Related Manuals for Sony VPL-VW350ES
Summary of Contents for Sony VPL-VW350ES
- Page 1 4-567-964-01 (1) Video Projector Operating Instructions Before operating the unit, please read this manual and supplied Quick Reference Manual thoroughly and retain them for future reference. VPL-VW350ES...
-
Page 2: Table Of Contents
Table of Contents Location of Controls Using Network Features Front/Right Side ......... 3 Displaying the Control Window of the Unit with a Web Browser ....38 Rear/Left Side/Bottom ....... 4 Operating the Control Window ..39 Remote Control ........5 Switching the Page ......39 Setting the Access Limitation ..39 Connections and Confirming the Information... -
Page 3: Location Of Controls
Location of Controls Front/Right Side Warning indicators Warning indicators Others a ON/STANDBY indicator i Lamp cover (page 47) (page 44) j 3D Sync Transmitter b WARNING indicator (page 44) Located on the inside of the lamp cover. k Ventilation holes (exhaust) Connectors l Ventilation holes (intake) c LAN connector (page 38) -
Page 4: Rear/Left Side/Bottom
Rear/Left Side/Bottom The buttons on the control panel have the same names as those on the remote control. Control panel Control panel Others a ?/1 (ON/STANDBY) button f Remote control detector (page 7) (page 7) b INPUT button (page 13) g Ventilation holes (intake) (page 49) c MENU button (page 20) -
Page 5: Remote Control
a LIGHT button Remote Control Illuminates the buttons on the remote control. b Infrared transmitter c ?/1 (ON/STANDBY) button (page 7) d INPUT button (page 13) e CALIBRATED PRESET buttons (page 19) f PATTERN button (page 8) g RESET button (page 21) h M/m/ -
Page 6: Connections And Preparations
Connections and Preparations This section describes how to install the unit and screen, how to connect the equipment from which you want to project the picture, etc. Note Installing the Unit When using a screen with an uneven surface, stripes pattern may rarely appear on the screen The installation distance between the unit depending on the distance between the screen and a screen varies depending on the size of... -
Page 7: Adjusting The Picture Position
Note Adjusting the Picture Depending on the installation location of the Position unit, you may not be able to control it with the remote control. In this case, point the remote control at the remote control detector of the Project an image on the screen and then unit or the screen. - Page 8 Adjust the focus. Adjust the picture size. Press the PATTERN button repeatedly to Press the PATTERN button repeatedly to display the Lens Focus adjustment display the Lens Zoom adjustment window (test pattern). Then adjust the window (test pattern). Then adjust the focus of the picture by pressing the M/m/ size of the picture by pressing the M/m/
- Page 9 To adjust the horizontal position To adjust the vertical position Press
- Page 10 Range of movement of the projected Lens adjustment window (test picture pattern) 1.78:1 (16:9) 0.85V 1.33:1 (4:3) 0.31H 0.31H Projected Picture 2.35:1 0.8V H: Width of the projected picture V: Height of the projected picture 1.85:1 The dashed lines show the screen sizes of each aspect ratio.
-
Page 11: Connecting To Video Equipment Or A Computer
AV amplifier Speakers to HDMI output HDMI cable (not supplied) : Video signal flow Use a high speed HDMI cable on which the cable type logo is specified. (Sony products are recommended.) Connecting to Video Equipment or a Computer... - Page 12 Notes • Use a high-speed HDMI cable. With a standard HDMI cable, images of 1080p, DeepColor, 3D video and 4K video may not be displayed properly. • When connecting an HDMI cable to the unit, make sure the mark on the upper part of the HDMI input of the unit and the v mark on the connector of the cable is set at the same position.
-
Page 13: Projecting
Projecting This section describes how to operate the unit to view the picture from the equipment connected to the unit. It also describes how to adjust the quality of the picture to suit your taste. Turning Off the Power Projecting the Picture Press the ?/1 (ON/STANDBY) button. -
Page 14: Watching 3D Video Images
Adjusting/Setting the 3D functions Watching 3D Video You can adjust/set the 3D functions by Images pressing the 3D button on the remote control or with the “3D Settings” of the Function menu. For details, see “3D Settings” You can enjoy powerful 3D video images, (page 31). - Page 15 Top or side view Projector 10 m 10 m 10 m 10 m Watching 3D Video Images...
