Quick Links

AP2030DN
Hardware Installation and
Maintenance Guide
Issue
05
Date
2016-07-22
HUAWEI TECHNOLOGIES CO., LTD.
Table of Contents
loading

Summary of Contents for Huawei AP2030DN

  • Page 1 AP2030DN Hardware Installation and Maintenance Guide Issue Date 2016-07-22 HUAWEI TECHNOLOGIES CO., LTD.
  • Page 2 Notice The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are provided "AS IS"...
  • Page 3: About This Document

    AP2030DN Hardware Installation and Maintenance Guide About This Document About This Document Intended Audience This document describes hardware features of the AP2030DN and provides basic installation methods. This document is intended for: Network planning engineers Hardware installation engineers Commissioning engineers...
  • Page 4 This version has the following updates: Updated the packing list. Issue 02 (2015-05-18) This version has the following updates: Modified descriptions about PoE fault troubleshooting. Issue 01 (2015-01-31) Initial commercial release. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 5 5.1.4 Installing Cable Accessories............................49 5.1.5 Replacing the Mold of the Crimping Tool.........................65 5.2 Environmental Requirements for Device Operation....................68 5.2.1 Environmental Requirements for an Equipment Room.................... 68 Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 6 5.4.4 Engineering Labels for User Cables.......................... 94 5.4.5 Engineering Labels for Power Cables........................95 5.5 Guide to Using Optical Modules..........................98 5.6 Fault Tag..................................101 5.7 Installation Checklist..............................102 Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 7 AP2030DN Overview About This Chapter Huawei AP2030DN is an enterprise-level wall plate AP. It uses an 86 mm plate and can be easily installed in an 86-type box. The AP2010DN is beautifully designed, with built-in antennas, a hidden indicator, and a sliding panel. The AP2030DN can connect to wireless terminals through wireless connections or to wired terminals using wired cables.
  • Page 8 AP2030DN Hardware Installation and Maintenance Guide 1 AP2030DN Overview 1.1 Device Structure Figure 1-1 show the appearance of AP2030DN. Figure 1-1 Appearance of AP2030DN Top view Side view DC 12V Bottom view Table 1-1 describes interfaces on AP2030DN. Table 1-1 Interfaces on AP2030DN...
  • Page 9 To connect the device to a DC power source, use the power adapter delivered with the device; otherwise, the device maybe damaged. 1.2 Indicator Description AP2030DN provides only one indicator, as shown in Figure 1-2. Figure 1-2 Indicator on the AP2030DN Indicator ETH0...
  • Page 10 AP2030DN Hardware Installation and Maintenance Guide 1 AP2030DN Overview Table 1-2 Description of the indicator on the AP2030DN Type Color Status Description Default status after Green Steady on The AP is just power-on powered on and the software is not started yet.
  • Page 11 The fault cannot be automatically rectified and must be rectified manually. 1.3 Basic Specifications Table 1-3 Basic specifications of the AP2030DN Item Description Technical specifications Dimensions outside the wall 25 mm x 140 mm x 86 mm (H x W x D) Dimensions inside the wall 16.5 mm x 51.5 mm x 63.5...
  • Page 12 70 kPa to 106 kPa 1.4 Ordering Information To place an order, contact technical support personnel. Part Number Description 50082640 Broadband Network Terminal- AP2030DN-5*RJ45, 2*RJ11-11ac, 2.2 Double Frequency Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 13 2.3 Unpacking the Equipment 2.4 Determining the Installation Position 2.5 Installing the Device 2.6 Cable Connection 2.7 Checking the Device After Installation 2.8 Powering on the Device Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 14 To install APs, prepare tools listed in Table 2-1. Table 2-1 Tools Phillips screwdriver ESD gloves Diagonal pliers RJ45 crimping tool Cable cutter Wire stripper Network cable tester Multimeter 2.2 Installation Flowchart Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 15 SN label NOTE If a PoE adapter is required, you need to purchase it separately. 2.4 Determining the Installation Position Figure 2-2 shows dimensions of the AP2030DN. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 16 Hardware Installation and Maintenance Guide 2 AP Installation Figure 2-2 Dimensions of an AP2030DN (unit: mm) When determining the device installation position, comply with the following rules: Do not deploy the device in places with high temperature, dust, noxious gas, unstable...
  • Page 17 Connect the network cable to the GE/PoE interface and the phone cable to the phone interface. Install the device that has cables properly connected to the 86-type box, as shown in the following figure. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 18 Align the screw holes at the right and left of the device with the screw holes on the box and secure the device on the box with a screwdriver. Close the panel to complete installation. 2.5.2 Installing the Device into Other Junction Boxes Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 19 1 N•m Connect the network cable to the GE/PoE interface and the telephone line to the phone interface. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 20 AP with the screw holes on the mounting bracket, and secure theAP on the mounting bracket with machine screws. 1 N•m Close the panel. 2.5.3 Installing the Device on a Wall or Ceiling Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 21 Use the flat washer and self-tapping screws to fasten the mounting bracket to the wall or ceiling. If the device is installed against the wall, ensure that UP arrowhead faces upwards. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 22 Open the front panel of the device, align the the screw holes at the right and left of the AP with the screw holes on the mounting bracket, and secure theAP on the mounting bracket with machine screws. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 23 AP2030DN Hardware Installation and Maintenance Guide 2 AP Installation 1 N•m Close the panel. 2.6 Cable Connection Figure 2-3 shows interfaces of the AP2030DN. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 24 AP2030DN Hardware Installation and Maintenance Guide 2 AP Installation Figure 2-3 Interfaces of the AP2030DN Upper layer network Table 2-3 shows cable connections of the AP2030DN. Table 2-3 Cable connections Cable Description Phone cable Connects the uplink phone interface to the traditional PSTN.
