Quick Links
Honeywell IdentIPoint
Intelligent Smartcard Readers
WARNING: This equipment
generates, uses, and can radiate
radio frequency energy, and if not installed
and used in accordance with the Instructions
Manual, may cause interference with radio
communication. It has been tested and found
to comply with the limits for a Class B
computing device pursuant to Subpart J of
Part 15 of FCC Rules, that are designed to
provide reasonable protection against such
interference when operated in a residential
and commercial environment. Operation of
this equipment in a residential area is likely
to cause interference, in which case, users
at their own expense will be required to take
whatever measures may be required to
correct the interference. Any unauthorized
modification of this equipment may result in
the revocation of the owner's authority to
continue its operation.
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment .This equipment should be installed
and operated with minimum distance 20cm
between the radiator& your body.
WARNING: Fire Safety and Liability
Notice: Never connect card readers
to any critical entry, exit door, barrier,
elevator or gate without providing an
alternative exit in accordance with all fire and
life safety codes pertinent to the installation.
These fire and safety codes vary from city to
city and you must get approval from local fire
officials whenever using an electronic
product to control a door or other barrier.
QUICK INSTALLATION GUIDE
Use of egress buttons, for example, may be
illegal in some cities. In most applications,
single action exit without prior knowledge of
what to do is a life safety requirement.
Always make certain that any required
approvals are obtained in writing. Verbal
approvals are not valid. Wiring of door
strikes and locks would also accordingly
follow either a fail-safe or fail-secure
configuration.
WARNING: Earth ground all
enclosures for proper installation. It is
mandatory to use body earth on the terminal
of the fingerprint reader.
WARNING: Exit switch wiring must
be completed within the protected
area or not readily accessible outside the
protected area.
WARNING: Use suppressors on all
door locks. Use 14507020-001 diode
suppression network. Honeywell
recommends only DC locks.
CAUTION: If the bus wiring enters or
exits the building, the protectors listed in
Installation Manual must be used. Bus length
for RS485 must not exceed 500m end-to-
end.
1
Honeywell
95-7771
Related Manuals for Honeywell IdentIPoint
Summary of Contents for Honeywell IdentIPoint
- Page 1 Honeywell Honeywell IdentIPoint Intelligent Smartcard Readers QUICK INSTALLATION GUIDE Use of egress buttons, for example, may be WARNING: This equipment illegal in some cities. In most applications, generates, uses, and can radiate single action exit without prior knowledge of radio frequency energy, and if not installed what to do is a life safety requirement.
-
Page 2: Before Installation
1. Verify the mounting locations with the job Anchors – 3 each drawings. 3. Extra Tamper Resistant Screws – 2 2. Unpack the IdentIPoint reader, IOM and accessories and check them. Report any 4. Tool for Tamper Resistant Screw – 1 damaged or missing components to a 5. - Page 3 1. Fig.1 and Fig.2 show the parts of the catches on the back-plate and push it IdentIPoint reader. Use the back-plate of downwards until it hooks into place firmly. the reader to mark out the position of the See Fig.7 and Fig.8.
- Page 4 Honeywell IdentIPoint Intelligent Smartcard Readers 3. Route the field wiring including the Ethernet pigtails inside the gang-box. Set the S1 DIP cable (if required) from the conduits into the switch if the reader is to be connected to an gang-box. Clip the square ferrite clip on the IOM via RS485.
- Page 5 (SHOWN IN CALLOUT) (SHOWN IN CALLOUT) FACTORY RESET FACTORY RESET SWITCH SWITCH OPTICAL TAMPER OPTICAL TAMPER SENSOR SENSOR HOLE FOR TAMPER- HOLE FOR TAMPER- RESISTANT SCREW RESISTANT SCREW READER BACK READER BACK Fig.2. Parts of IdentIPoint reader – Back of reader 95-7771...