-
Page 16: Selecting The Aspect Ratio According To The Video Signal
Selecting the Aspect Ratio According to the Video Signal You can select an aspect ratio best suited for the video signal received. Press ASPECT. ASPECT Each time you press the button, you can button select the “Aspect” setting.You can also select it using the menu (page 27). - Page 17 Original image Recommended setting and resultant images Normal 1.78:1 (16:9) 1.33:1 (4:3) 1.33:1 (4:3) with side panels V Stretch 2.35:1 When using an anamorphic lens Squeeze 16:9 When using an anamorphic lens Selecting the Aspect Ratio According to the Video Signal...
- Page 18 Original image Recommended setting and resultant images Stretch Squeezed Notes • Selectable aspect modes vary depending on the input signal (page 57). • The aspect cannot be selected for an input signal from a computer, or an input signal with a resolution of 4096 × 2160 (page 52). Notes on switching the “Aspect”...
-
Page 19: Selecting The Picture Viewing Mode
Selecting the Picture Viewing Mode You can select the picture viewing mode that best suits the type of video source or room conditions. You can save and use different preset modes for 2D/3D respectively. CALIBRATED Press one of the CALIBRATED PRESET PRESET buttons buttons. -
Page 20: Using The Menus
Using the Menus This section describes how to make various adjustments and settings using the menus. Operation through the Menus The unit is equipped with an on-screen menu for making various adjustments and settings. If you select an item name followed by an arrow (B), the next menu window with setting items appears. - Page 21 Setting menu To reset the picture that has been adjusted Select “Reset” from the Picture menu. When the screen display appears, select “Yes” using < and press Adjustment menu All of the following settings are reset to its factory preset value: “Reality Creation,”...
-
Page 22: Picture Menu
Picture Menu The Picture menu is used for adjusting the picture. Note These items may not be available, depending on the type of input signal. For details, see “Input Signals and Adjustable/Setting Items” (page 54). Item names in brackets represent those printed on the remote control. Setting items Description Calib. - Page 23 Database: Select “Normal” or “Mastered in 4K.” “Mastered in 4K” provides image quality suitable for Blu-ray Disc™ “Mastered in 4K” releasing from Sony Pictures Home Entertainment. Resolution: When you increase the setting value, the texture and detail of the picture become sharper.
- Page 24 Setting items Description Contrast Adjusts the contrast. [CONTRAST] Higher values increase the sharpness in images, while lower values decrease the sharpness. You can make adjustments by pressing the CONTRAST +/- on the remote control. Brightness Adjusts the brightness of the picture. [BRIGHTNESS] The higher the setting, the brighter the picture.
- Page 25 Setting items Description MPEG NR Reduces block noise and mosquito noise, in particular in digital signals. (MPEG Noise Auto: Detects the noise level to reduce the block noise and mosquito Reduction) noise of the picture automatically. High/Middle/Low: Select a setting according to the block noise and mosquito noise of the input signal source.
- Page 26 Setting items Description x.v.Color Set this item when connecting the unit with equipment that supports x.v.Color and playing back an x.v.Color video signal. On: You can play back an x.v.Color video signal. Off: The “x.v.Color” function is not applied. For details on x.v.Color, see “About the x.v.Color” (page 46). Setting x.v.Color to “On”...
-
Page 27: Screen Menu
Screen Menu You can set the picture size, aspect mode, etc. Note These items may not be available, depending on the type of input signal. For details, see “Input Signals and Adjustable/Setting Items” (page 54). Item names in brackets represent those printed on the remote control. Setting items Description Aspect... - Page 28 Setting items Description Tips • When you select “V Stretch” or “Squeeze,” select the anamorphic lens type from “Anamorphic Lens” in the Installation menu. • Selectable aspect modes vary depending on the input signal (page 57). • The aspect cannot be selected for an input signal from a computer, or an input signal with a resolution of 4096 ×...
