Fujitsu STYLISTIC Q7310 Manual
  1. Manuals
  2. Brands
  3. Fujitsu Manuals
  4. Laptop
  5. STYLISTIC Q7310
  6. Manual

Fujitsu STYLISTIC Q7310 Manual

System expansions and repairs
Hide thumbs
Table of Contents

Quick Links

System expansions and repairs
STYLISTIC Q7310
Version date
Category
Contents
Page 1 of 64
29.06.2020
System expansions and repairs
2
3
4
5
6
7
8
9
10
11
14
15
17
19
21
22
24
26
28
30
31
32
33
35
37
38
40
41
42
43
44
46
48
50
52
54
63
Table of Contents
loading

Related Manuals for Fujitsu STYLISTIC Q7310

Summary of Contents for Fujitsu STYLISTIC Q7310

  • Page 1: Table Of Contents

    Removing the DC-in connector Removing the SmartCard reader Remove mainboard Remove the various covers Removing the inner support plate including the speaker Remove LCD module Spare parts and exploaded-view drawings STYLISTIC Q7310 Disposal informations for recycling companies Page 1 of 64...

  • Page 2: System Expansions And Repairs

    System expansions and repairs We recommend printing out the relevant sections of this chapter prior to installation as the device for installing/removing hardware components needs to be switched off. The following illustrations may differ from your device, depending on its configuration and features. If you have received any further documents with your device, you should read these through carefully.

  • Page 3: Information On The Installation And Removal Of Components

    Information on the installation and removal of components Please pay attention to the locking mechanism (indentations and centring pins) when installing hardware components. Note that some components on the mainboard may be very hot if the device was in use shortly before the case was removed. Utmost care is required during installation and removal to avoid damaging components.

  • Page 4: Screws

    Screws Screw: M2.5XL3 (D4.5) Screwdriver: Phillips PH00 Screw: M2.5XL4 Screwdriver: Phillips PH00 Screw: M2.5XL6 (D4.5) Screwdriver: Phillips PH00 Screw: M2XL2.5 Screwdriver: Phillips PH00 Screw: M3XL3.5-1 Screwdriver: Phillips PH00 Return to Table of Contents Page 4 of 64...

  • Page 5: Tools

    Tools Screwdriver: Phillips, size PH00 Plastic tool Plastic tool Return to Table of Contents Page 5 of 64...

  • Page 6: Removing / Fitting The Keyboard

    ► STYLISTIC Q7310 upwards (green arrows). To reconnect the STYLISTIC Q7310 to its keyboard, gently refit the tablet on it (red arrows). The guidance indicator (blue circle) on the ► tablet and keyboard will support you to find the correct position.

  • Page 7: Removing / Fitting The Cradle

    Disconnect the STYLISTIC Q7310 tablet from its cradle by pressing the release button (yellow arrow) and pulling the STYLISTIC Q7310 ► upwards (green arrows). To reconnect the STYLISTIC Q7310 to its cradle, gently refit the tablet on it (red arrows). The guidance indicator (blue circle) on the ► tablet and cradle will support you to find the correct position.

  • Page 8: Removing / Fitting The Sim Tray

    Removing / fitting the SIM tray Required work steps: ■ Remove keyboard ► The SIM and SD card cover is on the bottom right next to the keyboard connector. Open it (green arrow) and remove the SIM card holder (yellow arrow). Pull out the SIM card holder in the yellow arrow direction.

  • Page 9: Removing / Fitting The Pen

    Removing / fitting the pen ► Pull the pen straight out of the pen garage (green arrow). The pen can be attached with a ribbon running through the eyelet (red rectangle) under the pen garage. Undo it to be able to replace the pen.

  • Page 10: Mandatory Support Bulletins For Disassembly

    Mandatory Support Bulletins for Disassembly SB-M-10030 Minimum requirements to properly finalise hardware repairs on mobile systems SB-M-15007 WIN8x & WIN10 - Spare product key for repaired devices For any information about ESD, please refer to the web-based training course “ESD in electronics“...

  • Page 11: Removing The Lcd Back Cover Assy

    Removing the LCD back cover assy Required work steps: Required tools: ■ Remove keyboard ■ Screwdriver: Phillips, size PH00 ■ Remove cradle ■ Plastic tool ■ Remove pen Always ensure there is a static discharge (e.g. by touching a grounded object) prior to commencing with the work. ►...
  • Page 12 ► Use plastic tools to carefully disconnect the LCD back cover assy from the STYLISTIC. The plastic tool is to be placed at short distances and in the slits (yellow arrows) between the lower assy and the display to ► undo the plastic latches bit by bit.
  • Page 13 ► Carefully place the LCD back cover assy in a position where the cables are not taut. First carefully disconnect the battery cable from the battery (red circle). ► ► Carefully disconnect the SiBeam flexprint cable (yellow circle). This cable is integrated in the LCD back cover assy. ►...