  • Page 25 After the installation is complete, observe indicators on the device to determine the system running status. For details, see 1.2 Indicator Description. NOTE Do not frequently power on and off an device. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 26 Hardware Installation and Maintenance Guide 3 Logging In to the AP Logging In to the AP About This Chapter 3.1 Logging In to the Device Using STelnet/Telnet Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 27 Step 3 Start the CLI on the PC and access the IP address 169.254.1.1 of the device using STelnet V2. Step 4 Enter the user name and password as prompted to log in to the user interface. ----End Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 28 Hardware Installation and Maintenance Guide 4 Hardware Failures Hardware Failures About This Chapter This section describes common methods for troubleshooting typical hardware faults. 4.1 A Device Fails to Be Powered On Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 29 The line is faulty (the network cable or distribution frame is damaged). l The device is faulty. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 30 4. If the device still cannot be powered on, the device itself is faulty. Contact technical support personnel or Huawei agent and ask them to replace the device. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 31 5.2 Environmental Requirements for Device Operation 5.3 Equipment Grounding Specifications 5.4 Engineering Labels for Cables 5.5 Guide to Using Optical Modules 5.6 Fault Tag 5.7 Installation Checklist Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 32 Precautions for Assembly Use dedicated tools or tools delivered by Huawei and follow the methods given here during assembly. Hold terminals of cables instead of pulling the cables themselves when installing or removing cable components.
  • Page 33 Step 1 Based on the cross-sectional area of the cable conductor, strip a length of insulation coating C to expose the conductor D of length L1, as shown in Figure 5-2. The recommended values of L1 are listed in Table 5-1. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 34 When you strip a power cable, do not damage the conductor of the cable. l If the bare crimping terminal is not provided by Huawei, the value of L1 is 1 mm (0.04 in.) to 2 mm (0.08 in.) greater than the value of L.
  • Page 35 Step 5 Push the heat shrink tubing (A) toward the connector until the tube covers the crimped part, and then use a heat gun to heat the tube, as shown in Figure 5-5. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 36 Figure 5-6 Components of a JG terminal and a power cable A. JG terminal B. Heat-shrinkable tubing C. Insulation layer of a power D. Conductor of a power cable cable Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 37 NOTICE l When you strip a power cable, do not damage the conductor of the cable. l If the bare crimping terminal is not provided by Huawei, you can adjust the value of L as required. Figure 5-7 Stripping a power cable (JG terminal)
  • Page 38 Step 5 Push the heat shrink tubing toward the connector until the tube covers the crimped part, and then use a heat gun to heat the tube, as shown in Figure 5-10. Figure 5-10 Heating the heat shrink tubing (JG terminal) Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 39 5-12. The recommended values of L1 are listed in Table 5-3. NOTICE When you strip a power cable, do not damage the conductor of the cable. Figure 5-12 Stripping a power cable (cord end terminal) Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 40 Figure 5-13 Putting the cord end terminal onto the conductor Step 3 Crimp the joint parts of the cord end terminal and the conductor, as shown in Figure 5-14. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 41 5.3 (0.21) 16 (0.025) 6 (0.24) 25 (0.039) 8.7 (0.34) 35 (0.054) 10 (0.39) ----End 5.1.3 Assembling Ethernet Cables Assembling the Shielded RJ45 Connector and Ethernet Cable Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 42 Step 2 Remove a 30 mm (1.18 in.) long section of the jacket, cut off the nylon twine inside the jacket, and cut a no more than 5 mm (0.20 in.) cleft in the jacket, as shown in Figure 5-17. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 43 Along the edge of the metal shell, cut off the aluminum foil shield layer and ensure that there is no surplus copper wire. The exposed twisted-pair cable is about 20 mm (0.79 in.) long, as shown in Figure 5-19. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 44 Step 6 Align the four pairs of cables in the holder, as shown in Figure 5-22. The connections between the wires and the pins are shown in Figure 5-23 and listed in Table 5-5. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 45 Table 5-5 Connections between wires and pins (using a straight-through cable as an example) Matching Pins of Wires Wire Color White-Orange Orange White-Green Blue White-Blue Green White-Brown Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 46 Step 9 Push the metal shell toward the connector body until the wire holder and the connector body are engaged completely. Crimp the connector, as shown in Figure 5-26. