Related Manuals for Fujitsu CELSIUS H7510
Summary of Contents for Fujitsu CELSIUS H7510
-
Page 1: Table Of Contents
Removing the USB / audio sub board Removing the sub board switch Removing the display Removing the LCD front cover assy Removing the LCD panel Removing the LCD hinges Removing the webcam Spare parts Celsius H7510 Disposal information for recycling companies Page 1 of 52... -
Page 2: System Expansions And Repairs Document
System expansions and repairs document We recommend printing out the relevant sections of this chapter prior to installation as the device for installing/removing hardware components needs to be switched off. The following illustrations may differ from your device, depending on its configuration and features. If you have received any further documents with your device, you should read these through carefully. -
Page 3: Information On The Installation And Removal Of Components
Information on the installation and removal of components Please pay attention to the locking mechanism (indentations and centring pins) when installing hardware components. Note that some components on the mainboard may be very hot if the device was in use shortly before the case was removed. Utmost care is required during installation and removal to avoid damaging components. -
Page 4: Screws
Screws Screw: M2XL4 Screwdriver: Phillips PH00 Screw: M2.5XL6 (D4.5) Screwdriver: Phillips PH00 Screw: M2XL2.5 Screwdriver: Phillips PH00 Return to Table of Contents Page 4 of 52... -
Page 5: Tools
Tools Screwdriver: Phillips PH00 Plastic tool Plastic tool Return to Table of Contents Page 5 of 52... -
Page 6: Removing The Battery
Removing the battery Required work steps: Required tools: ■ none ■ None ► Close the display. ► Disconnect the mains plug from the mains outlet. ► Disconnect all the cables that are connected to the notebook. ► Turn your notebook over and place it on a stable and flat surface. If necessary, place a non-slip cloth on the surface to avoid scratching the notebook. -
Page 7: Removing The Memories Under The Service Door
Removing the memories under the service door Required work steps: Required tools: ■ Screwdriver: Phillips PH00 ■ Removing the battery ► Remove the screw M2.5XL6 (yellow arrow). ► Lift the memory door in the direction indicated by the green arrow and remove it. Page 7 of 52... - Page 8 ► Release the locks and push them sideways (yellow arrows). ► Remove the memory in the direction indicated by the arrow (green arrows). Return to Table of Contents Page 8 of 52...
-
Page 9: Inserting The Memories Under The Service Door
Inserting the memories under the service door Required work steps: Required tools: ■ Screwdriver: Phillips PH00 ■ Removing the battery ► Remove the screw M2.5XL6 (yellow arrow). ► Lift the memory door in the direction indicated by the green arrow and remove it. Note the coding of the memory Page 9 of 52... - Page 10 ► Carefully place the memory into the socket (green arrow). ► Carefully press on the memory (yellow arrows) until the lock engages on both sides. The same memory type must be inserted into all four slots. Return to Table of Contents Page 10 of 52...
-
Page 11: Removing The Service Door
Removing the service door Required work steps: Required tools: ■ Screwdriver: Phillips PH00 ■ Removing the battery ► Remove the screw M2.5XL6 (yellow circles). ► Lift the service door in the direction indicated by the green arrows. Return to Table of Contents Page 11 of 52... -
Page 12: Removing The M.2 Module Under The Service Door
Removing the M.2 module under the service door Required work steps: Required tools: ■ Screwdriver: Phillips PH00 ■ Removing the battery ■ Removing the service door ► Remove the screw M2XL3 (yellow arrow). ► Lift the M.2 module (green arrow) and remove it from the socket in the direction indicated by the blue arrow. Return to Table of Contents Page 12 of 52... -
Page 13: Inserting The M.2 Module Under The Service Door
Inserting the M.2 module under the service door Required work steps: Required tools: ■ Screwdriver: Phillips PH00 ■ Removing the battery ■ Removing the service door ► Insert the M.2 module into the socket in the direction indicated by the yellow arrow and carefully press it on the other side. Observe the coding. -
Page 14: Removing The 2.5" Hdd
Removing the 2.5” HDD Required work steps: Required tools: ■ none ■ Removing the battery ■ Removing the service door ► Open the connector lock (green arrow) upwards and remove the flexprint cable. ► Lift the HDD from the casing in the direction indicated by the yellow arrow. Return to Table of Contents Page 14 of 52... -
Page 15: Inserting The 2.5" Hdd
Inserting the 2.5” HDD Required work steps: Required tools: ■ none ■ Removing the battery ■ Removing the service door ► Attach the HDD rubbers to the hard disk (yellow arrows). ► Attach the HDD flexprint cable to the hard disk (green arrow). Observe the coding of the plug-in connections for the HDD and cable. - Page 16 ► Insert the hard disk. ► Insert the flexprint cable into the intended plug and close the connector lock (green arrow). Return to Table of Contents Page 16 of 52...