  • Page 14: Remove Battery

    Remove battery Required work steps: Required tools: ■ Screwdriver: Phillips, size PH00 ■ Remove keyboard ■ Remove cradle ■ Remove pen ■ Removing the LCD back cover assy Remove the three M2XL3 screws (yellow circles). ► ► Remove the battery from the device (direction of the green arrows). Return to Table of Contents Page 14 of 64...

  • Page 15: Remove M.2 Module

    Remove M.2 module Required work steps: Required tools: ■ Screwdriver: Phillips, size PH00 ■ Remove keyboard ■ Remove cradle ■ Remove pen ■ Removing the LCD back cover assy ■ Remove battery Remove the M2XL2.5-0 screw (yellow circle). ► Page 15 of 64...
  • Page 16 It can then be easily pulled upwards and removed (blue arrow). ► Please note! ■ Due to the M.2 interface, no conventional HDDs or SSDs with a common form factor can be used in the STYLISTIC Q7310. Return to Table of Contents Page 16 of 64...

  • Page 17: Removing The Docking Connector

    Removing the docking connector Required work steps: Required tools: ■ Screwdriver: Phillips, size PH00 ■ Remove keyboard ■ Remove cradle ■ Remove pen ■ Removing the LCD back cover assy ■ Remove battery Disconnect the flexprint cable of the docking connector (yellow circle). ►...
  • Page 18 Release the docking connector by moving it in the direction of the arrow (yellow). ► As soon as you have carefully pulled it out of the recess provided, you can lift it out (green arrows). ► Return to Table of Contents Page 18 of 64...

  • Page 19: Remove Pen Garage

    Remove pen garage Required work steps: Required tools: ■ Screwdriver: Phillips, size PH00 ■ Remove keyboard ■ Remove cradle ■ Remove pen ■ Removing the LCD back cover assy ■ Remove battery Remove the screw M2XL3 (yellow circle). ► Remove the adhesive tape and the cable (red flashes). ►...
  • Page 20 After successful replacement, route the SAR antenna cable through the designated duct (yellow arrow). ► Return to Table of Contents Page 20 of 64...

  • Page 21: Remove The Application Button Sub Board

    Remove the application button sub board Required work steps: Required tools: ■ Screwdriver: Phillips, size PH00 ■ Remove keyboard ■ Remove cradle ■ Remove pen ■ Removing the LCD back cover assy ■ Remove battery ■ Remove pen garage Remove the two screws M2XL3 (yellow circles). ►...

  • Page 22: Remove Buttons, Holder For Button Set, Cover For Button Section

    Remove buttons, holder for button set, cover for button section Required work steps: Required tools: ■ Screwdriver: Phillips, size PH00 ■ Remove keyboard ■ Remove cradle ■ Remove pen ■ Removing the LCD back cover assy ■ Remove battery Release and carefully remove the cover for button section, the single keys and the holder for button set from their intended ►...
  • Page 23 Pull the four nubs of the holder for button set (blue rectangle) out of the provided recesses (yellow circles). ► Below you can see a picture with a top view of these recesses. ► Return to Table of Contents Page 23 of 64...

  • Page 24: Removing The Wwan Antennas

    Removing the WWAN antennas Required work steps: Required tools: ■ Screwdriver: Phillips, size PH00 ■ Remove keyboard ■ Remove cradle ■ Remove pen ■ Removing the LCD back cover assy ■ Remove battery ■ Remove pen garage ■ Remove the application key sub board Picture 1 Remove the two screws M2XL3 (yellow circles).
  • Page 25 Picture 2 Place the gasket in the fan direction (yellow arrow). ► Disconnect both WWAN antenna cables (red circles) from the LTE module. ► ► Remove both WWAN antennas from the device (green arrow). Please note! When fitting the LTE module, make sure that both antenna cables are properly connected. The yellow cable must be connected to the “MAIN”...

  • Page 26: Remove Lte Module

    Remove LTE module Required work steps: Required tools: ■ Screwdriver: Phillips, size PH00 ■ Remove keyboard ■ Remove cradle ■ Remove pen ■ Removing the LCD back cover assy ■ Remove battery Disconnect and remove the flexprint cable which is fitted over the LTE module and leads to the camera sub board (yellow ►...
  • Page 27 Disconnect both WWAN antenna cables (red circles) from the LTE module. ► ► Remove the M2XL2.5-0 screw (yellow circle). ► Now the LTE module is loose and can be removed by slightly increasing its inclination in the direction of the blue arrow. Warning! The antenna cables are routed through a cable duct into the camera module (yellow arrow).