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 47 Step 11 To complete the assembly of the other end, repeat Step 1 through Step ----End Assembling an Unshielded RJ45 Connector and Ethernet Cable Context Figure 5-28 shows the components of an unshielded RJ45 connector and cable. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 48 Table 5-6. Figure 5-30 Connections between wires and pins (unit: mm (in.)) White-Orange Orange White-Green Blue White-Blue Green White-Brown Pin 8 Brown Pin 1 Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 49 The contact strips must be parallel to each other, with an offset of less than ± 5°. The top margin of a strip must be parallel to the axis of the connector, with an offset of less than ± 10°. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 50 Figure 5-33 Contact strips of the same height Step 2 Hold an RJ45 connector and turn it 45°. Observe the top edges of the metal contact strips. Figure 5-34 shows an unqualified piece. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 51 Step 5 Hold the connector with the side facing towards you, and check whether you can see the cross-sections of the wires. Ensure that the ends of the wires are in good contact with the edge Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 52 Testing the Connection of Assembled Cables Context Huawei provides two types of Ethernet cables: straight-through cables and crossover cables. Straight-through cables are connected in a one-to-one manner. They are used to connect terminals such as a computer or switch to network devices.
  • Page 53 Turn the switch to the S position to slow down lighting of the indicators so that you can see the indicators more clearly, as shown in Figure 5-39. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 54 (right) section of the tester, the indicators turn on in the sequence of 3-6-1-4-5-2-7-8-G. If the indicators do not come on in this sequence, the Ethernet cable is unqualified. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 55 For example, in this document, the adapters of cable connectors have separate interfaces. In the actual situation, the adapters may have interfaces fixed on equipment. Use dedicated tools provided or specified by Huawei and follow the installation procedure described here.
  • Page 56 Sharp objects must not touch cable wiring to prevent damage to cables. To protect power cables, route power cables of the active and standby power modules separately. Installing Power Adapters Installing the OT Terminal Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 57 Figure 5-43 Installing an OT terminal, showing the orientation of crimping sleeve Place the spring washer and flat washer in turn, mount a matching screw, and fasten it clockwise, as shown in Figure 5-44. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 58 – Bend the upper OT terminal at a 45- or 90-degree angle, as shown in Figure 5-46. – Cross the two terminals, as shown in Figure 5-47. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 59 Step 1 Hold a cord end terminal upright and place it on a terminal jack, as shown in Figure 5-48. To ensure bump contact and dense connection, place the plain side of the terminal outwards. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 60 Step 3 Move the cable slightly and ensure that it is securely connected. Step 4 Before you remove a cord end terminal, loosen the screw counterclockwise. ----End Installing Ethernet Adapters Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 61 Pull the connector slightly and ensure that it is securely connected, as shown in Figure 5-52. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 62 Installing an Unshielded Ethernet Connector Procedure Step 1 Hold the male and female connectors, with the male connector facing the female connector, as shown in Figure 5-54. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 63 Step 3 A crisp click indicates that the connector is locked by the locking key. Pull the connector slightly and ensure that it is securely connected. Figure 5-56 shows an installed Ethernet connector. Figure 5-56 Installed unshielded Ethernet connector Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 64 Step 2 Clean the pins again by using dust-free cotton. If necessary, clean the pins by using an air gun. Ensure that the pins are free from any fiber or debris. ----End Installing an FC Fiber Connector Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 65 Figure 5-59 Feeding the male connector into the female connector Step 4 Fasten the locking nut clockwise and ensure that the connector is securely installed, as shown Figure 5-60. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 66 Step 1 Remove the dustproof cap of the LC fiber connector and store it for future use. Step 2 Align the core pin of the male connector with that of the female connector, as shown in Figure 5-62. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 67 Figure 5-63 Feeding the male connector into the female connector Step 4 A clicking sound indicates that the male connector is locked, as shown in Figure 5-64. Figure 5-64 Installed LC connector Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 68 (not the pigtail). When you hear a click, the fiber connector is secured by the clips (internal parts, not illustrated in the figure). Pull the fiber connector gently. If the connector does not loosen, the installation is complete. See Figure 5-67. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 69 Step 1 Remove the dustproof cap of the MPO fiber connector and store it for future use. Step 2 Align the core pin of the male connector with that of the female connector, as shown in Figure 5-69. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 70 Figure 5-70 Installed MPO fiber connector Step 4 To disassemble an MPO fiber connector, hold the shell labeled "PULL" and remove the male connector, as shown in Figure 5-71. