Table of Contents
Quick Links
Table of Contents
Related Manuals for Beko METPOINT FLM SF13
Summary of Contents for Beko METPOINT FLM SF13
- Page 1 EN - English Installation and operating manual Thermal flow meter METPOINT FLM SF13 ® FLMSF13LD8 | FLMSF13DD8 | FLMSF13LD15 | FLMSF13DD15 | FLMSF13LD20 | FLMSF13DD20 | FLMSF13LD25 | FLMSF13DD25 | FLMSF13LD32 | FLMSF13DD32 | FLMSF13LD40 | FLMSF13DD40 | FLMSF13LD50 | FLMSF13DD50...
-
Page 2: Table Of Contents
Installation and operating manual Content 1. Safety information ............................4 1.1. Pictograms and symbols .......................... 4 1.1.1. In this documentation ................................4 1.1.2. On the device ..................................4 1.2. Signal words ............................4 1.3. Safety instructions ..........................5 1.4. Transport and storage ..........................6 1.5. - Page 3 Installation and operating manual 5. Start-up ................................ 24 6. Configuration and operation ......................... 24 6.1. Display during operation ........................24 6.2. Setup menu ............................25 6.3. Sensor Setup ............................25 6.3.1. Entering pipe inside diameter ............................26 6.3.2. Entering / changing consumption counter value ..................... 26 6.3.3.
-
Page 4: Safety Information
Installation and operating manual 1. Safety information 1.1. Pictograms and symbols 1.1.1. In this documentation General instructions Observe installation and operating instructions General hazard symbol (danger, warning, caution) General hazard symbol (danger, warning, caution) relating to mains voltage and powered machine parts 1.1.2. -
Page 5: Safety Instructions
Installation and operating manual 1.3. Safety instructions DANGER Escaping compressed gas Risk of serious or even fatal injury from contact with escaping compressed gas or from unsecured plant components. • Before carrying out any assembly, installation or maintenance work, depressurise the system. All above work must be carried out by authorised specialist technical personnel •... -
Page 6: Transport And Storage
Despite our best efforts regarding packaging, etc., the device might be damaged during transport. Upon delivery, please remove all packaging material and inspect the device for visible damage. If you detect such damage, immediately notify the carrier company and BEKO TECHNOLOGIES GMBH or one of its agents. CAUTION... -
Page 7: Intended Use
FLM is primarily used in compressed air systems. On request, the sensor can be programmed by ® BEKO TECHNOLOGIES GmbH for the measurement of other gases: nitrogen • The device is not suitable for operation in potentially explosive or aggressive atmospheres. -
Page 8: Product Information
Installation and operating manual 2. Product information 2.1. Scope of delivery The table below shows the scope of delivery of the METPOINT FLM. ® Designation Picture Calibration certificate Connecting cable (5-wire) 2.2. Type plate The type plate is attached to the device housing. It contains all relevant technical data of the METPOINT FLM. -
Page 9: Product Overview And Description
Installation and operating manual 2.3. Product overview and description 2.3.1. Identification based on product code Rated diameter of measuring section (R) Version with LED Interface: RS485 Operating pressure: 16 bar SensorFlow (model designation) FlowMeasurement (product designation) METPOINT SF13 ®... -
Page 10: Product Description
Installation and operating manual 2.3.2. Product description The METPOINT FLM thermal flow meter measures the volume flow, which forms the basis for intelligent energy management. ® It can be used to identify potential savings, overloads and weak points in a system to improve its efficiency. By measuring the actual flow to the various production units, operators are in a position to make decisions based on facts. -
Page 11: Control And Display Elements
Installation and operating manual 2.4. Control and display elements 2.4.1. Version with display METPOIN T F LM ® Plug-type connector A FLOW MEASURING 395,38 160515 Plug-type connector B HW:1.00 SW:1.00 NOTICE Additional information For more information regarding the operation of the device, see „Configuration and operation“ auf Seite 2.4.2. -
Page 12: Direction Of Flow
Installation and operating manual 2.4.3. Direction of flow The direction of flow is indicated by the arrows (1) on the housing of the METPOINT FLM and on the sensor tube. ® NOTICE Additional information If necessary, turn the housing (e.g. to change the direction of flow through the device). For more information, see „Turning housing“... -