  • Page 28: Remove The Camera Module

    Remove the camera module Required work steps: Required tools: ■ Screwdriver: Phillips, size PH00 ■ Remove keyboard ■ Remove cradle ■ Remove pen ■ Removing the LCD back cover assy ■ Remove battery ■ Remove LTE module ► Put the gasket aside to the right (blue arrow). ►...
  • Page 29 ► Carefully release the camera module (blue arrow) in several points. When the position shown above has been reached, the module can be lifted out (green arrow). This module connects different components, which can be ordered separately. The next chapters describe how to ►...

  • Page 30: Removing The Rear Camera

    Removing the rear camera Required work steps: Required tools: ■ Screwdriver: Phillips, size PH00 ■ Remove keyboard ■ Remove cradle ■ Remove pen ■ Removing the LCD back cover assy ■ Remove battery ■ Remove LTE module ■ Remove the camera module ►...

  • Page 31: Removing The Camera Sub Board

    Removing the camera sub board Required work steps: Required tools: ■ Screwdriver: Phillips, size PH00 ■ Remove keyboard ■ Plastic tool ■ Remove cradle ■ Remove pen ■ Removing the LCD back cover assy ■ Remove battery ■ Remove LTE module ■...

  • Page 32: Removing The Front Camera

    Removing the front camera Required work steps: Required tools: ■ Screwdriver: Phillips, size PH00 ■ Remove keyboard ■ Plastic tool ■ Remove cradle ■ Remove pen ■ Removing the LCD back cover assy ■ Remove battery ■ Remove LTE module ■...

  • Page 33: Remove Sar Antennas

    Remove SAR antennas Required work steps: Required tools: ■ Plastic tool ■ Remove keyboard ■ Remove cradle ■ Remove pen ■ Removing the LCD back cover assy ■ Remove battery ■ Remove LTE module ■ Remove pen garage ■ Remove the application key sub board ■...
  • Page 34 ► Release carefully the first SAR antenna from the WWAN antenna (red rectangle). Use a plastic tool if necessary. ► Release the second SAR antenna (blue rectangle) from the camera module. Use a plastic tool if necessary. Return to Table of Contents Page 34 of 64...

  • Page 35: Removing The Wlan Antennas

    Removing the WLAN antennas Required work steps: Required tools: ■ Screwdriver: Phillips, size PH00 ■ Remove keyboard ■ Remove cradle ■ Remove pen ■ Removing the LCD back cover assy ■ Remove battery Remove the two M2XL3 screws (yellow circle). ►...
  • Page 36 Please note! When fitting the WLAN antennas, make sure that both antenna cables are properly connected. The grey cable must be connected to the “AUX” port and the black one to the “MAIN” port. (grey -> AUX; black -> MAIN) Return to Table of Contents Page 36 of 64...

  • Page 37: Remove Cmos Battery

    Remove CMOS battery Required work steps: Required tools: ■ Screwdriver: Phillips, size PH00 ■ Remove keyboard ■ Remove cradle ■ Remove pen ■ Removing the LCD back cover assy ■ Remove battery Disconnect the cable (yellow circle). ► Carefully remove the CMOS battery (red rectangle) and the associated cable. ►...

  • Page 38: Removing The Usb / Audio Sub Board

    Removing the USB / audio sub board Required work steps: Required tools: ■ Screwdriver: Phillips, size PH00 ■ Remove keyboard ■ Remove cradle ■ Remove pen ■ Removing the LCD back cover assy ■ Remove battery ► Disconnect both flexprint cables (red circles). Carefully disconnect the pen garage cable (yellow circle).
  • Page 39 Afterwards the USB/audio sub board can be removed in the green arrow direction. ► Return to Table of Contents Page 39 of 64...

  • Page 40: Removing The Fingerprint Sensor

    Removing the fingerprint sensor Required work steps: Required tools: ■ Screwdriver: Phillips, size PH00 ■ Remove keyboard ■ Remove cradle ■ Remove pen ■ Removing the LCD back cover assy ■ Remove battery Please observe this information when you use the fingerprint sensor! ►...

  • Page 41: Remove Corner Rubbers

    Remove corner rubbers Required work steps: Required tools: ■ Screwdriver: Phillips, size PH00 ■ Remove keyboard ■ Remove cradle ■ Remove pen ■ Removing the LCD back cover assy ■ Remove battery ► Lift each corner rubber from its bracket. Return to Table of Contents Page 41 of 64...