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 71 Step 2 Hold the handles of the COAX crimping tools to open the self-locking mechanism. The jaw of the COAX crimping tools opens automatically, as shown in Figure 5-73. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 72 Figure 5-74 Removing the mold from the COAX crimping tools Step 4 Place the mold to be installed into the jaw of the COAX crimping tools and align the screw holes, as shown in Figure 5-75. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 73 Step 6 Hold the handles of the COAX crimping tools with one hand. Tighten the two fastening screws clockwise. Figure 5-77 Figure 5-78shows the mold installed in the COAX crimping tool. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 74 The equipment room should also follow local regulations concerning the industrial construction, environmental protection, fire safety, and civil air defense. Construction must conform to government standards, regulations, and other requirements. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 75 To ensure easy maintenance and management, place the equipment in different rooms. Figure 5-79 shows the layout of the equipment room. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 76 You can connect them to ground using a one megohm current-limiting resistor and connection line. Load-bearing The floor must bear loads larger than 150 kg/m (0.21 bf/in. capacity Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 77 Dust on devices may cause electrostatic discharge and result in poor contact for connectors or metal connection points. This problem can shorten the life span of devices and cause faults. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 78 Table 5-12 Requirements for corrosive gas concentration Chemical active material Unit Concentration ≤0.20 mg/m ≤0.006 mg/m ≤0.05 mg/m ≤0.01 mg/m Take the following measures to meet the requirements: Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 79 Install a lightning proof device like a lightning rod outside the room. l The lightning proof ground shares the same grounding body with the protective ground of the room. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 80 The upper end of the grounding body should be at least 0.7 m (2.30 ft) over the ground. In cold areas, bury the grounding body below the frozen ground. l Measure the grounding resistance periodically to ensure effective grounding. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 81 Use the galvanized flat steel with cross-sectional area of 40 mm x 4 mm (1.58 in. x 0.158 in.) or 50 mm x 5 mm (1.97 in. x 0.197 in.). Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 82 For power distribution capacity in the equipment room, both the working current and fault current of the devices should be considered. Ensure that independent AC power supplies Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 83 UPS can rely on concatenation or parallel connection. When an inverter or a UPS is used, the active inverter is determined by the maximum power and a backup inverter is required. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 84 Improve reliability of the AC power supply system to reduce the necessary capacity of storage batteries. For small offices, increase the capacity of storage batteries if it is difficult to enhance reliability of the AC power supply system. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 85 The grounding resistance in an area where the earth resistance rate is high should be less than 10 ohms. 5.3.3 Grounding Specifications for Devices Table 5-17 lists the equipment grounding specifications. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 86 If the power supply and the equipment are in the same equipment room, use the same protective ground bar for them if possible. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 87 Table 5-20 Specifications for laying out ground cables Description The grounding wire should not run parallel to or twist around the signal cable. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 88 Color: chalk white Material: polyester (PET) Ambient temperature: -29°C (-20.2°F) to +149°C (300.2°F) Printed by a laser printer and written with a marker Pass UL and CSA authentication Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 89 The identification plate has an embossed area 0.2 mm x 0.6 mm (0.008 in. x 0.02 in.) around (symmetric on both sides), and the area in the middle is for affixing the label, as shown in Figure 5-82. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 90 Template for Printing You can obtain a template from the Huawei local office to print labels. The template is made in Microsoft Word. Follow these instructions to use the template: You can modify the contents of the template. Do not change settings of centered characters, direction, and fonts.
  • Page 91 After the page setup has been made correctly, save it for future use. This page setup is only necessary the first time you use the template to print the labels. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 92 Table 5-21 Standard typeface for handwriting Determine the size of characters based on the number of letters or digits and ensure that the characters are distinct and tidy. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 93 – The identification card should be downward when you lay out the cable horizontally. Figure 5-85 Text area of the label Procedure for attaching labels Figure 5-86 shows the methods and procedures for attaching labels. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 94 The identification card is to the right of the cable in vertical cabling. The identification card is on the top of the cable in horizontal cabling. Make sure that the label is facing out. