Fujitsu Stylistic 3400 Assembly And Use Instructions

Wall-mount cradle
Hide thumbs Also See for Stylistic 3400:

Quick Links

FMW42CR3
Wall-Mount Cradle
Assembly and Use Instructions
Stylistic 3400
The Stylistic 3400 wall-mount cradle is designed to
provide a convenient, secure, hands-free station for
your pen tablet and keyboard.
The wall-mount cradle uses high-usage DC Input
and Universal Serial Bus (USB) contact pins to
connect to the pen tablet. The USB pins are used for
interfacing with the USB keyboard. (Note that these
connectors are not visible or accessible when the
wall-mount cradle is installed.)
Assembly Instructions
The Stylistic 3400 wall-mount cradle is shipped
partially disassembled. Follow the instructions
below to assemble the unit. Note that these
instructions are for the assembly of the cradle, not
for mounting the cradle. The mounting and
electrical connection of the cradle are determined by
local procedures.
Parts Included
Verify that all parts and tools listed below are
present before proceeding with the assembly.
Table 1: Parts Included in Wall Mount Kit
Quantity
1
Wall Mount Back Assembly
1
Wall Mount Tray Assembly
1
Cradle Assembly (plastic)
2
Keys
1
Hardware Kit, consisting of:
6
Screws (short, black)
4
Screws, Phillips
(black, with star lockwasher)
2
Screws (silver)
2
Flat Washers
2
Ty-Wraps
Additional Parts Required
In order to use the wall mount cradle most
effectively, it is necessary for you to purchase the
following parts from an authorized reseller.
4/00
0
0
Part
TM
0
Stylistic 3400 is a trademark of Fujitsu PC Corp. © 2000 Fujitsu PC Corp.
Page 1 of 4
Table 2: Additional Parts Required
Quantity
1
USB Keyboard (FMWKB5x)*
1
AC Adapter (FMWAC6x)*
*The "x" in the part numbers in Table 2 refers to the suffix
associated with the localized version of keyboard or AC Adapter.
Tools Required
The proper assembly of the wall mount cradle
requires the use of the following common tools.
Table 3: Tools Required
Tool
Screwdriver
Wrench
Pliers
Installing the Cradle
1. Lay the wall mount back assembly on your
work surface.
2. Position the cradle assembly over the back
assembly so that the four screw holes in the
cradle align with the holes in the back assembly.
Ensure that the circuit card and cable extend
from the bottom of the cradle (reference Fig. 1).
Cradle Assembly
Screws
Standoffs
Wall Mount Back Assembly
Figure 1. Mounting the Cradle to the Back Assembly
FUJITSU PC CORPORATION
Part
0
Description
Phillips
Allen, 3/32
Cutting
0
Circuit Card
58-0710-00A
loading

Summary of Contents for Fujitsu Stylistic 3400

  • Page 1 Circuit Card Wall Mount Back Assembly Figure 1. Mounting the Cradle to the Back Assembly Stylistic 3400 is a trademark of Fujitsu PC Corp. © 2000 Fujitsu PC Corp. 4/00 Page 1 of 4 58-0710-00A...
  • Page 2 Velcro. each side, two on bottom) 15. Route the DC power cord through the Figure 3. Wall Mount Components cutaway. Stylistic 3400 is a trademark of Fujitsu PC Corp. © 2000 Fujitsu PC Corp. 4/00 Page 2 of 4 58-0710-00A...
  • Page 3 Figure 6. Rear of Wall Mount Assembly Stylistic 3400 is a trademark of Fujitsu PC Corp. © 2000 Fujitsu PC Corp. 4/00 Page 3 of 4...
  • Page 4 4. When not in use, lift the keyboard tray so that the magnetic latches attach to the metal striker plates on the front of the brackets. Stylistic 3400 is a trademark of Fujitsu PC Corp. © 2000 Fujitsu PC Corp. 4/00 Page 4 of 4...

This manual is also suitable for:

Fmw42cr3