  • Page 42: Remove Fan

    Remove fan Required work steps: Required tools: ■ Screwdriver: Phillips, size PH00 ■ Remove keyboard ■ Remove cradle ■ Remove pen ■ Removing the LCD back cover assy ■ Remove battery ► Remove both screws M2XL3 (yellow circles). The cable of the fan connector may be a bit difficult to disconnect (red circle). In this case, try disconnecting it with two ►...

  • Page 43: Removing The Dc-In Connector

    Removing the DC-in connector Required work steps: Required tools: ■ Screwdriver: Phillips, size PH00 ■ Remove keyboard ■ Remove cradle ■ Remove pen ■ Removing the LCD back cover assy ■ Remove battery Disconnect the connection cable from the mainboard (red circle). ►...

  • Page 44: Removing The Smartcard Reader

    Removing the SmartCard reader Required work steps: Required tools: ■ Screwdriver: Phillips, size PH00 ■ Remove keyboard ■ Remove cradle ■ Remove pen ■ Removing the LCD back cover assy ■ Remove battery ► Disconnect the cables (yellow circles). Remove the M2XL3 screw (red circle). ►...
  • Page 45 Push the SmartCard reader slightly upwards (blue arrow). ► Lift the SmartCard reader (green arrow). ► Return to Table of Contents Page 45 of 64...

  • Page 46: Remove Mainboard

    Remove mainboard Required work steps: Required tools: ■ Screwdriver: Phillips, size PH00 ■ Remove keyboard ■ Remove cradle ■ Remove pen ■ Removing the LCD back cover assy ■ Remove battery ■ Remove M.2 module ■ Remove LTE module ■ Removing the DC-in connector Please note! ■...
  • Page 47 Now carefully lift the mainboard (green arrows). ► ■ When you remove the mainboard, pay attention also to the housing, as the mainboard may be a bit jammed or canted. ■ The device may be equipped with antenna cables even if no WLAN/WWAN module is installed. ■...

  • Page 48: Remove The Various Covers

    Remove the various covers Required work steps: Required tools: ■ Screwdriver: Phillips, size PH00 ■ Remove keyboard ■ Remove cradle ■ Remove pen ■ Removing the LCD back cover assy ■ Remove battery ■ Remove M.2 module ■ Remove LTE module ■...
  • Page 49 Please note! These covers are not supplied as part of the LCD assy. ► Return to Table of Contents Page 49 of 64...

  • Page 50: Removing The Inner Support Plate Including The Speaker

    Removing the inner support plate including the speaker Required work steps: Required tools: ■ Screwdriver: Phillips, size PH00 ■ Remove keyboard ■ Remove cradle ■ Remove pen ■ Removing the LCD back cover assy ■ Remove battery ■ Remove M.2 module ■...
  • Page 51 ► Carefully move and lift the inner support plate out (green arrows). Return to Table of Contents Page 51 of 64...

  • Page 52: Remove Lcd Module

    Remove LCD module Required work steps: Required tools: ■ Screwdriver: Phillips, size PH00 ■ Remove keyboard ■ Remove cradle ■ Remove pen ■ Removing the LCD back cover assy ■ Remove battery ■ Remove M.2 module ■ Remove LTE module ■...
  • Page 53 Remove the various covers Please note!  Two magnets (yellow circles) are integrated in the LCD assy. These two magnets enable the STYLISTIC Q7310 to be charged via the keyboard’s DC-in connector. Return to Table of Contents Page 53 of 64...

  • Page 54: Spare Parts And Exploaded-View Drawings Stylistic Q7310

    Spare parts and exploaded-view drawings STYLISTIC Q7310 Drawing Spare part Internal spare part name for ordering number Mechanical parts: LCD back cover depending on the device configuration Corner round cover (grip) Corner rubber covers SIM tray AC adapter Main battery...
  • Page 55 Page 55 of 64...
  • Page 56 Page 56 of 64...
  • Page 57 Page 57 of 64...
  • Page 58 Page 58 of 64...
  • Page 59 Page 59 of 64...
  • Page 60 Page 60 of 64...
  • Page 61 Page 61 of 64...
  • Page 62 Page 62 of 64...

  • Page 63: Disposal Informations For Recycling Companies

    Disposal informations for recycling companies Disposal information for recycling companies These instructions are for the complete dismantling of a Fujitsu product. All materials can thereby be disposed of according to their provision in the EC directive 2012/19/EC (Waste Electrical and Electronic Equipment (WEEE)).
  • Page 64 Plastics which contain brominated flame This product may contain plastic parts with retardant Brominated flame retardants but to the best of our knowledge we provide this information to sort them out. Plastic parts location can be visually identified by their typical design function for the product (also shown in the disassembly manual).

This manual is also suitable for:

Q7310mc5bmin

Table of Contents