- Page 6 Honeywell IdentIPoint Intelligent Smartcard Readers CUT AN OPENING IN THE CUT AN OPENING IN THE DRYWALL FOR ROUTING THE DRYWALL FOR ROUTING THE WIRES. THE OPENING MUST WIRES. THE OPENING MUST HAVE THE SAME DIMENSIONS HAVE THE SAME DIMENSIONS AS THAT IN THE BACK-PLATE.
- Page 7 Honeywell IdentIPoint Intelligent Smartcard Readers CLIP ROUND FERRITE CLIP ON CLIP ROUND FERRITE CLIP ON THE FIELD ETHERNET CABLE THE FIELD ETHERNET CABLE WITH TWO TURNS WRAPPED WITH TWO TURNS WRAPPED ROUTE THE RJ45 CONNECTOR ROUTE THE RJ45 CONNECTOR (IF REQUIRED) AND MOLEX...
- Page 8 Honeywell IdentIPoint Intelligent Smartcard Readers HOLD THE 9 AND 10-PIN HOLD THE 9 AND 10-PIN MOLEX TERMINALS MOLEX TERMINALS PERPENDICULAR TO THE PERPENDICULAR TO THE BOTH MOLEX TERMINALS BOTH MOLEX TERMINALS BACK OF THE READER AND BACK OF THE READER AND...
- Page 9 Honeywell IdentIPoint Intelligent Smartcard Readers ALIGN THE MOUNTING ALIGN THE MOUNTING SLOTS BEHIND THE SLOTS BEHIND THE READER WITH THEIR READER WITH THEIR CORRESPONDING CORRESPONDING CATCHES ON THE CATCHES ON THE BACK-PLATE. PUSH BACK-PLATE. PUSH THE READER THE READER DOWNWARDS UNTIL IT...
- Page 10 Honeywell IdentIPoint Intelligent Smartcard Readers LED INDICATORS AT THE BACK Marking Marking Color Color Description Description 10/100 10/100 Green Green On when network is 100 On when network is 100 MBit MBit Activity Activity Orange Orange Flashes on network activity Flashes on network activity Power Power Blue Blue On if power on On if power on Power Power CONNECTORS AT THE BACK...
-
Page 11: Input/Output Module
Honeywell IdentIPoint Intelligent Smartcard Readers terminal(s) in their correct slots on the PCB. See Fig.15. For IOM connection details INPUT/OUTPUT MODULE see Fig.17. Drop the excess wire lengths behind the drywall. Set the S1 DIP switch if Drywall Mounting the IOM is to be connected to a reader via RS485. - Page 12 Honeywell IdentIPoint Intelligent Smartcard Readers 3. Route the field wires from the conduits into the gang-box and bring them inside the IOM via the knock-out holes. 4. The IOM can now be mounted on the wall. Hold the back half in position over the gang-box and wall.
- Page 13 Honeywell IdentIPoint Intelligent Smartcard Readers POWER, POWER, FRONT COVER FRONT COVER BACK HALF OF BACK HALF OF DATA AND DATA AND OF THE IOM OF THE IOM THE IOM THE IOM TAMPER TAMPER INDICATION INDICATION LEDS LEDS Power Power Data...
- Page 14 Honeywell IdentIPoint Intelligent Smartcard Readers IOM BACK HALF - OPEN IOM BACK HALF - OPEN HOLE FOR HOLE FOR TAMPER- TAMPER- RESISTANT RESISTANT SCREW SCREW BACK KNOCK- BACK KNOCK- OUTS FOR CABLE OUTS FOR CABLE HOLES (2) HOLES (2) COVER TAMPER...
- Page 15 Honeywell IdentIPoint Intelligent Smartcard Readers CUT OPENINGS IN THE CUT OPENINGS IN THE DRYWALL FOR ROUTING THE DRYWALL FOR ROUTING THE WIRES. THE OPENINGS MUST WIRES. THE OPENINGS MUST HAVE THE SAME DIMENSIONS HAVE THE SAME DIMENSIONS AS THAT IN THE BACK HALF OF AS THAT IN THE BACK HALF OF THE IOM.