-
Page 29: Setup Menu
• To turn on the power with the Remote Start function, a special command should be sent from a PC or a terminal. For details, consult with qualified Sony personnel. Note When Remote Start is set to “On,” the standby power requirement will increase. - Page 30 Setting items Description Network Management On: Set when connected to the network and continuously communicating with the projector control equipment. Note When Network Management is set to “On,” the network function is continuously enabled. Set Network Management to “Off” for normal use.
-
Page 31: Function Menu
Function Menu The Function menu is used for changing the settings of the various functions of the unit. Setting items Description 3D Settings You can change the settings of the 3D function. 2D-3D Display For Switching the video images to “2D” or “3D.” Sel. -
Page 32: Lock
Setting items Description 3D Depth Adjust For adjusting the depth of the 3D video images on the screen. The setting can be made only when a 3D Format other than “Simulated 3D” is selected. Depth Front Normal Depth We recommend that “3D Depth Adjust” be set to “0.” The 3D video images may be difficult to perceive, depending on the setting of “3D Depth Adjust.”... - Page 33 Items Locked by Settings Lock Group 1 Group 2 Picture menu Setup menu Reset Status Reality Creation Language Contrast Enhancer Menu Position Lamp Control Cooling Setting Motionflow Remote Start Contrast Network Management Brightness Lamp Setting Color Function menu Dynamic Range Color Temp.
-
Page 34: Installation Menu
Installation Menu The Installation menu is used for changing the installation settings. Setting items Description Image Flip Flips the picture on the screen horizontally and/or vertically. HV: Flips the picture horizontally and vertically. H: Flips the picture horizontally. V: Flips the picture vertically. Off: The picture does not flip. - Page 35 Setting items Description Blanking This feature allows you to adjust the displayable region within the four directions of the screen. Select the edge to adjust by highlighting Left, Right, Top, or Bottom using the M/m buttons. Adjust the amount of blanking using the
- Page 36 Setting items Description When “Zone” is selected: Select the position to adjust with
-
Page 37: Information Menu
Information Menu The Information menu displays the model name, serial number, input signal type, software version and the cumulated hours of usage of the lamp. Model name Serial No. Signal type Software version Items Description Model Name Displays the model name Serial No. -
Page 38: Using Network Features
Using Network Features Connection to the network allows you to Displaying the operate the following features: • Checking the current status of the unit Control Window of via a Web browser. the Unit with a Web • Making the network settings for the unit. -
Page 39: Operating The Control Window
Operating the Control Window Switching the Page Click one of the Page Switching buttons to display the desired setting page. Once you make the network settings, you can open the Control window only by performing step 3 of this procedure. Page Switching buttons Setting the Access Limitation You can limit a user for accessing any... -
Page 40: Confirming The Information Regarding The Unit
Note If you forget your password, consult with qualified Sony personnel. Confirming the Information Regarding the Unit You can confirm the current settings for the unit on the Information page. Information area Operating the Control Window... -
Page 41: Error Handling
Error Handling Troubleshooting If the unit appears to be operating erratically, try to diagnose and correct the problem using the following instructions. If the problem persists, consult with qualified Sony personnel. Power Symptom Cause and Remedy Page The power is not turned The power may not turn on if you turn the power off with ?/ –... - Page 42 The model name does not The display mode of the unit may be set at the time of – disappear from the purchase. Consult with your local dealer or qualified Sony screen. personnel. Remote control Symptom Cause and Remedy...
- Page 43 3D video images Symptom Cause and Remedy Page The video image does not Check if the 3D glasses are turned on. seem like 3D video Make sure that the battery in the 3D glasses could be weak – images. or is sufficiently charged. Set “2D-3D Display Sel.”...
