Hide thumbs Also See for MI1002-W:

Quick Links

MITSUBISHI ELECTRIC
INDUSTRIAL PC
MI1002-W,MI1002-W-CL
START-UP GUIDE
BCN-P5999-0990-C(1901)NEC Ver.3 Jan. 2019
Before using this product, please read this manual and the relevant manuals carefully a nd pay full
attention to safety to handle the product correctly.
SAFETY PRECAUTIONS
Follow the instructions in this document for the safe use of this product. User's Manual describes hazardous
parts of the product, possible hazards, and how to avoid them. Components of the product with possible
danger are indicated with a warning label placed on or around them (or, in some cases, by printing the
warnings on the computer).
In User's Manual or on warning labels, "
Warning
" or "
Caution!
ion!
These terms are defined as follows:
Warning
Indicates the potential for death or serious injury.
Indicates there is a risk of burns, other personal injury,
Caution!
or property damage.
Under some circumstances, failure to observe the precautions given under "
serious consequences.
Observe the precautions of both levels because they are important for personal and system safety.
Make sure that the end users read this manual and then keep the manual in a safe place for future reference.
Precautions and notices against hazards are presented with one of the following three symbols.
This symbol indicates the presence of a hazard if the
Attention
instruction is ignored. An image in the symbol illustrates
the hazard type.
This symbol indicates prohibited actions. An image in the
Prohibited
symbol illustrates a particular prohibited action.
action
This symbol indicates mandatory actions. An image in the
Mandatory
symbol illustrates a mandatory action to avoid a particular
action
hazard.
Symbols used in this manual and on warning labels
Attention
Indicates the potential for
smoke and/or fire to occur.
Indicates the potential for damage
caused by high temperatures.
Indicates the possibility that you
get your fingers pinched between
the mechanical parts resulting in
injuries.
Prohibited actions
Do not disassemble, repair, or
modify this product. Otherwise,
an electric shock or fire may be
caused.
Do not install this product near a
fire. Otherwise a fire may be
caused.
Do not touch this product.
Otherwise, an electric shock
may be caused.
SAFETY PRECAUTIONS - CONT'D -
Caution!
Do not use this product in an environment where corrosive gas is present.
Do not install this product in a place subject to corrosive gases including sulfur dioxide,
hydrogen sulfide, nitrogen dioxide, chlorine, ammonia, or ozone. Do not install this
product in an environment containing corrosion promoting components such as
sodium chloride and sulfur and conductive metal etc. in dust and air. Failure to follow
this warning may corrode the printed board in this product, le a ding to malfunction,
smoke emission or fire. If you have any questions, please contact your sales or
maintenance representative.
Remove AC power cable when connecting interface cables.
Remove the AC power cable from the outlet or other supply power source when
connecting or removing interface cables.
Connecting or removing interface cables while the AC power cable is connected to the
outlet or other supply power source might result in electric shock.
Use only the specified interface cable.
Use only interface cables provided by MITSUBISHI ELECTRIC CORPORATION and
locate a proper device and connector before connecting a cable. Using an
unauthorized cable or connecting a cable to an improper destination may cause a
short circuit, resulting in a fire. Also, observe the following notes on using and
connecting an interface cable.
● Do not use any damaged cable connector. ● Do not step on the cable.
● Do not place any object on the cable.
● Do not use the server with loose cable connections.
For more information about interface cables, please contact your sales or
maintenance representative.
Secure cables in place.
Be sure to secure the power cable and interface cables in place. Incomplete installation
causes a loose connection, resulting in smoke or fire.
Hold the plug part when removing the AC power cable and interface cables.
Pull the plug by holding the plug part to disconnect the AC power cable and interface
cables. Pulling these cables by holding the cord will cause breakage and might cause
fires to occur.
Notes for Maintenance
Warning
Do not remove the lithium metal battery (button type).
A lithium metal battery (button type) is installed in this product. Do not attempt to
remove this lithium metal battery (button type). Exposing the battery to flame or water
may cause it to catch fire or rupture.
