Panasonic MK-G1350PWTX Service Manual
  1. Manuals
  2. Brands
  3. Panasonic Manuals
  4. Meat Grinder
  5. MK-G1350PWTX
  6. Service manual
Panasonic MK-G1350PWTX Service Manual

Panasonic MK-G1350PWTX Service Manual

Hide thumbs

Quick Links

TABLE OF CONTENTS

1 Safety Precautions----------------------------------------------- 2
2 Specifications ----------------------------------------------------- 2
4 Operating Instructions------------------------------------------ 4
5 Troubleshooting Guide ----------------------------------------- 7
7 Wiring Connection Diagram ---------------------------------11
Model No.
Destination
PAGE
© Panasonic Corporation 2010 Unauthorized copy-
ing and distribution is a violation of law.
Order Number KAD1010003CE
Meat Grinder
MK-G1350PWTX
PGF
PAGE
loading

Related Manuals for Panasonic MK-G1350PWTX

Summary of Contents for Panasonic MK-G1350PWTX

  • Page 1: Table Of Contents

    4 Operating Instructions------------------------------------------ 4 5 Troubleshooting Guide ----------------------------------------- 7 6 Disassembly and Assembly Instructions ---------------- 8 7 Wiring Connection Diagram ---------------------------------11 8 Exploded View and Replacement Parts List -----------12 © Panasonic Corporation 2010 Unauthorized copy- ing and distribution is a violation of law.

  • Page 2: Safety Precautions

    1 Safety Precautions CAUTION Do not grind too hard meat. If the grinder gets stuck, do not force meat into it. CAUTION You may feel the feed screw vibrating during use. It is not a trouble. Do not over tighten the locking knob. CAUTION Keep in mind that some parts of the grinder cannot be washed in a dishwasher.

  • Page 3: Location Of Controls And Components

    3 Location of Controls and Components...

  • Page 4: Operating Instructions

    4 Operating Instructions 4.1. How to Use ( Caution, Before use, ... How to Clean etc.)

  • Page 7: Troubleshooting Guide

    5 Troubleshooting Guide 5.1. SYMPTOM : A.C. motor interrupted when feeding meat (overloaded). Causes Remedy Too hard meat being fed. Take out the hard meat. Too much meat being fed at once. Reduce the meat feed rate. Used for too long continuously. Follow the specified operating time.

  • Page 8: Disassembly And Assembly Instructions

    6 Disassembly and Assembly Instructions For assembly, refer to the Assembly Instructions, and perform the procedures in the opposite order of disassembly. 6.1. Rubber Cap, Connector U (lower) 1. Turn the locking knob counterclockwise to remove it. 2. Put a bladed screwdriver into each of the two holes at the grinder bottom.
  • Page 9 6.3. Removing the gear case cover, gears and gear case. 1. Remove the two gear case cushions. 2. Remove the four lock screws and detach the gear case cover. 3. Take out the bearing B from inside the gear case cover. •...
  • Page 10 6.4. Replacing the Carbon brush 1. Using a bladed screwdriver, widen the carbon holder. 2. Cut the carbon brush copper wire with nippers. Take out the carbon brush. 3. Fit a new carbon brush in the carbon support plate. 4. Finally close the carbon holder. (Replace both the carbon brushes at once.)

  • Page 11: Wiring Connection Diagram

    7 Wiring Connection Diagram 7.1. Schematic diagram 7.2. Basic Wiring diagram...

  • Page 12: Exploded View And Replacement Parts List

    8 Exploded View and Replacement Parts List 8.1. PARTS LOCATION...
  • Page 13 REPLACEMENT PARTS LIST Notes:Important safety notice • Components identified by mark have special characteristics important for safety. • " When replacing any of these components use only manufacturer's specified parts." MODEL No.MK-G1350PWTX Pcs/Set Safety Ref. No. Part No. Part Name & Description Remarks ...
  • Page 14 8.3. PACKING INSTRUCTION...