Page 13: Dimensions
Installation and operating manual 2.5. Dimensions SW 36 SW 36 Dimensions Version with display Version with LED G ½" (ISO 228/1) C (mm) F (mm) G (mm) 105.5 Measuring section dimensions DN15 DN20 DN25 DN32 DN40 DN50 R¼" R½" R¾" R1"... -
Page 14: Technical Data
Installation and operating manual 2.6. Technical data Technical data SF13 Max. operating pressure 16 bar Measuring technique Calorimetric Operating temperature Sensor tube and fittings: -30 ... +140 °C Housing: -30 ... +80 °C Measured parameters m³/h (factory settings) On the display version, the following units can be chosen: m³/min, l/min, l/s, ft/min, cfm, m/s, kg/min, kg/s Sensor Pt45, Pt1000... -
Page 15: Measuring Ranges
Installation and operating manual 2.7. Measuring ranges 2.7.1. For air Pipe inside Ø Pipe size Rated diameter SF13 Consumption Inch Measuring range from ... to Default settings ¼ 0.8 ... 90 l/min ½ 16.1 DN15 0.2 ... 90 m³/h m³ ¾... -
Page 16: Installation
Installation and operating manual 3. Installation 3.1. Warning DANGER Escaping compressed gas Risk of serious or even fatal injury from contact with escaping compressed gas or from unsecured plant components. • Before carrying out any assembly, installation or maintenance work, depressurise the system. Such work must be carried out by authorised specialist technical personnel only (see „Safety instructions“... -
Page 17: Turning Housing
Installation and operating manual 3.1.3. Turning housing If required by the flow direction, the housing can be turned by 180° by loosening the 4 setscrews with 1.5mm hexagon sockets. Align the housing as required and tighten the setscrews again by hand. NOTICE Risk of damage to device Ensure that the connecting pipes are correctly mounted and that the gaskets are installed properly. -
Page 18: Electrical Installation
Installation and operating manual 4. Electrical installation 4.1. Pin assignment of plug-type connectors Pin assignment of plug-type connector A, M12 x 1, 5-pin, A-coded (according to EN 61076-2-101) Pin assignment of connector Pin assignment of connector Pin assignment of connector Transmitter side Socket side Screw side... -
Page 19: Current Output 4
Installation and operating manual 4.2.2. Current output 4 ... 20 mA, 3-wire Connection by means of plug-type connector A. Connection diagram for METPOINT SF13 ® 4 ... 20 mA 4 ... 20 mA Pin assignment - sensor Function Wire colour PIN-1 Plus (+) connection, power supply brown... -
Page 20: Galvanically Isolated Pulse Output
Installation and operating manual 4.2.4. Galvanically isolated pulse output Connection by means of plug-type connector B. Connection diagram for METPOINT SF13 ® Impuls Impuls Pin assignment - sensor Function Wire colour PIN-1 not assigned brown PIN-2 not assigned white PIN-3 not assigned blue PIN-4... -
Page 21: Current Output 4
Installation and operating manual 4.3.2. Current output 4 ... 20 mA, 3-wire Connection by means of plug-type connector A. Connection diagram for METPOINT SF13 and METPOINT ® ® BROWN GREY BLUE 4 ... 20 mA Pin assignment - sensor Function Wire colour Pin assignment - BDL PIN-1... -
Page 22: Connection To Metpoint ® Bdl Compact
Installation and operating manual 4.4. Connection to METPOINT BDL compact ® 4.4.1. Bidirectional RS485 bus system Connection by means of plug-type connector A. Connection diagram for METPOINT SF13 and METPOINT BDL compact (digital board) ® ® BROWN BLUE WHITE BLACK RS485 Pin assignment - sensor Function... -
Page 23: Galvanically Isolated Pulse Output
Installation and operating manual 4.4.3. Galvanically isolated pulse output Connection by means of plug-type connector B. Connection diagram for METPOINT SF13 and METPOINT BDL compact (analog board) ® ® BROWN BLACK GREY Impuls BLUE Pin assignment - sensor Function Wire colour Pin assignment - BDL compact PIN-1 not assigned... -
Page 24: Start-Up
Installation and operating manual 5. Start-up To start the METPOINT FLM, power it and perform the sensor setup as described in „Sensor Setup“ auf Seite 25. Slowly ® pressurise the pipes. 6. Configuration and operation When the METPOINT FLM is powered, it is automatically initialised. After this step is completed, the main menu is displayed. ®... -
Page 25: Setup Menu
Installation and operating manual 6.2. Setup menu Press the >>ENTER<< button to call up the setup menu. The setup menu is password-protected. Default password (factory settings): 0000 (4 x zero). If required, change the password by selecting Setup→User Setup→Password Press the >>UP<< button to select and to change a value. Press the >>ENTER<<... -