If the product does not work normally due t o the dead battery, please contact your
sales or maintenance representative. Never disassemble or replace the battery by
yourself.
Remove AC power cable when connecting interface cables.
Remove the AC power cable from the outlet or other supply power source when
connecting or removing interface cables.
Connecting or removing interface cables while the AC power cable is connected to the
outlet or other supply power source might result in electric shock.
Caution!
Do not touch high temperature parts.
Do not touch the chassis and AC power adaptor immediately after using the device.
They are hot and might cause burns when touched.
Wait at least 30 minutes after turning the power to the main device OFF before
installing/removing devices installed in the main unit.
Secure cables in place.
Be sure to secure the power cable and interface cables in place. Incomplete
installation causes a loose connection, resulting in smoke or fire.
Do not use while dust is accumulated on the AC power cable.
Do not use this main unit while dust is accumulated on the power cable plug. Long
periods of use without cleaning the dust that has accumulated on the power cable plug
might result in electric discharge between the plug a nd pins and causes fires to occur.
Notes on maintenance
Please read the manual for each component before maintenance.
Do not disassemble.
Please do not disassemble the power supply, battery, optical drives, and disk drives
in a manner other than that for which described in this document.
Not only does the product not work properly but also there is a risk of electric shock or
fire.
Mandatory actions
Unplug the power cord of this
product. Otherwise, an electric
shock or fire may be caused.
Make sure equipment is properly
grounded.
Notations in this manual
Indicates items that must be observed in handling the hardware.
Safety Notes
General Notes
Warning
Do not use the product if any smoke, odor, or noise is present.
" is used to indicate a degree of danger.
Do not insert needles or metal objects.
Caution!
" may lead to
Caution!
Keep water or foreign objects away from the product.
Example
Electric shock risk
Notes on Power Connections
Example
Do not disassemble
Warning
Example
Plug the power cord into an outlet that matches the voltage of the unit.
Disconnect a plug
Do not hold the power plug with a wet hand.
Indicates the risk of electric shock.
Secure safety grounding.
Indicates there is a risk of
explosion that can result in injuries.
Indicates an attention that cannot
be specifically identified.
Make sure to follow the instruction.
Do not use this product in places
near water or liquids. Otherwise an
electric shock or fire may be
caused.
Do not touch with wet hand.
Otherwise, an electric shock
may be caused.
Indicates a general prohibited
action that cannot be specifically
identified.
Notes for Operation
Caution!
Do not touch during thunderstorms.
Keep creatures away from this product.
Do not place any objects on this product.
Do not touch high temperature parts.
Warning Labels
● Do not use any damaged cable.
A warning label is placed on the components and peripherals that require careful handling (The warning label
is printed or attached). The warning labels contain information about possible dangers in dealing with this
product. Therefore, do not peel off, cover, or dirty the w arning labels. If no warning label is printed or attached
on this product, or if the attached or printed warning label is peeling off or dirty, please contact your sales
representative.
Precaution for transfer or disposal of this product
Be sure to erase important data in the storage completely before transferring or disposing of
this product. Even if the data is invisible on the OS, it may remain in storage. To prevent data
leakage to third parties, the customer is responsible for erasing the data.
● Precautions for transferring this product to a third party
When transferring (or selling) this product to a third party, please pass on this document, the attached parts
and instructions, license agreement and other documents together with the product.
● Disposal precautions
When disposing of this product, treat it as industrial waste.
This product contains lithium battery. When disposing of batteries, separate them from other wastes
according to the local regulations. For details on battery regulations in EU member states, refer to the
User's Manual.
Be sure to dispose of the attached AC adaptor an d power cord together with this product to prevent
diversion for other purposes.
Cautions for transportation by air or sea
When transporting lithium batteries, follow the transportation regulations. For details on the regulat ions, refer
to Mitsubishi Technical Bulletins as follows.
Precautions for transport regulations on lithium batteries (F A-A-0259)
Indicates a mandatory action that
cannot be specifically identified.
Make sure to follow the
instruction.
If smoke, an abnormal odor or a sound is generated from the product, immediately
turn off the main unit, unplug the power cable from the outlet, and then contact your
nearest sales agent or maintenance service company. An electric shock or fire might
result if you continue to use the product.
