roller Protrusion Brake roller shaft 6. Attach the shaft. a. Attach the notch, which is on the brake roller shaft, to the slot on the right then attach the left side of the shaft.
- Page 5 7. Remove the pick roller. a. Open the side guide fully to both sides. Then place your finger into the depression and open the sheet guide in the direction of the arrow. Side guide Depression Side guide Sheet guide b. Slide the pick roller and remove it from the top. CG00002-297901 ©ScanZen...
- Page 6 8. Attach a new pick roller from the bottom. a. Check the direction of the notch on the pick roller and of the small roller and insert it in the hole. Small roller Notch b. Close the sheet guide. ATTENTION: Check that the pick roller is installed properly.
-
Page 7: Checking And Resetting The Sheet Counters
Checking and Resetting the Sheet Counters Checking the sheet counters You’ll know when you need to change the consumables when the counter background color changes. The background color will become light yellow at 95,000 sheets, to alert you that the roller set needs changing soon. - Page 8 Resetting the sheet counters When you have replaced or cleaned a consumable part, reset the corresponding counter by using the following procedure. 1. Click the [Clear] button for the consumable that you replaced. 2. Click the [OK] button in the Software Operation Panel. A confirmation message appears. 3.
-
Page 9: Cleaning Materials And Locations That Require Cleaning
Cleaning Materials and Locations that Require Cleaning Cleaning Materials Name Part Number Notes F1 Cleaner PA03950-0352 1 bottle (100 ml) Moisten a cloth or Cleaning Paper with a small quantity of this liquid to wipe the scanner clean. It may take a long time to dry if an excessive amount is used. - Page 10 Location and Frequency Location Frequency Brake roller Pick roller Plastic idler roller Glass Every 3,000 sheets Ultrasonic sensor Feed roller Eject roller ATTENTION: Cleaning cycles may vary depending on the condition of the documents. Also, cleaning must be performed more frequently when the following types of documents are scanned: •...
-
Page 11: Cleaning The Outside
Cleaning the Outside The outside of the scanner, including the ADF paper chute (feeder) and stack, should be cleaned with a piece of dry cloth, or a cloth moistened with F1 Cleaner or mild detergent, or a sheet of cleaning wipes. ATTENTION: ... -
Page 12: Cleaning The Inside
Cleaning the Inside Cleaning the ADF (with Cleaning Paper) Cleaning should be performed approximately every 3,000 sheets scanned. As the scanner continues to feed the documents, paper dust will accumulate inside the ADF and it may cause scanning errors. Cleaning frequency varies depending on the types of documents you scan. For instance, it may be necessary to clean the scanner more frequently when you scan documents on which the toner is not sufficiently fused. - Page 13 Cleaning the ADF (with cloth) Cleaning should be performed approximately every 3,000 sheets scanned. As the scanner continues to feed the documents, paper dust will accumulate inside the ADF and it may cause scanning errors. Cleaning frequency varies depending on the types of documents you scan. For instance, it may be necessary to clean the scanner more frequently when you scan documents on which the toner is not sufficiently fused.
- Page 14 ATTENTION Make sure the cloth does not get caught and damage the document sensors. Brake roller (x2) Pick roller (x6) Remove the roller from the scanner. Gently wipe the surface as you rotate the roller Gently wipe the surface of the rollers manually, taking care not to damage the roller surface.
- Page 15 Ultrasonic sensor (x2) Gently wipe dirt and dust off the surface of the ultrasonic sensors. HINT: If it is difficult to clean, use a cotton swab Ultrasonic Sensor CG00002-297901 ©ScanZen...
- Page 16 Feed roller (x2) / Eject roller (x2) Turn on the scanner. The power must be turned on to rotate the feed/eject rollers for cleaning. When the operator panel is in ready status, open the ADF. When you press the scan/stop button on the operator panel for more than 2 seconds, the feed/eject rollers rotate.
- Page 17 1250 East Arques Avenue Sunnyvale, CA 94085-4701 Ph: 844-686-8448 M-F, 5am-5pm CT Email: [email protected] Visit: www.scanzen.com CG00002-297901 ©ScanZen...