- Page 16 Honeywell IdentIPoint Intelligent Smartcard Readers GANGBOX EMBEDDED IN WALL GANGBOX EMBEDDED IN WALL PUNCH ADDITIONAL HOLES PUNCH ADDITIONAL HOLES IN THE WALL FOR THE IN THE WALL FOR THE OTHER SCREWS OTHER SCREWS USE THE SCREWS PROVIDED USE THE SCREWS PROVIDED...
- Page 17 Honeywell IdentIPoint Intelligent Smartcard Readers ROUTE THE WIRES ROUTE THE WIRES THROUGH THE THROUGH THE KNOCKED OUT HOLES KNOCKED OUT HOLES AND FIX THEM TO THE AND FIX THEM TO THE CORRECT TERMINALS CORRECT TERMINALS ON THE PCB USING THE...
- Page 18 Honeywell IdentIPoint Intelligent Smartcard Readers USE THE ALLEN USE THE ALLEN WRENCH TO WRENCH TO SECURE THE FRONT SECURE THE FRONT COVER OF THE IOM COVER OF THE IOM TO THE BACK HALF TO THE BACK HALF WITH TAMPER- WITH TAMPER-...
- Page 19 Honeywell IdentIPoint Intelligent Smartcard Readers Position Position Description Description Address value 1 Address value 1 Address value 2 Address value 2 Address value 4 Address value 4 S2: Initialization Address value 8 Address value 8 Button Address value 16 Address value 16 S4: Cover tamper Address value 32 Address value 32 detection switch Address value 64 Address value 64 For IOM setup, normally set to OFF For IOM setup, normally set to OFF Switch Switch Description Description Position Position Effect when “ON” Effect when “ON” (Position Up) (Position Up) RS485 Termination Control DIP switch RS485 Termination Control DIP switch...
-
Page 20: Wiring Diagrams
Honeywell IdentIPoint Intelligent Smartcard Readers APPENDIX WIRING DIAGRAMS To LAN To LAN Ethernet SAI‐1‐GND Power‐OUT To Door Sensor 1KΩ 2KΩ Power‐GND SAI‐1 SAI‐0‐GND RS485‐A 1KΩ 2KΩ To REX Switch To REX Switch RS485‐B SAI‐0 Relay‐NO RS485‐GND To Door Lock To Door Lock Relay‐NC DOGnd Relay‐C SAI‐2 DC – Power Power‐GND 12 to 24V SAI‐2‐GND Power‐IN If POE is not used... - Page 21 Honeywell IdentIPoint Intelligent Smartcard Readers To LAN Ethernet Power‐OUT SAI‐1‐GND SAI‐1 Power‐GND SAI‐0‐GND RS485‐A RS485‐B SAI‐0 Relay‐NO RS485‐GND Relay‐NC DOGnd Relay‐C DC – Power SAI‐2 Power‐GND 12 to 24V SAI‐2‐GND Power‐IN If POE is not used Frame‐GND IdentIPoint Reader LEGEND LEGEND DI‐0 DI‐0 Power – Min. 18 AWG Power – Min. 18 AWG DO‐0...
- Page 22 Honeywell IdentIPoint Intelligent Smartcard Readers Connections on IN side LEGEND Power – Min. 18 AWG Power Gnd – Min. 18 AWG Power – Min. 18 AWG Power Gnd – Min. 18 AWG CAT5 Signal/Power – Min. 18 AWG Ethernet Signal – Min. 18 AWG Signal –...
- Page 23 Honeywell IdentIPoint Intelligent Smartcard Readers Connections on OUT side Ethernet To LAN Power‐OUT Power‐OUT SAI‐1‐GND SAI‐1‐GND Power‐GND Power‐GND SAI‐1 SAI‐1 SAI‐0‐GND SAI‐0‐GND RS485‐A RS485‐A RS485‐B RS485‐B SAI‐0 SAI‐0 Relay‐NO Relay‐NO RS485‐GND RS485‐GND Relay‐NC Relay‐NC DOGnd DOGnd Relay‐C Relay‐C SAI‐2 SAI‐2 Power‐GND Power‐GND SAI‐2‐GND SAI‐2‐GND Power‐IN...