Do not remove rubber caps or other covers on this product to insert needles, metal
objects, or other foreign objects into openings. Doing so may cause an electric shock,
burns, or fire.
Do not drop liquids such as water or other foreign objects such as a pin or a paper clip
into this product. Failure to follow this warning may cause an electric shock, a fire. If
such things accidentally enter the product, immediately turn off the power and
disconnect the power plug from the outlet. Do not disassemble the product, and
contact your sales representative or a maintenance service company.
Plug the power cord supplied with this product into a 100V outlet in line with the voltage
inscribed on the unit. When using this product in a country or region other than Japan,
prepare a power cord corresponding to the power supply for the country or region
where this product will be used. Fa ilure to use an appropriate power cable may cause
a fire.
Do not insert/remove the power cable plug with wet hands.
Failure to follow this warning may cause an electric shock.
Connect the 3-pin power plug of the attached AC power cable to a 3 -pin outlet. Use
the attached conversion plug for the double-pole outlet to connect the earth cable to
the earth terminal for the double -pole outlet. Secure grounding for safety ( t o prevent
electric shock) by using the FG cable. Ground the main unit before connecting the
power plug.
Disconnect the power plug from the power source before disconnecting grounding.
Do not remove the main unit cover when the power plug is connected to
the AC outlet. Failure to follow this warning may cause an electric shock.
Keep small animals, insects, and other creatures away from this product. Hair or other
waste matter from the creature may enter this product and cause a fire or electric
shock.
Doing so may cause the product to malfunction, or the object placed on the product
may fall and cause personal injury or damage to nearby personal belongings.
Do not touch the chassis and AC power adaptor immediately after using the device.
They are hot and might cause burns when touched.
Wait at least 30 minutes after turning the power to the main device OFF before
installing/removing devices installed in the main unit.
CAUTION: For use with Information Technology Equipment
INDOOR USE ONLY
MI1002-W
AC Adapter
Caution!
Plug the power cord into the specified outlet.
Use a 3-pin outlet with ground electrode or 2 -pin outlet with ground terminal that
matches the specified voltage. If you are using a 2 -pin outlet with ground terminal, use
a 2-pin conversion plug with a ground wire supplied with this prod uct and connect the
ground wire securely to the ground terminal of the outlet. Use of an outlet other than
that specified may result in fire or electrical leakage.
Do not use extension cords.
Do not install the server in any environment that requires an extension cord.
Connecting to a cord that does not conform to the power supply specs of this product
causes overheating, resulting in fire.
Do not connect power cable to overloaded extension cords.
The electric current exceeding the rated flow overheats the outlet, which may cause a
fire.
Hold the plug part when removing the AC power cable.
Pull the plug by holding the plug part to disconnect the AC power cable. Pulling the
AC power cable by holding the cord will cause breakage and might cause fires to
occur.
Secure the AC power cable in place.
Be sure to secure the AC power cable in place. Incomplete installation causes a loose
connection, resulting in smoke or fire .
Use the authorized AC power cable.
Use only the AC power cable supplied with the product . Electric current exceeding the
rated flow could cause fire. Also, observe the following precautions to prevent
electrical shock or fire caused by a damaged power cable.
◇ Do not stretch the power cable.
◇ Do not bend the power cable.
◇ Do not step on the power cable.
◇ Do not pinch the power cable.
◇ Do not secure the power cable with staples or equivalents.
◇ Uncoil the power cable before use.
◇ Keep chemicals away from the power cable.
◇ Do not place any object on the power cable.
◇ Do not alter, modify, or repair the power cable.
◇ Do not use a damaged power cable. Replace the damaged power cable with a
power cable of the same standard. Contact your sales representative or a
maintenance service company for replacement.
Do not use the attached power cable for any other devices or usage.
The power cable that comes with the product is designed for this product. Do not use the
attached power cord for any other products or purposes. Doing so may cause a fire or
an electric shock.
Notes on Installation Environment
Warning
Do not connect the ground wire to a gas pipe.