-
Page 44: Warning Indicators
Sony personnel. (Flashes in red) (Flashes in red) Both indicators flash Note When a warning indicator other than the above starts flashing, and the symptom persists even after carrying out the above methods, consult with qualified Sony personnel. Warning Indicators... -
Page 45: Message Lists
Message Lists Warning messages Symptom Cause and Remedy Page High temp.! Lamp off in Turn off the power. – 1 min. Check to ensure that nothing is blocking the ventilation 3, 4 holes. Frequency is out of Frequency is out of range. Input a signal that is within the range! acceptable frequency range of the unit. -
Page 46: Others
Copy the downloaded xvYCC specifications and is a trademark files to your USB memory, insert the USB of Sony Corporation. memory to the USB terminal of the unit, • xvYCC is an international standard of the then perform the update. -
Page 47: Replacing The Lamp
the specified projector lamp, the unit may Replacing the Lamp malfunction. • Be sure to turn off the unit and unplug the power cord before replacing the lamp, then The lamp used for the light source has a check the ON/STANDBY indicator has certain lifespan. - Page 48 Push in the new lamp by the handle securely until it reaches the end, and then tighten the 3 screws. Loosen the 3 screws on the lamp with the Phillips screwdriver. Hold up the handle, then pull the lamp straight out. Note Be careful not to touch the optical block inside the unit.
- Page 49 Wipe dust off the ventilation holes • The unit will not turn on unless the lamp cover are securely closed. (intake) with a soft cloth. • To clear a message displayed on the screen, press any button either on the remote control or the control panel of the unit once.
-
Page 50: Cleaning
Mettre à disposition de la lampe Cleaning usagée Pour les clients aux États-Unis Cleaning the cabinet La lampe dans ce produit contient du • To remove dust from the cabinet, wipe mercure. La disposition de ces gently with a soft cloth. If dust is matériaux peut être réglementée suite à... -
Page 51: Specifications
Specifications Item Description Display system SXRD panel, projection system Display device Size of effective 0.74-inch (18.8 mm) SXRD display area Number of pixels 26,542,080 pixels (8,847,360 pixels × 3) Projection lens 2.06 times zoom lens (motorized) f = 21.7 mm to 44.7 mm F3.0 to F4.0 Light source Ultra High Pressure Lamp 230 W type... -
Page 52: Preset Signals
• The values for mass and dimensions are approximate. • Not all optional accessories are available in all countries and area. Please check with your local Sony Authorized Dealer. • Information on accessories in this manual is current as of October 2014. - Page 53 Preset Preset signal (resolution) fH (kHz) fV (Hz) Sync memory no. 1920 × 1080/60i 1080/60i 67.500 60.000 – (Frame packing) (1920 × 1080i) 1920 × 1080/50i 1080/50i 56.250 50.000 – (Frame packing) (1920 × 1080i) 3840 × 2160/60p* 3840×2160/60p 135.000 60.000 –...
-
Page 54: Input Signals And Adjustable/Setting Items
Input Signals and Adjustable/Setting Items The items in the menus available to adjust differ depending on the input signal. The following tables indicate them. The items that cannot be adjusted/set are not displayed in the menu. Picture menu Input signal Item Component signal Video GBR signal... -
Page 55: Compatible 3D Signals
Screen menu Input signal Item Component signal Video GBR signal Computer signal Aspect* (excluding preset (excluding preset – memory numbers 76 memory numbers 78, to 79 and 96) 79 and 96) : Adjustable/can be set –: Not adjustable/cannot be set *1: For further details, refer to the tables in “Aspect Mode”... - Page 56 3D signals Item 720/60p, 1080/60i, 1080/24p 1080/60p, 720/50p 1080/50i 1080/50p Film Mode – – – x.v.Color Aspect* : Adjustable/can be set –: Not adjustable/cannot be set *1: The item is not available for Frame Packing/Over-Under on 720/60p, or Over-Under on 1080/ 60p.
-
Page 57: Aspect Mode
Aspect Mode Selectable items vary depending on the type of input signal or 3D format. For details, see the tables below. Items that cannot be selected are not displayed in the menu. 1920 × 1080 720 × 480 Acceptable signals 4096 ×... -
Page 58: Motionflow
Motionflow Selectable items vary depending on the type of input signal or 3D format. For details, see the tables below. Items that cannot be selected are not displayed in the menu. 1920 × 1080 1280 × 720 3840 × 2160 Acceptable signals Others 720 ×... - Page 59 Picture menu Item Storage conditions Calib. Preset For each input connector Reset For each input connector and Calib. Preset Reality Creation Contrast Enhancer Lamp Control Motionflow Contrast Brightness Color Color Temp. D93-D55 Custom 1-5 Gain R For each Color Temp., Custom 1-5 Gain G Gain B Bias R...
