Husqvarna BG Combi Operator's Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Trowels
  5. BG Combi
  6. Operator's manual

Husqvarna BG Combi Operator's Manual

Hide thumbs

Quick Links

BG Combi
EN
Operator's manual
2-20
loading

Related Manuals for Husqvarna BG Combi

Summary of Contents for Husqvarna BG Combi

  • Page 1 BG Combi Operator's manual 2-20...

  • Page 2: Table Of Contents

    Contents Introduction..............2 Troubleshooting............13 Safety................4 Transportation, storage and disposal......14 Operation................ 7 Technical data.............. 16 Maintenance..............10 EC Declaration of Conformity........20 Introduction Product overview 1. Blade adjustment knob 15. Socket for power cord 2. Quick stop handle 16. Start button 3.
  • Page 3 Intended use Rating plate The product is for professional operation only. The product is used to give a smooth surface on wet concrete floors. Do not use the product for other tasks. Symbols on the product WARNING: This product can be dangerous and cause serious injury or death to the operator or others.

  • Page 4: Safety

    • the product is repaired with parts that are not from • the product is not repaired at an approved service the manufacturer or not approved by the center or by an approved authority. manufacturer. • the product has an accessory that is not from the manufacturer or not approved by the manufacturer.
  • Page 5 Safety instructions for operation years. Possible injuries include damage to the blood circulation system, the nervous system, joints, and other body structures. • Symptoms can occur during operation of the product WARNING: Read the warning instructions or at other times. If you have symptoms and that follow before you use the product.
  • Page 6 Do a check of the safety devices regularly. If the area. safety devices are defective, speak to your Husqvarna service agent. • If it is possible, point the exhaust of the product where it cannot cause dust to go into the air.

  • Page 7: Operation

    by the manufacturer, can cause serious injury or • After maintenance, do a check of the vibration level death. in the product. If it is not correct, speak to an approved service agent. • Replace damaged, worn or broken parts. •...
  • Page 8 Working techniques 2. Connect the power cord to a 3-phase power outlet 400 V, 16 A fuse. The floating operation removes dents on the concrete surface. The concrete surface must be sufficiently hard before the floating operation. The concrete surface is WARNING: Make sure that the power sufficiently hard when a shoe gives only a small recess outlet has RCD protection.
  • Page 9 • To move the product rearward, pull the handle Note: The period of time between troweling operation is rearward. calculated from how quickly the concrete sets. To move the product in different directions • To turn to the left, lift the handle. To adjust the blade angle The blade angle is adjusted gradually.

  • Page 10: Maintenance

    Maintenance Introduction For spare parts, speak to your Husqvarna dealer or service agent. WARNING: Read and understand the safety Maintenance schedule chapter before you do maintenance on the product. * = General maintenance done by the operator. The instructions are not given in this operator's manual.
  • Page 11 To clean or replace the blade shafts To clean or replace the bearing for the pressure plate 1. Remove the nuts and screws from the blade shafts. 1. Remove the screw and washer. 2. Pull the blade shafts from the hub. 2.
  • Page 12 To repair the coupling between the 3. Replace the blades. motor and the gearbox • Make sure that the dimension (A) is between 0.5-1.5 mm/0.02-0.06 in. a) If the blade has wear on 1 edge only, turn the • Make sure that the groove in the connector (B) blade 180 degrees and put it back.

  • Page 13: Troubleshooting

    2. Loosen the locking knobs for the protection ring (A) 3. Tighten the locking knobs for the protection ring. by 8-10 mm/0.31-0.39 in. 4. Make sure that the magnet (B) closes the circuit. 3. Remove the protection ring. a) If the magnet of the magnetic switch is replaced, make sure that there is a clearance of 0-2 mm/ To attach the protection ring 0-0.08 in.

  • Page 14: Transportation, Storage And Disposal

    Problem Cause Solution The blades do not ro- The floating disc is used and the concrete is Let the concrete dry some more before you tate smoothly. too wet. operate the product. The motor is defective. Repair or replace the motor. The transmission is defective.
  • Page 15 • When the product no longer is used, send it to a Husqvarna dealer or discard it at a recycling • Attach the lifting equipment to the lifting eye. location. WARNING: Do not use metal hooks,...

  • Page 16: Technical Data

    Technical data Technical data Motor type 400V-3-50 Hz Motor power, kW 1.6/2.4 Blade speed, rpm 60/120 Rated current, A Type of handle Long Type of blade angle adjustment Twist pitch Type of blade arms Quick release/Bolt on Grease, shaft for blade adjustments Shell Gadus S2 or equivalent Gearbox oil Synthetic Mobil SHC 634...
  • Page 17 Weights and dimensions for options Diameter 850 mm/33.5 in. Diameter 1020 mm/40.2 in. Trowel blade, mm/in. 850/33.5 850/33.5, 915/36, 980/38.6 Protection ring, mm/in. 850/33.5 1020/40.2 Noise and vibration declaration statement These declared values were obtained by laboratory type testing in accordance with the stated directive or standards and are suitable for comparison with the declared values of other products tested in accordance with the same directive or standards.
  • Page 18 Product dimensions (diameter 850 mm/33.5 in.) Handle width, mm/in. 505/19.9 Handle height, mm/in. 950/37.4 Width of blade assembly, Height at blade adjustment 855/33.7 1194/47.0 mm/in. knob, mm/in. Height at lifting point on the Length with handle folded, 842/33.1 1154/45.4 lifting eye, mm/in. mm/in.
  • Page 19 Product dimensions (diameter 1020 mm/40.2 in.) Handle width, mm/in. 505/19.9 Handle height, mm/in. 950/37.4 Width of blade assembly, Height at blade adjustment 1000/39.4 1194/47.0 mm/in. knob, mm/in. Height at lifting point on the Length with handle folded, 842/33.1 1227/48.3 lifting eye, mm/in. mm/in.

  • Page 20: Ec Declaration Of Conformity

    EC Declaration of Conformity EC Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Concrete Smoothing Machine, Trowel Brand Husqvarna Type/Model BG Combi Identification Serial numbers dating from 2019 and onwards...
  • Page 21 1124 - 001 - 06.04.2020...
  • Page 22 1124 - 001 - 06.04.2020...
  • Page 23 1124 - 001 - 06.04.2020...
  • Page 24 www.husqvarnacp.com Original instructions 1140657-26 2020-04-16...