Page 26: Entering Pipe Inside Diameter
Installation and operating manual 6.3.1. Entering pipe inside diameter Setup → Sensor Setup → Diameter To change the unit, press the >>UP<< button to select the "Unit" field and confirm by pressing the >>ENTER<< button. Press the >>UP<< button to select the desired unit and confirm by pressing the >>ENTER<<... -
Page 27: Selecting Units For Consumption, Flow, Temperature And Pressure
Installation and operating manual 6.3.3. Selecting units for consumption, flow, temperature and pressure Setup → Sensor Setup → Units To change the unit, press the >>UP<< button to select the "Unit" field and confirm by pressing the >>ENTER<< button. If there are more possible units that fit on the screen, press the "<<"... -
Page 28: Entering Reference Conditions
Installation and operating manual 6.3.4. Entering reference conditions Setup → Sensor Setup → Ext. Setup Enter the reference parameter values. Filtertime Setup → Sensor Setup → Ext. Setup → Ref. Pres To change the reference pressure, press the >>UP<< button to select the "Unit"... -
Page 29: Setting Zero Point For Low-Flow Cut-Off Function
Installation and operating manual 6.3.5. Setting zero point for low-flow cut-off function Setup → Sensor Setup → ZP Adjust Enter the zero point and the low-flow cut-off point. Setup → Sensor Setup → ZP Adjust → ZeroPnt If the installed sensor shows a flow rate of > 0 m³/h even if there is no flow, you can enter a zero point for the characteristic. -
Page 30: Modbus Setup
Installation and operating manual 6.4. ModBus setup The METPOINT FLM thermal flow meter is equipped with a RS485 interface (ModBus RTU). Before starting the sensor, configure ® the communication parameters • ModBus ID, baud rate, parity and stop bit to enable communication with the ModBus master. Setup →... -
Page 31: Modbus Settings (2001
Installation and operating manual 6.4.1. ModBus settings (2001 ... 2005) ModBus Register Read/ Byte Data type Description Default Unit/comment register address write 2001 2000 UInt16 ModBus ID ModBus ID 1…247 0 = 1200 1 = 2400 2 = 4800 2002 2001 UInt16 Baud rate... -
Page 32: Pulse / Alarm
Installation and operating manual 6.5. Pulse / alarm Setup → Pulse/Alarm The galvanically isolated pulse output can be used as a pulse or as an alarm output. The following units can be selected for the alarm output: • kg/min, cfm, l/s, m³/h, m/s, °F, °C, kg/s Press "Value"... -
Page 33: User Setup
Installation and operating manual 6.6. User Setup Setup → User Setup On the user setup screen, you can change the password, rotate the display and adjust its brightness. • Password = change password • Backlight = adjust brightness • Rotate = rotate display To change the password, you must enter the new password twice. - Page 34 Installation and operating manual 6.8. 4 ... 20 mA Setup → 4 - 20 mA On this screen, you can adjust the settings for the 4 ... 20 mA current output. Setup → 4 - 20 mA → Channel 1 The following measurements can be configured: •...
-
Page 35: Info
Installation and operating manual Setup → 4 - 20 mA → Error Current On this screen, you can enter the error signal to be sent by the current output in the event of a fault. • 2 mA = sensor fault / system error •... -
Page 36: Spare Parts And Accessories
10. Calibration If the device is not custom-configured, we recommend having it calibrated every 12 months. For calibration, send the METPOINT ® FLM to BEKO TECHNOLOGIES GmbH. 11. LED indicator The METPOINT FLM features a LED calibration indicator mounted at the top of the housing. After 15 months, the LED begins to ®... -
Page 37: Declaration Of Conformity
Installation and operating manual 12. Declaration of Conformity METPOINT SF13 ®... - Page 38 Installation and operating manual BEKO TECHNOLOGIES GMBH Im Taubental 7 41468 Neuss, GERMANY Phone: +49 2131 988-0 www.beko-technologies.com EU Declaration of Conformity We hereby declare that the products named below comply with the stipulations of the relevant directives and technical standards. This declaration only refers to products in the condition in which they have been placed into circulation.
- Page 39 Installation and operating manual METPOINT SF13 ®...
- Page 40 Tel. +81 44 328 76 01 [email protected] [email protected] BEKO TECHNOLOGIES S. de R.L. de C. BEKO TECHNOLOGIES CORP. BEKO Technologies, S de R.L. de C.V. 900 Great Southwest Pkwy SW Blvd. Vito Alessio Robles 4602 Bodega 10 US - Atlanta, GA 30336 Zona Industrial Tel.