-
Page 60: Projection Distance And Lens Shift Range
Projection Distance and Lens Shift Range The projection distance refers to the distance between the front of the lens and the projected surface. Projection distance L Front of the lens Projected image The lens shift range represents the distance in percent (%) by which the lens can be shifted from the center of the projected image. - Page 61 When projecting in 1.90:1 (Native Full Display 17:9) format 1.90 Projection distance Unit: m (inches) Projection image size Projection distance L Diagonal Width × Height 80" (2.03 m) 1.80 × 0.95 (71 × 37) 2.32 – 4.77 (91 – 187) 100"...
- Page 62 When projecting in 1.78:1 (16:9) format 1.78 Video display area Projection area Projection distance Unit: m (inches) Projection image size Projection distance L Diagonal Width × Height 80" (2.03 m) 1.77 × 1.00 (70 × 39) 2.44 – 5.01 (96 – 197) 100"...
- Page 63 When projecting in 2.35:1 format 2.35 Video display area Projection area Projection distance Unit: m (inches) Projection image size Projection distance L Diagonal Width × Height 80" (2.03 m) 1.87 × 0.80 (74 × 31) 2.41 – 4.96 (95 – 195) 100"...
-
Page 64: Dimensions
Dimensions Front Unit: mm (inches) 495.6 (19 247.8 (9 247.8 (9 Center of the lens Bottom Unit: mm (inches) Front of the cabinet 87.3 (3 142.8 (5 150.6 (5 408.9 (16 7.5 ( 463.6 (18 Dimensions... - Page 65 The distance between the front of the lens and the front of the cabinet Unit: mm (inches) 36.8 (1 Front of the lens Front of the cabinet Attaching the PSS-H10 projector suspension support Front view Unit: mm (inches) 150 (5 Ceiling Center of the The bottom...
- Page 66 Side view Unit: mm (inches) 213.5 (8 130 (5 Front of the cabinet 258.5 (10 463.6 (18 Top view Unit: mm (inches) 213.4 (8 130 (5 Front of the cabinet Upper ceiling mount bracket 258.5 (10 Center of the supporting pole (The center of the supporting pole is different from that of the unit.) Dimensions...
-
Page 67: Notices And Licenses For Software Used In This Product
To prevent this, we have made it clear that obtained using the following link: any patent must be licensed for everyone’s free use or http://oss.sony.net/Products/Linux/ not licensed at all. =============================== The precise terms and conditions for copying, distribution and modification follow. - Page 68 translation is included without limitation in the term licensees extend to the entire whole, and thus to each “modification”.) Each licensee is addressed as “you”. and every part regardless of who wrote it. Activities other than copying, distribution and Thus, it is not the intent of this section to claim rights modification are not covered by this License;...
- Page 69 automatically terminate your rights under this This section is intended to make thoroughly clear License. what is believed to be a consequence of the rest of this However, parties who have received copies, or rights, License. 8. If the distribution and/or use of the Program is from you under this License will not have their licenses terminated so long as such parties remain in restricted in certain countries either by patents or by...
- Page 70 OR ANY OTHER PARTY WHO MAY MODIFY Public License. Of course, the commands you use AND/OR REDISTRIBUTE THE PROGRAM AS may be called something other than ‘show w’ and PERMITTED ABOVE, BE LIABLE TO YOU FOR ‘show c’; they could even be mouse-clicks or menu DAMAGES, INCLUDING ANY GENERAL, items--whatever suits your program.
- Page 71 programs; and that you are informed that you can do However, the Lesser license provides advantages in these things. certain special circumstances. To protect your rights, we need to make restrictions For example, on rare occasions, there may be a that forbid distributors to deny you these rights or to special need to encourage the widest possible use of a ask you to surrender these rights.
