Fujitsu F2MC-8FX Series Application Note
8-bit microcontroller
Hide thumbs
Also See for F2MC-8FX Series:
- User manual (110 pages) ,
- Application note (53 pages) ,
- Setup manual (30 pages)
Related Manuals for Fujitsu F2MC-8FX Series
Summary of Contents for Fujitsu F2MC-8FX Series
- Page 1 Fujitsu Semiconductor (Shanghai) Co., Ltd. MCU-AN-500047-E-10 Application Note F²MC-8FX FAMILY 8-BIT MICROCONTROLLER MB95200 SERIES TOUCH SENSOR IC ATA2508 DEMONSTRATION SET APPLICATION NOTE...
-
Page 2: Revision History
To obtain up-to-date information and/or specifications, contact your Fujitsu sales representative or Fujitsu authorized dealer. 2. Fujitsu will not be liable for infringement of copyright, industrial property right, or other rights of a third party caused by the use of information or drawings described in this manual. -
Page 3: Table Of Contents
TSC Demo V1.0 Contents CONTENTS REVISION HISTORY ......................2 CONTENTS ..........................2 1 INTRODUCTION ........................ 4 2 APPLICATION ENVIRONMENT ..................5 2.1 TSC Demo Platform ....................5 2.2 TSC Tuning Platform ....................6 3 TSC DEMO FUNCTIONS ....................7 3.1 Demo System Build-up ..................... 7 3.2 ... -
Page 4: 1 Introduction
TSC Demo V1.0 Chapter 1 Introduction 1 Introduction Fujitsu ATA2508 digital touch sensor demo set allows the easy evaluation of touch sensor IC ATA2508 and using Fujitsu MB95200 serial MCU to control this IC. It consists of the below components... -
Page 5: 2 Application Environment
TSC Demo V1.0 Chapter 2 Application Environment 2 Application Environment This chapter introduces demo and tuning environments. 2.1 TSC Demo Platform TSC demo system consists of MB95200 evaluation board, TSC demo board and normal IDC10 cable. This demo system shows MB95F204K MCU controlling TSC ATA2508 and 3 kinds of touch sensor modes. -
Page 6: Tsc Tuning Platform
TSC Demo V1.0 Chapter 2 Application Environment 2.2 TSC Tuning Platform TSC tuning platform consists of AtLab tuning tools, TSC demo board and the special IDC10 cable. AtLab tuning tools and PC S/W support tuning TSC parameter. Refer to “ATA2508 Users Manual V1.4 (EN) v01” for the detailed tuning method. Figure 2-2: TSC Tuning Platform MCU-AN-500047-E-10 –... -
Page 7: 3 Tsc Demo Functions
TSC Demo V1.0 Chapter 3 TSC Demo Functions 3 TSC Demo Functions This chapter introduces TSC demo system usage and functions. 3.1 Demo System Build-up Program TSC demo code “TSC_LPC_1V0” on MB95200 EV-board and set this EV-board into “normal run” mode. Then connect EV-board and TSC demo through IDC10 cable. Figure 3-1: Demo System Build-up 3.2 IDC 10 Pin Assignment Figure 3-2: IDC10 Pin Assignment... -
Page 8: Demo System Power-On
TSC Demo V1.0 Chapter 3 TSC Demo Functions 3.3 Demo System Power-on Provide power to EV-board will power on the whole TSC demo system. MB95200 EV-board supports the below 3 power provided method. 4-pcs batteries 9V DC power supplier USB cable After power on, LED5 on EV-board is light to indicate power-on status and LED2 on EV- board winks to indicate TSC demo code running. -
Page 9: Apis (Adjacent Pattern Interference Suppression) Modes
TSC Demo V1.0 Chapter 3 TSC Demo Functions 3.4 APIS (Adjacent Pattern Interference Suppression) Modes This demo system can support the three kinds of APIS mode. APIS mode I: reports the strongest output only. APIS mode II: reports all outputs to overcome the value of Strength Threshold Register APIS mode III: reports two strongest outputs for multi-touch application Figure 3-4: APIS Mode I MCU-AN-500047-E-10 –... - Page 10 TSC Demo V1.0 Chapter 3 TSC Demo Functions Figure 3-5: APIS Mode II MCU-AN-500047-E-10 – Page 10...
- Page 11 TSC Demo V1.0 Chapter 3 TSC Demo Functions Figure 3-6: APIS mode III MCU-AN-500047-E-10 – Page 11...
- Page 12 TSC Demo V1.0 Chapter 3 TSC Demo Functions Press S1 to change these 3 modes in turn. Figure 3-7: APIS Modes Change MCU-AN-500047-E-10 – Page 12...
-
Page 13: Demo Functions
TSC Demo V1.0 Chapter 3 TSC Demo Functions 3.5 Demo Functions The system supports the demo functions using the buzzer on MB95200 EV-board. The functions are shown briefly on the below figure. Figure 3-8: Demo Functions MCU-AN-500047-E-10 – Page 13... -
Page 14: Waterproof Key Pad
TSC Demo V1.0 Chapter 3 TSC Demo Functions 3.6 Waterproof Key Pad The system demonstrates waterproof capability of key pad of ATA2508. The below picture is the reference. If water is dropped on the key pad, ATA 2508 still can work normally and do the correct key-value detection. -
Page 15: 4 Tsc Tuning
TSC Demo V1.0 Chapter 4 TSC Tuning 4 TSC Tuning This chapter introduces TSC pad and IC tuning interface and method. 4.1 Tuning Interface For support tuning function using AtLab DCC DP17 tuning kit, the special IDC10 cable is provided. The table below shows the pin assignment of cable. - Page 16 TSC Demo V1.0 Chapter 4 TSC Tuning The picture below shows the 2 terminals of this cable. Figure 4-1: Special IDC10 Cable MCU-AN-500047-E-10 – Page 16...
-
Page 17: Tuning System Build-Up
TSC Demo V1.0 Chapter 4 TSC Tuning 4.2 Tuning System Build-up Connect DCC DP17 tuning kit and TSC demo board through the special IDC10 cable. Then connect the kit into PC though USB cable. In the way, TSC ATA2508 parameter can be tuned and tied on PC software GUI. Refer to “ATA2508 Users Manual V1.4 (EN) v01”... -
Page 18: 5 Demo Firmware
TSC Demo V1.0 Chapter 5 Demo Firmware 5 Demo Firmware This chapter introduces TSC pad and IC tuning interface and method. In this solution, TSC ATA2508 is controlled by MCU through I2C. If MCU hasn’t I2C peripheral just like MB95F204K, I2C communication can be simulated by general IO port. In this case, Config.h on demo F/W “TSC_LPC_1V0”... -
Page 19: 6 Additional Information
TSC Demo V1.0 Chapter 6 Additional Information 6 Additional Information For more Information on FUJITSU MB95200 products, visit the following websites: English version address: http://www.fujitsu.com/cn/fsp/services/mcu/mb95/application_notes.html Chinese version address: http://www.fujitsu.com/cn/fss/services/mcu/mb95/application_notes.html MCU-AN-500047-E-10 – Page 19... -
Page 20: 7 Appendix
TSC Demo V1.0 Chapter 7 Appendix 7 Appendix Figure 2-1: TSC Demo Platform ....................5 Figure 2-2: TSC Tuning Platform ..................... 6 Figure 3-1: Demo System Build-up ..................7 Figure 3-2: IDC10 Pin Assignment ..................7 Figure 3-3: Demo System Power-on ..................8 Figure 3-4: APIS Mode I ......................