Montage-Anschluss-Anleitung ZK-Türmodul BUS-2 ZK-Funktionen Standard ZK-Funktion 2.1.1 Funktionsbeschreibung Durch dieses System ist eine Zuweisung zu Raum-Zeitzonen sowie Protokollierung der Schließ- zeiten und Schlüsselnummern möglich. Der Leser besitzt die Aufgabe einer Leseeinheit. Alarmkontakte: Riegelschaltkontakt, Öffnungskontakt und passiver Glasbruchsensor einsetzbar. ZK-Funktion: unscharfen Zustand besteht die Möglichkeit, eine durch einen Türöffner verriegelte Tür über einen Leser und/oder einen Taster freizugeben.
Montage- Anschluss -Anleitung ZK-Türmodul BUS-2 ZK-Funktion mit Funk-Komponenten Funkfähige Verriegelungselemente (Typen XS Pro in Verbindung mit dem Funk-Modul RS-485 ermöglichen es, kabellose ZK-Systeme in Systeme mit Datenübertragung einzubinden. Das Funk-Modul RS-485 dient dabei als Schnittstelle zwischen XS Pro Komponenten und dem ZK- Türmodul BUS-2.
Montage- Anschluss -Anleitung ZK-Türmodul BUS-2 Mögliche Teilnehmer am Modulbus/RS-485 Bis zu 2 Teilnehmer (Typen beliebig gemischt) können am RS-485 Bus betrieben werden. Ab Firmware V11.xx sind zusätzlich noch bis zu 8 Funk-Module RS-485 möglich. Artikel-Nr. AWE- Teilnehmer Firmware mit Tastatur ohne Tastatur IK3-Leser proX ab V10.xx 023320...
Montage-Anschluss-Anleitung ZK-Türmodul BUS-2 Programmierung Adressschalter S1 BUS-2 Adresse Die im Türmodul befindlichen DIP-Schalter (Adress- schalter S1) dienen zur Einstellung der BUS-2- Adressenwert Teilnehmeradresse. Die einzelnen Codierungen sind dem Programmierprotokoll der Einbruchmelderzentrale zu entnehmen. Dargestellte Schalterstellung bedeutet: Adresse 5 eingestellt! LED- Anzeigen Normalbetrieb: - beim Start, RAM wird initialisiert blinkt 1x...
Montage- Anschluss -Anleitung ZK-Türmodul BUS-2 Verbindung zur Zentrale ST2 entspricht ST1 BUS-2 Summer Daten +U_b 12V DC Deckelkontakt zum nächsten TN BUS-2 Rel 2 BUS-2 ST23 ST12 von Zentrale Kabelschirme Schirm Hinweis: Bei der BUS-2- Anschlusstechnik darf kein Abschlusswiderstand angebracht werden. Die Drahtbrücke ist aufzutrennen, wenn bei störspannungsbehafteten Kabelschirmen die Störungen auf die Betriebsspannung eingekoppelt werden.
Montage-Anschluss-Anleitung ZK-Türmodul BUS-2 Teilnehmer am Modulbus/RS-485 Speziell für Prüf- und Vormontageaufbauten sind am Kabel einiger Leser werkseitig Stecker angelötet. Für die endgültige Installation müssen sie in der Regel abgeschnitten werden. 8.3.1 Leitungslänge und Abschlusswiderstände Gesamtlänge der RS-485 Bus Leitung kann bis zu 2000 m betragen.
Montage- Anschluss -Anleitung ZK-Türmodul BUS-2 8.3.5 RS-485-Bussystem mit mehreren Teilnehmern Werden mehrere RS-485 Teilnehmer eingesetzt, dann gelten die üblichen RS-485-Bus Richtlinien. Die Kapitel 8.3.1 und 8.3.2 sind zu beachten! Beispiel 1: Das Modul befindet sich am Anfang der RS-485-Bus Leitung. Beide Steckbrücken Es wird der Abschlusswiderstand des Moduls verwendet ( JP15 gesteckt...
Montage-Anschluss-Anleitung ZK-Türmodul BUS-2 Meldergruppen, Kontakte, GBS Nicht benötigte Meldergruppeneingänge werden bei der Programmierung der Zentrale keiner Meldegruppe (MG00) zugewiesen. Hinweis zu den 3,3 V DC Meldergruppeneingängen: - offen: 3,3 V - mit 12k1 abgeschlossen: ca. 1,65 V - Öffnungskontakt (ST4) 3,3 V MG-Spannung Für die Öffnungsüberwachung der Tür wird an diesem Eingang z.B.
Page 15
Montage- Anschluss -Anleitung ZK-Türmodul BUS-2 Auch wenn dieser Eingang nicht verwendet wird, muss mit 12k1 abgeschlossen werden! Deckelkontakt ext. Leser 12k1 12k1 frei ÖK Riegelschaltkontakt frei E = Eingang R =12k1 A = Ausgang frei frei Kabelquerschnitt R =12k1 ÖK = Öffnungskontakt ST23 Magnetkontakt)
Montage-Anschluss-Anleitung ZK-Türmodul BUS-2 Türöffner für ZK-Funktion Mit einem Türöffner an der Schlossfalle kann eine ZK-Funktion realisiert werden. Mögliche Türöffnerarten: - Arbeitsstromtüröffner - Ruhestromtüröffner Die ZK-Funktion ist im Zustand "unscharf" aktiv. Über die Zentralenprogrammierung können PIN-Codes und/oder Schlüssel (Datenträger) für eine Türfreigabe berechtigt werden.