-
Page 17: Mandatory Support Bulletins For Disassembly
Mandatory Support Bulletins for Disassembly SB-M-10030 Minimum requirements to properly finalise hardware repairs on mobile systems SB-M-15007 WIN8x & WIN10 - Spare product key for repaired devices For any information about ESD, please refer to the web-based training course “ESD in electronics“... -
Page 18: Removing The Lte Module
Removing the LTE module Required work steps: Required tools: ■ Removing the battery ■ Screwdriver: Phillips PH00 ■ Removing the service door ► Remove both LTE antennas (yellow arrows). ► Remove the screw M2XL3 (yellow circle). ► Remove the LTE module from the socket in the direction indicated by the green arrow. Return to Table of Contents Page 18 of 52... -
Page 19: Removing The Wlan Module
Removing the WLAN module Required work steps: Required tools: ■ Removing the battery ■ Screwdriver: Phillips PH00 ■ Removing the service door ► Remove the two WLAN antennas (yellow circle). ► Remove the screw M2XL3 (yellow arrow). ► Remove the WLAN module from the socket in the direction indicated by the green arrow. Return to Table of Contents Page 19 of 52... -
Page 20: Removing The Fan
Removing the fan Required work steps: Required tools: ■ Screwdriver: Phillips PH00 ■ Removing the battery ■ Removing the service door ► Remove the three screws M2.5XL6 (yellow circles). ► Remove the fan cable (yellow arrows) from the mainboard. ► Remove the cable from the mainboard (blue arrow) and disconnect it. -
Page 21: Removing The Keyboard
Removing the keyboard Required work steps: Required tools: ■ Screwdriver: Phillips PH00 ■ Removing the battery ■ Plastic tool ■ Removing the service door ■ Removing the fan ► Remove the four M2.5XL6 screws (yellow circles). ► Place the opened notebook on its side and carefully press on the openings against the underside of the keyboard to release the keyboard from the casing. - Page 22 ► Carefully remove the keyboard (green arrows) and slide it upwards in order to reach the flexprint cable. ► Open the connector lock (green arrow) upwards to remove the keyboard cable. ► Remove the keyboard. Return to Table of Contents Page 22 of 52...
-
Page 23: Removing The Memories Under The Keyboard
Removing the memories under the keyboard Required work steps: Required tools: ■ none ■ Removing the battery ■ Removing the service door ■ Removing the fan ■ Removing the keyboard ► Release the locks and push them sideways (yellow arrows). ►... -
Page 24: Removing The M.2 Module Under The Keyboard
Removing the M.2 module under the keyboard Required work steps: Required tools: ■ Screwdriver: Phillips PH00 ■ Removing the battery ■ Removing the service door ■ Removing the fan ■ Removing the keyboard ► Remove the screw M2XL3 (yellow arrow). ►... -
Page 25: Removing The Lower Assy
Removing the lower assy Required work steps: Required tools: ■ Screwdriver: Phillips PH00 ■ Removing the battery ■ Plastic tool ■ Removing the service door ■ Removing the 2.5” HDD ■ Removing the LTE module ■ Removing the WLAN module ►... -
Page 26: Removing The Smartcard Sub Board
Removing the SmartCard sub board Required work steps: Required tools: ■ none ■ Removing the battery ■ Removing the service door ■ Removing the 2.5” HDD ■ Removing the LTE module ■ Removing the WLAN module ■ Removing the lower assy ►... -
Page 27: Removing The Tpm Module (Nation Z)
Removing the TPM module (Nation Z) Required work steps: Required tools: ■ none ■ Removing the battery ■ Removing the service door ■ Removing the 2.5” HDD ■ Removing the LTE module ■ Removing the WLAN module ■ Removing the lower assy ►... -
Page 28: Removing The Touchpad Buttons Sub Board
Removing the touchpad buttons sub board Required work steps: Required tools: ■ Screwdriver: Phillips PH00 ■ Removing the battery ■ Removing the service door ■ Removing the 2.5” HDD ■ Removing the LTE module ■ Removing the WLAN module ■ Removing the lower assy ►... -
Page 29: Removing The Palm Vein/Fingerprint Sensor Sub Board
Removing the palm vein/fingerprint sensor sub board Required work steps: Required tools: ■ Screwdriver: Phillips PH00 ■ Removing the battery ■ Removing the service door ■ Removing the 2.5” HDD ■ Removing the LTE module ■ Removing the WLAN module ■... - Page 30 ► Open the connector lock (green arrow) upwards and remove the flexprint cable. ► Remove the sub board (blue arrow). The frame in which the sub board is located has been adjusted for the respective sensor. Frame for fingerprint sensor Frame for palm vein sensor Return to Table of Contents Page 30 of 52...