Never connect the ground wire to a gas pipe. Failure to follow this warning may cause
a gas explosion or a fire.
Caution!
Install or store this product in the specified place.
Do not install this product in the following places or any place other than specified in
this manual. Failure to follow this instruction may cause a fire.
● A dusty or humid place
● A place exposed to direct sunlight or rainwater
● A place where flammable gas or corrosive gas is present
● An unstable place
FCC statement
This equipment has been tested and complies with the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. The se limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accord a nce with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case the user will be required to correct the interference at his own
expense.
Industry Canada statement
This Class A digital apparatus complies with Canadian ICES - 003.
Cet appareil numérique de la classe A est conforme à la norme NMB - 003 du Canada.
European Community statement
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case
the user may be required to take adequate measures.
Harmonic Current Standard Compliance
This product complies with harmonic current standard EN 61000-3-2.
This product has been designed and produced to meet the harmonic environmental target level of the
commercial power system according to "Electromagnetic compatibility (EMC) - Part 3-2: Limits - Limits for
harmonic current emissions (equipment input current ≦ 20 A per phase)" of EN.
Using this product
(1).
This product ("the PRODUCT") shall be used in conditions;
i) where any problem, fault or failure occurring in the PRODUCT, if any, shall not lead to any major or
serious accident; and
ii) where the backup and fail-safe function are systematically or automatically provided outside of the
PRODUCT for the case of any problem, fault or failure occurring in the PRODUCT.
(2).
The PRODUCT has been designed and manufactured for the purpose of being used in general
industries. MITSUBISHI SHALL HAVE NO RESPONSIBILITY OR LIABILITY (INCLUDING, BUT NOT
LIMITED TO ANY AND ALL RESPONSIBILITY OR LIABILITY BASED ON CONTRACT, WARRANTY,
TORT, PRODUCT LIABILITY) FOR ANY INJURY OR DEATH TO PERSONS OR LOSS OR DAMAGE
TO PROPERTY CAUSED BY the PRODUCT THAT ARE OPERATED OR USED IN APPLICATION NOT
INTENDED OR EXCLUDED BY INSTRUCTIONS, PRECAUTIONS, OR WARNING CONTAINED IN
MITSUBISHI'S USER, INSTRUCTION AND/OR SAFETY MANUALS, TECHNICAL BULLETINS AND
GUIDELINES FOR the PRODUCT.
("Prohibited Application")
Prohibited Applications include, but not limited to, the use of the PRODUCT in;
 Nuclear Power Plants and any other power plants operated by Power companies, and/or any other
cases in which the public could be affected if any problem or fault occurs in the PRODU C T.
 Railway companies or Public service purposes, and/or any other cases in which establishment of a
special quality assurance system is required by the Purchaser or End User.
 Aircraft or Aerospace, Medical applications, Train equipment, transport equipment such as Elevator
and Escalator, Incineration and Fuel devices, Vehicles, Manned transportation, Equipment for
Recreation and Amusement, and Safety devices, handling of Nuclear or Hazardous Materials or
Chemicals, Mining and Drilling, and/or other applications where there is a significant risk of injury to
the public or property.
Confirmation method in the manufacture date
Equipment base label Serial No. reference
example ) TSBH12345678
H: manufacturing age (A:2010, B:2011, ... , H: 2017, I:2018, ...)
12: manufacturing month (01:January, ... , 12:December)
This product is developed and manufactured with NEC Corporation.
Produced by NEC Corporation
loading

Summary of Contents for Mitsubishi Electric MI1002-W

  • Page 1 Use only the specified interface cable. They are hot and might cause burns when touched. Use only interface cables provided by MITSUBISHI ELECTRIC CORPORATION and Wait at least 30 minutes after turning the power to the main device OFF before This is a Class A product.
  • Page 2 When using the MI1002-W-CL, prepare a power cable that conforms to the power supply to be used and RS-485 Device with a serial interface conforming to the RS-485 standard Use of an outlet other than that specified causes fire and electrical the safety standards of the use area.

This manual is also suitable for:

Mi1002-w-cl