- Page 24 Honeywell IdentIPoint Intelligent Smartcard Readers Ethernet Ethernet SAI‐1‐GND Power‐OUT Frame‐GND Frame‐GND Power‐IN Power‐IN SAI‐2‐GND SAI‐2‐GND Power‐GND Power‐GND SAI‐1 Power‐GND SAI‐2 SAI‐2 Relay‐C Relay‐C SAI‐0‐GND RS485‐A DOGnd DOGnd Relay‐NC Relay‐NC RS485‐B SAI‐0 Relay‐NO Relay‐NO Relay‐NO RS485‐GND RS485‐GND RS485‐GND SAI‐0 SAI‐0 Relay‐NC RS485‐B...
- Page 25 Honeywell IdentIPoint Intelligent Smartcard Readers LEGEND Power – Min. 18 AWG Power Gnd – Min. 18 AWG Ethernet Power‐OUT SAI‐1‐GND Fig.22. Reader and strike la Power‐GND SAI‐1 SAI‐0‐GND RS485‐A RS485‐B SAI‐0 DC – Power 12VDC/24VDC Relay‐NO RS485‐GND Relay‐NC DOGnd Relay‐C SAI‐2...
- Page 26 Honeywell IdentIPoint Intelligent Smartcard Readers LEGEND Power – Min. 18 AWG Power Gnd – Min. 18 AWG Ethernet Fig.24. Reader and magnetic Power‐OUT SAI‐1‐GND lock Power‐GND SAI‐1 SAI‐0‐GND RS485‐A DC – Power RS485‐B 12VDC/24VDC SAI‐0 Relay‐NO RS485‐GND Relay‐NC DOGnd Relay‐C SAI‐2 Power‐GND...
- Page 27 Honeywell IdentIPoint Intelligent Smartcard Readers 1KΩ 1KΩ SAI-n SAI-n Sensor Sensor Switch Switch SAI-n GND SAI-n GND Fig.26. Supervisory Analog Inputs Note: Door sense is considered open when sensor switch is open EACH DOOR STRIKE REQUIRES A EXIT SWITCH: WIRING MUST BE 14507020‐001 DIODE SUPPRESSION COMPLETED WITHIN THE PROTECTED NETWORK. DOOR STRIKE MAY DRAW A AREA OR NOT READILY ACCESSIBLE OUTSIDE THE MAXIMUM CURRENT OF 2A; REGULATED 12/ 24 ...
-
Page 28: Termination Setting
RS485 TERMINATION SETTING bus should have their RS485 termination turned on. It is also Both IdentIPoint readers and IOMs are recommended to turn on the pull-up and equipped with a termination circuit and pull-down resistors in the IdentIPoint... - Page 29 Honeywell IdentIPoint Intelligent Smartcard Readers IOM ADDRESS SET UP To work out the address, select a combination of bit locations on the Each IOM should have its own DIP switch. Each bit has its own address. The address could range value representation.
-
Page 30: Section 207 European Union
Honeywell IdentIPoint Intelligent Smartcard Readers CERTIFICATIONS EN 50134-1:2000 Readers EN 50134-3:2001 EN 60950-1:2001 C-tick EN 301 489-01 V1.6.1 IP-65 (Basic Outdoor EN 301 489-03 V1.4.1 Version Only) EN 300 330-02 V1.3.1 United States ... - Page 31 In no event is Honeywell liable to anyone for any direct, special, or consequential damages. The information and specifications in this document are subject to change without notice.
- Page 32 Honeywell IdentIPoint Intelligent Smartcard Readers Honeywell Building Solutions North America: 1985 Douglas Drive North Golden Valley, MN 55422-3992 +1-800-345-6770, ext. 606 Europe, Middle East, Africa & India: Honeywell House Arlington Business Park Bracknell, United Kingdom RG12 +44 (0)870 600 1659...