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 95 The side with "TO:" that is facing outside carries the location information of the opposite end; and the other side carries the location information of the local end. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 96 C: physical slot Numbered in top-down and left-right order starting number from 01. For example, 01 is the first slot at the top left of the chassis. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 97 Table 5-23 Information on labels affixed to a fiber between a device and an ODF Content Meaning Example MN-B-C-D- MN: cabinet For example, A01. number B: chassis Numbered in bottom-up order with two digits, for number example, 01. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 98 Example of the Label Figure 5-90 shows a sample label on an optical fiber. Figure 5-90 Sample label on an optical fiber between the device and the ODF Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 99 The contents of the labels for network cables connecting hubs and devices or agents and the network cables for other purposes should be specified according to actual connections. The details are as follows: Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 100 Table 5-25 Contents of the engineering labels for user cables Content Meaning Example MN-B-C-D MN: cabinet For example, A01 is the first cabinet in row A. number Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 101 "MDF-G01-01-01" indicates that the opposite end of the user cable is connected to the terminal in row 01, column 01 of the MDF in row G, column 01 in the equipment room. 5.4.5 Engineering Labels for Power Cables Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 102 For details, see Figure 5-93. Figure 5-93 Example of the labels for DC power cables Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 103 The label only carries location information about the opposite equipment and the power socket; information about the local end is unnecessary. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 104 The system may fail to obtain information about non-Huawei-certified optical modules or obtain incorrect information. You are advised to use Huawei-certified optical modules. Obtain the electronic label of the optical module and contact technical support personnel to confirm whether it is a Huawei-certified optical module.
  • Page 105 This protects the receptacle against contamination on the surface of the optical connector. Figure 5-96 Cleaning optical fibers with special cleaning tissues Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 106 Clean a receptacle with a cotton swab, as shown in Figure 5-100. Clean an optical connector with cleaning tissues. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 107 If a fiber is inserted into an optical module of a different mode, faults may occur. For example, optical signals will be lost. 5.6 Fault Tag *Customer name: Address: Contact person: Tel.: Fax: Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 108 5.7 Installation Checklist Applic pone able Check Item Scope Indepen The air vent of the device is free from blockage to ensure dent AC normal heat dissipation. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 109 You are advised to configure dual power modules for a PoE General switch for power redundancy backup and providing power for more APs. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 110 If APs are placed in a network box, ensure that the box is well-ventilated, clean, and dustless, and the ventilation holes are not blocked. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 111 Signal cable connectors are correctly installed and securely connected to the device. Wires of each signal cable are General securely cramped in the connectors and pass connectivity tests. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 112 Fiber connectors and optical ports that are not used must be protected with protective caps or plugs. Cleaning must be carried out in strict accordance with Huawei tool specifications. The feeder cables shall not be bent or twisted, with no copper General wire exposed.
  • Page 113 The bare wires of network and feeder cables should be Outdoor covered by the winding pipes, flexible metal conduit, PVC pipes, or galvanization pipes. The cable outlet and inlet are sealed to prevent dusts. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 114 When outdoor APs use single-polarized antennas, the Outdoor horizontal distance between 2.4G antennas should be at least antenna 1 m and that between 5G antennas should be at least 0.5 m. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 115 General modul used with a multimode optical module. On most optical modules, the fibers of different types cannot be used together. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 116 If a short-distance optical fiber is used for a long-distance optical module, especially in loopback scenarios, use an General optical attenuator to prevent the optical module from being burnt. Issue 05 (2016-07-22) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 117 AP2030DN Product Description Issue Date 2015-03-10 HUAWEI TECHNOLOGIES CO., LTD.
  • Page 118 Notice The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are provided "AS IS"...
  • Page 119 Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance deterioration, or unanticipated results. NOTICE is used to address practices not Issue 01 (2015-03-10) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 120 Changes between document issues are cumulative. The latest document issue contains all the changes made in previous issues. Changes in Issue 01 (2015-03-10) This is the initial commercial release. Issue 01 (2015-03-10) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 121: Table Of Contents