-
Page 31: Removing The Dc-In Connector
Removing the DC-in connector Required work steps: Required tools: ■ Screwdriver: Phillips PH00 ■ Removing the battery ■ Removing the service door ■ Removing the 2.5” HDD ■ Removing the LTE module ■ Removing the WLAN module ■ Removing the lower assy ►... - Page 32 ► Remove the plug from the mainboard (yellow arrow) and remove the cable. Return to Table of Contents Page 32 of 52...
-
Page 33: Removing The Mainboard
Removing the mainboard Required work steps: Required tools: ■ Screwdriver: Phillips PH00 ■ Removing the battery ■ Removing the service door ■ Removing the memories under the service door ■ Removing the 2.5” HDD ■ Removing the LTE module ■ Removing the WLAN module ■... -
Page 34: Removing The Usb / Audio Sub Board
Removing the USB / audio sub board Required work steps: Required tools: ■ none ■ Removing the battery ■ Removing the service door ■ Removing the fan ■ Removing the keyboard ■ Removing the M.2 module under the keyboard ■ Removing the 2.5”... - Page 35 ► Open the connector lock (green arrow) upwards and remove the flexprint cable. ► Remove the speaker cable (blue arrow) from the sub board. ► Carefully press the plastic latches in the direction indicated by the yellow arrow and remove the sub board (orange arrow). Return to Table of Contents Page 35 of 52...
-
Page 36: Removing The Sub Board Switch
Removing the sub board switch Required work steps: Required tools: ■ Screwdriver: Phillips PH00 ■ Removing the battery ■ Removing the service door ■ Removing the fan ■ Removing the 2.5” HDD ■ Removing the LTE module ■ Removing the WLAN module ■... - Page 37 ► Remove the screw M2XL4 (yellow circle). ► Carefully press the plastic latches in the direction indicated by the yellow arrow and remove the sub board (green arrow). Return to Table of Contents Page 37 of 52...
-
Page 38: Removing The Display
Removing the display Required work steps: Required tools: ■ Screwdriver: Phillips PH00 ■ Removing the battery ■ the service door Removing ■ Removing the fan ■ Removing the keyboard ■ Removing the M.2 module under the keyboard ■ Removing the 2.5” HDD ■... -
Page 39: Removing The Lcd Front Cover Assy
Removing the LCD front cover assy Required work steps: Required tools: ■ Plastic tool ■ Removing the battery ■ Removing the service door ■ Removing the fan ■ Removing the keyboard ■ Removing the M.2 module under the keyboard ■ Removing the 2.5”... - Page 40 ► Use the plastic tool to open the display frame. ► Carefully use a plastic tool to loosen the plastic latches in the direction indicated by the yellow arrows to disconnect the LCD back cover assy from the LCD front cover assy. Return to Table of Contents Page 40 of 52...
-
Page 41: Removing The Lcd Panel
Removing the LCD panel Required work steps: Required tools: ■ Screwdriver: Phillips PH00 ■ Removing the battery ■ Removing the service door ■ Removing the fan ■ Removing the keyboard ■ Removing the M.2 module of the keyboard ■ Removing the 2.5” HDD ■... - Page 42 ► Remove both adhesive tapes (metal and transparent) and remove the plug from the LCD panel in the direction indicated by the arrow. Return to Table of Contents Page 42 of 52...
-
Page 43: Removing The Lcd Hinges
Removing the LCD hinges Required work steps: Required tools: ■ Screwdriver: Phillips PH00 ■ Removing the battery ■ Removing the service door ■ Removing the fan ■ Removing the keyboard ■ Removing the M.2 module under the keyboard ■ Removing the 2.5” HDD ■... -
Page 44: Removing The Webcam
Removing the webcam Required work steps: Required tools: ■ Screwdriver: Phillips PH00 ■ Removing the battery ■ Removing the service door ■ Removing the fan ■ Removing the keyboard ■ Removing the M.2 module under the service door ■ Removing the 2.5” HDD ■... - Page 45 ► Remove the plug (yellow arrow) from the webcam. ► Attach the plastic tool as shown and detach the webcam carefully. Caution: It is attached very firmly. Return to Table of Contents Page 45 of 52...
-
Page 46: Spare Parts Celsius H7510
Spare parts Celsius H7510 replaceable parts Pos. Spare part Internal spare part name Mechanical parts: Cover (service) lower assy Lower housing upper assy Upper housing LCD back cover assy LCD back cover LCD front cover LCD front frame Hinges HDD rubber... - Page 47 Page 47 of 52...
- Page 48 Page 48 of 52...
- Page 49 Page 49 of 52...
- Page 50 Page 50 of 52...
-
Page 51: Disposal Information For Recycling Companies
Disposal information for recycling companies These instructions are for the complete dismantling of a Fujitsu product. All materials can thereby be disposed of according to their provision in the EC directive 2012/19/EC (Waste Electrical and Electronic Equipment (WEEE)). Product group:... - Page 52 Page 52 of 52...