- Page 72 definition files, plus the scripts used to control the Library, the distribution of the whole must be on compilation and installation of the library. the terms of this License, whose permissions for other Activities other than copying, distribution and licensees extend to the entire whole, and thus to each modification are not covered by this License;...
- Page 73 When a “work that uses the Library” uses material version is interface-compatible with the version that from a header file that is part of the Library, the object the work was made with. code for the work may be a derivative work of the c) Accompany the work with a written offer, valid for Library even though the source code is not.
- Page 74 13. The Free Software Foundation may publish modifying or distributing the Library (or any work based on the Library), you indicate your acceptance revised and/or new versions of the Lesser General of this License to do so, and all its terms and Public License from time to time.
- Page 75 1. Redistributions of source code must retain the LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR above copyright notice, this list of conditions and the OTHER PARTY HAS BEEN ADVISED OF THE following disclaimer. 2. Redistributions in binary form must reproduce the POSSIBILITY OF SUCH DAMAGES.
- Page 76 This product includes software developed by Danga PROFITS; OR BUSINESS INTERRUPTION) Interactive, Inc. HOWEVER CAUSED AND ON ANY THEORY OF =============================== LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING INDEPENDENT JPEG GROUP NEGLIGENCE OR OTHERWISE) ARISING IN SOFTWARE ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE This software is based in part on the work of the POSSIBILITY OF SUCH DAMAGE.
- Page 77 THIS SOFTWARE IS PROVIDED BY ERIC THE SOFTWARE IS PROVIDED “AS IS”, YOUNG “AS IS’’ AND ANY EXPRESS OR WITHOUT WARRANTY OF ANY KIND, IMPLIED WARRANTIES, INCLUDING, BUT EXPRESS OR IMPLIED, INCLUDING BUT NOT NOT LIMITED TO, THE IMPLIED WARRANTIES LIMITED TO THE WARRANTIES OF OF MERCHANTABILITY AND FITNESS FOR A MERCHANTABILITY, FITNESS FOR A...
- Page 78 Redistributions of source code must retain the above This material is reproduced with permission from copyright notice, this list of conditions and the American National Standards Committee X3, on following disclaimer. Information Processing Systems. Computer and Redistributions in binary form must reproduce the Business Equipment Manufacturers Association above copyright notice, this list of conditions and the (CBEMA), 311 First St., NW, Suite 500, Washington,...
- Page 79 Except as contained in this notice, the name of a following disclaimer in the documentation and/or copyright holder shall not be used in advertising or other materials provided with the distribution. otherwise to promote the sale, use or other dealings in 3.
- Page 80 granted, provided that the above copyright notice and All of the code can be freely used and redistributed. this permission notice appear in all copies. The individual source files each have their own THE SOFTWARE IS PROVIDED “AS IS” AND copyright and permission notice.
- Page 81 NO EVENT SHALL THE AUTHOR(S) BE LIABLE SOFTWARE, EVEN IF ADVISED OF THE FOR ANY DIRECT, INDIRECT, INCIDENTAL, POSSIBILITY OF SUCH DAMAGE. SPECIAL, EXEMPLARY, OR CONSEQUENTIAL =============================== DAMAGES (INCLUDING, BUT NOT LIMITED pcre TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PCRE LICENCE PROFITS;...
- Page 82 PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;...
-
Page 83: Index
Connectors ..........3 Index Contrast ........... 24 Contrast Enhancer ........23 Control panel ..........4 Numerics Cooling Setting ........29 3D glasses 3D glasses communication range ..14 Using the 3D glasses ......14 Dimensions ..........64 3D Settings Dynamic Range ........32 2D-3D Display Sel. - Page 84 Trademark Information Remote control detector ......3, 4 • “PlayStation” is a registered trademark Remote Start ..........29 of Sony Computer Entertainment Inc. Replacing the lamp ......... 47 • The terms HDMI and HDMI High- Reset ............23 Definition Multimedia Interface, and the Resetting the items ........
- Page 85 © 2014 Sony Corporation...