    1.1 Product Positioning ............................... 1   1.2 Product Characteristics ..............................3   2 Hardware Structure........................6   2.1 AP2030DN ..................................6   3 Product Features ..........................9   3.1 WLAN Features ................................9   3.2 Network Features ................................9  ...
  • Page 122: Product Positioning And Characteristics

    It provides comprehensive service support capabilities and features high security, simple network deployment, automatic AC discovery and configuration, and real-time Issue 01 (2015-03-10) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 123 This makes it the ideal choice of customers to construct indoor distributed networks. The following figure shows typical AP2030DN networking. Issue 01 (2015-03-10) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 124: Product Characteristics

    In this networking, the AP functions as a Fit AP. The AC is responsible for user access, AP go-online, AP management, authentication, routing, security, and QoS. Huawei products that provide the AC function include the AC6605, AC6005, ACU2 (with S7700, S9700, or S12700), S5720HI, S7700 (with X series board), S9700 (with X series board), and S12700 (with X series board).
  • Page 125 Has strong environment adaptability. The AP can automatically networking and select the transmission rates, channels, and transmit power to environment adapt to various radio environments and avoid interference in real Issue 01 (2015-03-10) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 126 Allows real-time monitoring on the network management system (NMS) to facilitate remote configuration and fast fault location. Supports the Link Layer Discovery Protocol (LLDP) to implement automatic link discovery and obtain the network topology. Issue 01 (2015-03-10) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 127: Hardware Structure