Page 17
Montage- Anschluss -Anleitung ZK-Türmodul BUS-2 Taster Türfreigabe TÖ-RMK Riegelschaltkontakt und Rückmeldekontakt TÖ Wird der TÖ-Rückmelde- kontakt verwendet, sollte er mit dem Riegelschalt- Rel 2 kontakt in einer UND- Funktion auf eine gemeinsame Riegel- Ö schaltgruppe gelegt ST23 ST12 werden. U_ext (DC oder AC) Rückmelde- Arbeitsstrom- kontakt...
Montage-Anschluss-Anleitung ZK-Türmodul BUS-2 Inbetriebnahme Nach abgeschlossener Installation und Einschalten der Betriebsspannung müssen in den entspre- chenden Funktionen der Zentralenprogrammierung angelegt werden: Meldergruppen zuweisen, Berechtigungen erteilen, Sperrzeit, evt. Türfreigabezeit sowie die Türöffnerfunktionen. Bei Bedienteilen mit Tastatur kann zusätzlich die Stellenanzahl des Codes, der persönliche Code sowie eine Überfallziffer für den Überfallalarm definiert werden.
Montage- Anschluss -Anleitung ZK-Türmodul BUS-2 Firmware Update Ein Update der Firmware kann an der Zentrale mit WINFEM Advanced über BUS-2 . Hinweis: Beim Update über BUS-2 kann es zu einer Sabotagemeldung an der Zentrale kommen, da das Modul nach dem Update einen Reset durchführt. Fehlersuche Fehlersuche Fehler...
Mounting and Connection Instructions Door controller module for MB AC functions Standard AC function 2.1.1 Function description The system enables allocation to room/time zones as well as the recording of locking times and key numbers. Alarm contacts: A bolt switching contact, a opening contact and a passive glass breakage sensor can be connected to monitor the door.
Mounting and Connection Instructions Door controller module for MB AC function with radio components Locking elements suitable for radio transmission (XS Pro in conjunction with Trafficpoint RS-485 enable the integration of wireless access control systems into systems with data transmission. this case, Trafficpoint RS-485 serves as an interface between XS Pro components and the Door controller module.
Mounting and Connection Instructions Door controller module for MB Application example a/d, AC Staff entrance BUS-2 to ICP Stock Archive Betrieb SAlarm SStörung System- Störung Bereiche Meldungen Einbruch Ü wählen/ ansehen ansehen Sabotage Gruppen Überfall ansehen/ Zusatz- funktionen Pol.-Notruf sperren Info 1 Melder ansehen/...
Mounting and Connection Instructions Door controller module for MB Possible users at Module bus/RS-485 Up to 2 users (types mixed as required) can be operated on the RS-485 bus. From DCM firmware V11.xx upwards up to 8 Trafficpoints RS-485 additionally possible (additio- nal switching devices with their own authorizations).
Mounting and Connection Instructions Door controller module for MB Programming Address switch S1 BUS-2 address The DIP switches located in the Door controller module (address switch S1) are for setting the BUS-2 user address. The individual codes can be found in the Address value programming protocol of the intrusion detection control panel.
Page 29
Mounting and Connection Instructions Door controller module for MB Notes...
Mounting and Connection Instructions Door controller module for MB BUS-2 connections ST2 is equivalent to ST1 BUS-2 Buzzer Data +U_b 12V DC Cover contact to next user BUS-2 Rel 2 BUS-2 ST23 ST23 ST12 ST12 from control panel Cable shields Shield Note: BUS-2 connection technology does not require an end of line resistor.
Mounting and Connection Instructions Door controller module for MB Users at Module bus/RS-485 A plug has been soldered to the cable of the operating unit at the factory especially for test and premounting sets. For the final installation, it usually has to be cut off. 8.3.1 Line length and end of line resistors total length...
Mounting and Connection Instructions Door controller module for MB 8.3.4 RS-485 bus system with several users If several operating units are used, the usual RS-485 bus regulations are applicable. Note Chapters 8.3.1 and 8.3.2! Example 1: module is located at the beginning of the RS-485 bus line.
Mounting and Connection Instructions Door controller module for MB Detector group inputs, contacts, GBS Detector group inputs that are not required, are not allocated to detector groups (DG00) when programming the control panel. 3.3 V DC detector group inputs: - Open: 3.3 V - Terminated with 12k1: Approx.
Page 35
Mounting and Connection Instructions Door controller module for MB If this input is not used, it must be terminated with 12k1. Cover contact ext. reader 12k1 12k1 free Bolt switching contact free E = Input R =12k1 A = Output free free R =12k1...
Mounting and Connection Instructions Door controller module for MB Door strike for AC function AC function can be realized via a door strike at the latch bolt when the system is in a disarmed state. A fail secure door strike or a fail safe door strike can be used as a door strike. Applicable door strikes: - Strike with load current function - Strike with no-load current function...
Page 37
Mounting and Connection Instructions Door controller module for MB AC - Release button Door strike monitoring contact Bolt switching contact Door strike m onitoring contact Bolt switching contact If the door strike monitoring contact is used, it should be Rel 2 connected to a common bolt switching group (AND- function).
Mounting and Connection Instructions Door controller module for MB Start-up On completion of installation and after switching on the operating voltage, the following must be programmed in the corresponding functions of the control panel: Allocation of detector groups, authorization granted, blocking time, possible door release time and door strike functions.
Mounting and Connection Instructions Door controller module for MB Firmware update The firmware can be updated at the control panel with WINFEM Advanced via BUS-2. Note: With an update via BUS-2, a tamper signal may be transmitted to the control panel, as the module activates a reset after the update.