Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT: pLEASE REAd THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OpERATIONAL REQUIREMENTS, WARNINGS, ANd
CAUTIONS. USE THIS pROdUCT CORRECTLY, ANd WITH CARE FOR THE pURpOSE FOR WHICH IT IS INTENdEd. FAILURE TO dO SO
MAY CAUSE dAMAGE ANd/OR pERSONAL INJURY ANd WILL INVALIdATE THE WARRANTY.
1. SAFETY INSTRUCTIONS
dO NOT use the roof box if any parts are missing or damaged as this may cause failure or possible personal injury.
WARNING! Due to the variety in design of vehicles, it is the users full responsibility to ensure no damage occurs whilst fitting. Correct
attachment of the roof box to a vehicle is critical and is beyond the control of the manufacturer, distributor, or supplier.
WARNING! The user must secure the roof box, checking the security frequently when in use.
WARNING! Avoid any protrusions beyond the side of the car as these may present a risk of injury to passers-by.
dO NOT use the roof box for any purpose other than for which it is designed.
WARNING! Drive carefully, - Be aware of cross winds, sudden braking or hard cornering, reduce speed accordingly when using roof
box. Recommended maximum speed is 130km/h.
WARNING! This roof box is designed for temporary use only, remove when not in use and before going through a car wash.
Before every use check the roof box for security of fittings or any sign of wear and tear. Replace any worn or damaged parts.
Check the load is stable and uniformly distributed before transit. Use the supplied luggage straps.
Be cautious of the load height and restrictions due to car park height barriers you may encounter.
WARNING! Be wary of parts of the roofbox protruding from the boundaries of the vehicle, especially the tailgate sweep.
WARNING! Be wary of gusts of wind when installing, two people recommended.
dO NOT exceed the weight limit stated in the roof box specifications.
WARNING! Remember the driver of the vehicle is responsible for the security and safety of the load carried.
WARNING! Warnings and cautions in this manual cannot cover all possible situations. It must be understood that common
sense and cautions are factors which cannot be built into this product, but must be applied by the user.
2. INTROdUCTION & SpECIFICATIONS
The RB320E, RB420E & RB480E Roof boxes are manufactured from HIPS (High Impact Polystyrene) for strength, looks and durability. All
three models are finished in stylish gloss black and benefit from twin point central locking on RB320E & RB420E and triple point central
locking on RB480E. All are supplied with 70mm wide U-Bolts for fitting to most common size roof bars.
Model No:........................................ RB320E............................................ RB420E............................................RB480E
Capacity:.......................................... 320ltr.................................................420ltr................................................ 480ltr
Max Load (uniformly distributed)......50kg..................................................50kg.................................................50kg
Dimensions (L x W x H)................... 1320 x 780 x 360mm........................1450 x 940 x 400mm....................... 1980 x 780 x 400mm
3. pARTS ANd ASSEMBLY
Unpack products and check contents against the list below. Should there be any damaged or missing parts contact your
supplier immediately. Some actions described in 3.2-3.4 may not be required if already assembled.
Item
Description
1
Roofbox base
2
Roofbox cover
3
Keys
4
Hinge pivot pin
5
Clamp plate (2 hole)
6
"U" bolt
7
Clamp knobs
8
Luggage straps
9
Self adhesive patches
3.1.
Unlock the cover safety lock (fig.1).
3.2.
Align the hinge positions and place the cover (item 2) over the base (item 1) of the roofbox. Using the supplied key (item 3), lock the
cover to the base, turning the key anticlockwise (fig.2). Make a note of the key serial number.
3.3.
Insert the hinge pivot pins (item 4) full depth (fig.3). Thumb pressure should be adequate.
3.4.
Unlock the cover and open fully enabling fitting of the spring loaded latches (fig.4). Thumb pressure should be adequate to connect the
ball and socket pivot joint.
3.5.
To close the cover, apply equal pressure with hands near to opposite ends.
fig.2
© Jack Sealey Limited
INSTRUCTIONS FOR:
ROOF BOX GLOSS BLACK 320/420/480ltr 50KG
MAX LOAd
MODEL No's: RB320E / RB420E / RB480E
Qty
1
1
2
2 (x3-RB480E)
4
4
8
2
8
Thumb
Item 4
pressure
fig.3
Original Language Version
2
4
4
1
3
5,6,7,8
Item 2
Item 1
fig.1
Safety lock released
fig.4
On the cover
item 2.
RB320E,RB420E,RB480E ISSUE 1 09/01/14
Related Manuals for Sealey RB320E
Summary of Contents for Sealey RB320E
- Page 1 The RB320E, RB420E & RB480E Roof boxes are manufactured from HIPS (High Impact Polystyrene) for strength, looks and durability. All three models are finished in stylish gloss black and benefit from twin point central locking on RB320E & RB420E and triple point central locking on RB480E.
- Page 2 To obtain a parts listing and/or diagram, please log on to www.sealey.co.uk, email [email protected] or phone 01284 757500. NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.