    The actual device appearance may be different from the following device appearance; these differences will not affect device functions. Figure 2-1 Appearance Port Figure 2-2 shows ports on the device. Issue 01 (2015-03-10) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 128 After the system is reset and starts uploading the startup after software, the indicator blinks green once. Until the blinking software is uploaded and started, the indicator Issue 01 (2015-03-10) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 129 A fault that affects services has occurred, such as a DRAM detection failure or system software loading failure. The fault cannot be automatically rectified and must be rectified manually. Issue 01 (2015-03-10) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 130: Product Features

    Control and Provisioning of Wireless Access Points (CAPWAP) Automatic login Extended Service Set (ESS) Multi-user CAC 3.2 Network Features Network features supported by the AP are as follows: Issue 01 (2015-03-10) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 131: Qos Features

    WEP authentication/encryption using a 64-bit, 128-bit, or 152-bit encryption key WPA/WPA2-PSK authentication and encryption (WPA/WPA2 personal edition) WPA/WPA2-802.1x authentication and encryption (WPA/WPA2 enterprise edition) WPA-WPA2 hybrid authentication WAPI authentication and encryption Issue 01 (2015-03-10) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 132: Maintenance Features

    (at 2.4 GHz frequency band only), wireless audio transmitters (at both the 2.4 GHz and 5 GHz frequency bands), wireless game controllers, and microwaves. Works with eSight to locate and perform spectrum analysis on interference sources. Issue 01 (2015-03-10) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 133: Technical Specifications

    AP2030DN Product Description 4 Technical Specifications Technical Specifications 4.1 Basic Specifications Table 4-1 Basic specifications of the AP2030DN Item Description Technical specifications Dimensions outside the wall 25 mm x 140 mm x 86 mm (H x W x D) Dimensions inside the wall 16.5 mm x 51.5 mm x 63.5...
  • Page 134: Radio Specifications

    5 GHz: 20 dBm power NOTE The actual transmit power depends on local laws and regulations. The AP2030DN uses a 86-type box and applies only to countries and regions that support 86-type boxes. You can adjust the transmit power from the maximum transmit power to 1 dBm, with a step of 1 dB.
  • Page 135 -72 dBm @ MCS15 MCS15 5 GHz 5 GHz 5 GHz 802.11a 802.11n (HT20) 802.11n (HT40) (non-HT20) -94 dBm @ -91 dBm @ -94 dBm @ 6 Issue 01 (2015-03-10) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 136 -80 dBm @ MCS3NSS1 MCS3NSS1 MCS3NSS1 -83 dBm @ -80 dBm @ -77 dBm @ MCS4NSS1 MCS4NSS1 MCS4NSS1 -78 dBm @ -76 dBm @ -73 dBm @ Issue 01 (2015-03-10) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 137: Standards Compliance

    -60 dBm @ MCS9NSS2 MCS9NSS2 4.3 Standards Compliance Safety standards UL 60950–1 IEC 60950–1 EN 60950–1 GB 4943 Radio standards ETSI EN 300 328 ETSI EN 301 893 Issue 01 (2015-03-10) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 138 Advanced Encryption Standards (AES) and Temporal Key Integrity Protocol (TKIP) EAP Type (s) Environment Standards ETSI 300 019-2-1 ETSI 300 019-2-2 ETSI 300 019-2-3 ETSI 300 019-1-1 ETSI 300 019-1-2 ETSI 300 019-1-3 Issue 01 (2015-03-10) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
  • Page 139 AP2030DN Product Description 4 Technical Specifications CENELEC EN 62311 CENELEC EN 50385 RSS-102 RoHS Directive 2002/95/EC & 2011/65/EU Reach Regulation 1907/2006/EC WEEE Directive 2002/96/EC & 2012/19/EU Issue 01 (2015-03-10) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.

Table of Contents